SDG

  Рет қаралды 21,235

SDG Electronics

SDG Electronics

Күн бұрын

Пікірлер: 92
@sdgelectronics
@sdgelectronics 7 ай бұрын
PCBWay 3D Printing and Fabrication: www.pcbway.com/rapid-prototyping/ FNIRSI HS-02A on Banggood: uk.banggood.com/custlink/vvGSGpQDjC FNIRSI HS-02A on Aliexpress: s.click.aliexpress.com/e/_DdIUrrD FNIRSI FNB48P on Banggood: uk.banggood.com/custlink/KmK9DCbvaV FNIRSI FNB48P on Aliexpress: s.click.aliexpress.com/e/_DDT96Yr Support the Channel with Patreon: www.patreon.com/sdgelectronics
@syn80
@syn80 Ай бұрын
For those who don't like the rolling temp number animation on the HS-02 if you update the firmware to 1.7 you can disable it. Look for "Rolling" in the system section. By default it is ON, just set it to OFF.
@OutOfNameIdeas2
@OutOfNameIdeas2 Ай бұрын
How do you update it
@syn80
@syn80 21 күн бұрын
@@OutOfNameIdeas2 hold down the OK button, plug cable into your PC, then plug other end into your soldering iron. you should see a message pop up on your soldering iron display. you need to drag that bin file to the BOOTLOADER that shows up on your PC. once installed, the soldering iron will reboot. you can now unplug it from your PC.
@jackhowardbourne
@jackhowardbourne 7 ай бұрын
This iron looks genuinely good portable option to use with my current JBC tips.
@mortenhattesen
@mortenhattesen 7 ай бұрын
Looks like a really nice iron. Using JBC T245 compatible cartridges is great. But that horrible scrolling digit temperature display is close to being a deal-breaker. Some Chinese software engineer must have had too much time on his hands and thought it was a good idea to animate the temperature display making it impossible to read until it has reached the setpoint.
@Boz1211111
@Boz1211111 5 ай бұрын
i was confused what scrolling you could possibly refer but after i watched i almost laughed when i seen scrolling!
@Alex_E
@Alex_E 4 ай бұрын
This animation only looks bad on video, but if you watch it with your own eyes, it's nice.
@gregsullivan7408
@gregsullivan7408 5 ай бұрын
I'm confused by the 150W power reading during the coin test - is that for the Aixun? I would have expected the Aixun to be the inset window, but the "150W" is overlaid on the main window.
@seangannon193
@seangannon193 2 ай бұрын
Just got the HS-02A really quite a impressive bit of kit i think Fnirsi are coming on leaps and bounds
@orion310591RS
@orion310591RS 7 ай бұрын
One thing that breaks on Fnirsi, is USB C jack, after some months of usage, usb C jack will start to bend left and right... to prevent total damage i literally epoxy glued that 15cm cable to the soldering iron, now its fixated and cannot move... one plastic part 5-6mm wide in that area would prevent USB C connector being destroyed over time... so plastic part is supporting usb c cable, from all 4 sides... 3:37 - Here you can see that metal connector is not supported by black plastic.
@davadoff
@davadoff 7 ай бұрын
I see it, thanks!
@gregsullivan7408
@gregsullivan7408 5 ай бұрын
Thanks for the heads up. Is there a less permanent method that might work? Is there a glue that could be removed easily with heat, for example? If not a glue, some kind of wax?
@orion310591RS
@orion310591RS 5 ай бұрын
@@gregsullivan7408 You can use hot melt glue. For glue gun. Transparent tube that you put in heating gun and it melts glue. Second solution is to use a lot of isolation tape to prevent moving and bending of connector in jack.
@gregsullivan7408
@gregsullivan7408 5 ай бұрын
@@orion310591RS thanks. So is that clear hot melt glue easy to re-melt? Would there be any risk of damaging the body of the iron or connector?
@orion310591RS
@orion310591RS 5 ай бұрын
@@gregsullivan7408 No risk of damaging as it cools down in 2 seconds. Can be removed by fingers only when its cold. Try on some other material before you glue cable to soldering iron.
@ameliabuns4058
@ameliabuns4058 6 ай бұрын
These have a lot of voltage leak at the tip, but if you use a power bank it’ll be fixed
@antonmilosevic
@antonmilosevic 6 ай бұрын
Hi Steven, you really had me sold on the soldering iron (or is it a staton at this point?). Ordered one this morning off of Ali! One thing that I would have loved in this review would be a teardown of the products and perhaps a guide on how and how much to “overclock” it. It comes with a barrel jack to USB cable, so I assume 20V isn’t a hard limit :)
@electrodacus
@electrodacus 7 ай бұрын
I also got just a few days ago the FNB58 the one without Bluetooth but connectors only pass trough the USB 2 signal not the USB 3 so I need to make a modified cable in order to be able to measure the power consumption of some USB 3 devices. I was interested in testing some USB 3 flash memory and for example on USB 2 it will use 0.19W idle 0.38W max while reed or write on but when connected to USB 3 it will use significantly more around 0.6W idle and 1.8W under load (reed/write). Most new USB 3 flash memories get way to hot so I was trying to find one of the better ones for a project. The ADC resolution is also only 16bit for the current measurement on this and on my older USB power meter it was 18bit. But they show a lot of decimals to look like they are using a higher resolution ADC than they actually do. The interesting thing is that they use antialiasing for the text on the FNB58 so text looks much better on the small screen than on the FNB48. Other than that and menu being a bit different I do not think there is much of a difference.
@sdgelectronics
@sdgelectronics 7 ай бұрын
Ah thanks for the information, I didn't realise the limitation on USB 3.0. Any devices you're aware of that pass through properly?
@electrodacus
@electrodacus 7 ай бұрын
@@sdgelectronics The AVHzY C3 and likely other models they have have USB 3.2 pass-trough at 10GB/s but they are more expensive. I just assumed the Fnirsi had also pass-trough but I was wrong.
@ploxiln
@ploxiln 6 ай бұрын
@@sdgelectronics I have a couple of more basic usb meters which do pass through usb 3.0 (though maybe only 5 gbps): Ruideng UM34 / UM34C (only USB-A connectors pass usb-3) and Ruideng TC66 / TC66C (USB-C only)
@electrodacus
@electrodacus 6 ай бұрын
@@sdgelectronics I need to apologize for the incorrect info. I just opened the FNB58 today and it looks like maybe the two USB-C connectors have the USB 3 connections on the PCB. I do not think I have a proper USB C cable to test that it actually works but it should and also not sure if the FNB48P is the same PCB or different. The USB A connectors are clearly just USB 2
@SeanChYT
@SeanChYT 7 ай бұрын
Good review. I agree the way the numbers in the display changed was not good. It would take me a LOT to get used to that.
@tbangblack4515
@tbangblack4515 7 ай бұрын
We'd love to see the performance of the tips it came with vs jbc's
@davadoff
@davadoff 7 ай бұрын
You’re better off using lesser tips that are genuine (like Hakko T12) than Chinese JBC.
@gregsullivan7408
@gregsullivan7408 5 ай бұрын
Just received the HS-02A (but unfortunately it's a gift for a friend, so I can't try it yet! 🤣) I'm surprised at how small it & the tips are! (I haven't opened it yet, but I got the one with the extra tips, and they are clearly visible, in a separate clear bag) I was concerned that I may have accidentally bought the -B version, but all indications are that it is indeed the -A. Btw I got it from Bangood - the shipping to Sydney was very rapid. Why didn't I get one for myself too? Out of respect for mum, who bought me a conventional soldering station. 😉🤣
@davadoff
@davadoff 6 ай бұрын
EDIT: whoops, the S60 was already reviewed in SDG video #297 Pinecil V2 with short gross tips Sequre S20 with genuine JBC C115 Sequre S60 with genuine JBC C210 …if you’re looking for some review suggestions. To find the best portable iron. Or is the best TS80P?
@seephor
@seephor 7 ай бұрын
picked one up. You can't go wrong for $31 USD shipped. I meant, the case alone is almost worth that price.
@darrens3420
@darrens3420 21 күн бұрын
Is this suitable for a beginner, just need one to solder led strips?
@borayurt66
@borayurt66 6 ай бұрын
How does it perform with that barrel jack adapter connected to a regular PSU? Can it be used with a 24V adapter? Any chance of using it on the field with a 13.8V car battery?
@davadoff
@davadoff 6 ай бұрын
Performance is no different. That adapter just connects barrel jack to the USB power pins. 24v is likely too high for genuine JBC tips (230W if 2.5R load). 15-16v at the cartridge gives 100W with JBC C245. FNIRSI spec says 100W max. 13:23 - It looks like this iron limits the power so maybe 24v will work.
@emils7347
@emils7347 Ай бұрын
Can you advice about your power supply unit? I have 100W GaN USB-C (WEKOME WP-U155) with 100W USB-C cable, but I can set maximum 65% of power and I wonder if it's the charger fault or I do something wrong.
@DamianYesiolowow
@DamianYesiolowow 2 ай бұрын
My solder not working. Used about 5 times and not heating up but it shows 650 degree celsius on screen, not work on every 6 tips. Why its not heating up? Any solution?
@JimMcPartland
@JimMcPartland 4 ай бұрын
Can you share a link to the one you say it's not a powerful as at approximately 16:40 in the video?? I can't make out the name. Thank you in advance.
@spy590
@spy590 4 ай бұрын
I believe it is Aixun
@jinlsui
@jinlsui 5 ай бұрын
As the device is rated 100W, have you ever reached peak power near 100W output on your reading, if your power supply is cable of 100W or more? Recently I bought a similar product rated 100W, but my reading was never more than 4.2A on 20V (from both of my PD 100W power supplies), even though I could set the max current on my solder as 5A.
@joepastafari
@joepastafari 2 ай бұрын
pretty weird that I stumbled on this video right after buying these almost exact items, except I got the FNB58
@vanxgamer9843
@vanxgamer9843 Ай бұрын
Comparing this to the UNBRANDED T210 from SDG #344 and the KSGER C210 Portable, which one is the best? Hoping for your reply!
@sdgelectronics
@sdgelectronics Ай бұрын
@@vanxgamer9843 this one I think
@evensteve284
@evensteve284 5 ай бұрын
Questions from a novice: 1.) How do you know what power supply to buy? I've been to FNIRSI's web site and no info is provided. And no mention of it here in this video either. 2.) I think I'll need the JBC 245442 chisel tip as I plan to use this for through-hole PCB work. Can I order this unit with just that tip?
@Quixilir
@Quixilir 5 ай бұрын
On fnrisi website theres a option that includes the charging cable with the charging plug for aditional 30€
@MrRawUK
@MrRawUK 4 ай бұрын
If you already have a Pinecil then this is not really a major upgrade right?
@MoreCharactersThanNeeded
@MoreCharactersThanNeeded 7 ай бұрын
There is also a HS01 version that takes T12 tips. Would be nice with a comparison.
@mortenhattesen
@mortenhattesen 7 ай бұрын
I believe the HS01 tips are a shortened version of T12, so using standard T12 tips is not really an option
@fredericktodd5789
@fredericktodd5789 5 ай бұрын
Good video. Can you purchase the power brick buy itself?
@bosstaki
@bosstaki 6 ай бұрын
Hi there! Absolutely love watching your videos mate! Which make & model of soldering station would you please recommend for an absolute beginner! Starter kits! Keep up the good work mate! I’ve been looking at the T320 station?
@sdgelectronics
@sdgelectronics 6 ай бұрын
Thanks! The T320 is good, I haven't had any issues with mine. You could consider the Jabe/Best JBC style station too
@bosstaki
@bosstaki 6 ай бұрын
Thanks for the reply mate! Where do I find the jabe/best stations please!
@supperka2
@supperka2 6 ай бұрын
Hello, what tin do you use in video?
@abzaman77
@abzaman77 7 ай бұрын
I was gonna ask about it in some recent video of yours. Glad you reviewed it! Also, there's a new mini spot welder from them something like SW 10. Would please review that too? Tia.
@maswilly8162
@maswilly8162 6 ай бұрын
hi, does the FNIRSI hs02A soldering bit support AIXUN soldering bit?
@neverendingstudent
@neverendingstudent 3 ай бұрын
I think it would so long as you use the T245 compatible cartridges, since they are both designed to be compatible with JBC style 245s.
@gregsullivan7408
@gregsullivan7408 5 ай бұрын
You say it works fine with genuine C245 cartridges. Does that mean you've actually tried it? Genuine cartridges, having a resistance of about 2.5ohms, would need to draw greater than 5A to reach 100W - can this iron run at > 5A? (perhaps using a suitable power supply & the supplied barrel to USB-C adaptor)
@gregsullivan7408
@gregsullivan7408 5 ай бұрын
I just asked Fnirsi what the resistance of their tips are, and it is in fact 2.5 ohms! So the iron actually has a DC-DC converter??? I thought it would be very simple, and simply switch the input power on & off. How on earth can it dissipate the conversion losses? I must be missing something.
@sdgelectronics
@sdgelectronics 5 ай бұрын
@@gregsullivan7408 everything 15:00 onwards is using genuine JBC cartridges
@gregsullivan7408
@gregsullivan7408 5 ай бұрын
@@sdgelectronics excellent - thanks. I'd be interested in an explanation of how it can do the voltage conversion so efficiently - have you discussed this already perhaps, in another video? Btw it's an absolute pleasure watching your presentations - you're an excellent speaker. Thankyou.
@suncrafterspielt9479
@suncrafterspielt9479 4 ай бұрын
I want to use this as my primary soldering iron, does anyone know a good stand for this iron?
@awo256
@awo256 7 ай бұрын
Interesting product and a good review. Will it work with 65 W power bank?
@sdgelectronics
@sdgelectronics 7 ай бұрын
Yes, you will need to set maximum power to 65% though.
@fluoxethine
@fluoxethine 7 ай бұрын
Why do they still use Times New Roman for these devices? It's such a bad font for such displays.
@davadoff
@davadoff 6 ай бұрын
To support Chinese characters. Latin letters are more of an afterthought.
@Ismsanmar
@Ismsanmar 7 ай бұрын
Are you sure that the screen on the soldering iron is an IPS LCD? It seems to me to be one of those recent color mini OLED displays by the way that it shows the black color, without any backlight bleeding.
@sdgelectronics
@sdgelectronics 7 ай бұрын
Yes definitely LCD. You can see the backlight bleed on it in a dark room.
@AKG58Z
@AKG58Z 3 ай бұрын
Can it hold c115 tips
@DarkStormPhoenix
@DarkStormPhoenix 7 ай бұрын
Thank you for great review love the channel. Please whats the difference between the A version you havr and the hs02B version please .??
@sdgelectronics
@sdgelectronics 7 ай бұрын
Just the colour. The HS-02B is all black
@DarkStormPhoenix
@DarkStormPhoenix 7 ай бұрын
​@@sdgelectronics thank you so much I thought I ordered the wrong one lol Should be here tomorrow fingers crossed And again thank you so much for the reviews. They really do help myself and others out so much.
@eggmangoogle3146
@eggmangoogle3146 7 ай бұрын
@sdgelectronics It was my impression that the B model uses T210 tips. The FNIRSI store also says that the A model uses tips with a heating core resistance of 2.5 ohms, while the B model tips' heating core resistance is 2.1 ohms. Apart from that, both irons and tips are different lengths, 13 vs 13.5 cm and 9 vs 6.6 cm, respectively, for the A and B.
@DarkStormPhoenix
@DarkStormPhoenix 7 ай бұрын
​​@@eggmangoogle3146hello yeah my iron just turned up. Cam definitely confirm tips are very short and also end of iron silver mounting part looks different.. Now I don't know if the a or b version is better 😂😂
@zuxel6
@zuxel6 6 ай бұрын
Hs02a for 245, hs02b for 210 tip
@gregsullivan7408
@gregsullivan7408 5 ай бұрын
Can anyone recommend a suitable cable, heat resistant, about 1.5m long?
@TYGAMatt
@TYGAMatt 7 ай бұрын
Great review on the HS-02. Thanks Steve. So, do I retire my HS-01? Decisions decisions....
@-COBRA
@-COBRA 7 ай бұрын
the handle looks chunkier than hs01
@OnlineObsessionista
@OnlineObsessionista 4 ай бұрын
make sure you upgraded to 1.6 version
@jaro6985
@jaro6985 6 ай бұрын
Fnrsi USB tester hardware is great. UI is terrible, hate the scroll wheel. Good review
@jeffreydoujon638
@jeffreydoujon638 7 ай бұрын
No Kelvin or Rankine ! The Horror, The Horror 😝
@iLLumenaughty_9
@iLLumenaughty_9 7 ай бұрын
we need a mic change from u sir, current mic's audio is a little harsh n sharp for some reason
@CM-xr9oq
@CM-xr9oq 7 ай бұрын
Nope, sounds fine to me.
@sdgelectronics
@sdgelectronics 7 ай бұрын
Might just be my voice. Had a chest infection a few weeks back, but still not 100%. I'll tone down the HF in the EQ settings
@DarkStormPhoenix
@DarkStormPhoenix 7 ай бұрын
Sounds perfect to me also
@teslatrooper
@teslatrooper 7 ай бұрын
sounds fine to me
@davadoff
@davadoff 6 ай бұрын
@@sdgelectronicsit sounds good. Your voice sounds very deep, but I guess that’s what your voice really sounds like. I have decent audio setup with a $1000 DAC. The only thing you need to change is adjust the music by at least -6dB. I’d prefer no music though. Maybe you could do ASMR soldering videos for the subs lol.
@anenglishmaninbrazil3212
@anenglishmaninbrazil3212 7 ай бұрын
I was going to buy this after watching the video but the iron is 263Rs in Brazil which is about £45 but the Tax to get it here is 254Rs the joys of living in Brazil ffs
@DciMaluko
@DciMaluko 7 ай бұрын
If you work fixing MacBooks, don't buy it. This ampmeter messes up the 5 to 20v negotiations.
@MrFrambooise
@MrFrambooise 5 ай бұрын
what do you mean, it's delivering wrong voltage? or it's just not working?
@DciMaluko
@DciMaluko 5 ай бұрын
@@MrFrambooise If you use it, 5v is not gonna go up to 20v. The whole point of using ampmeters with macbooks is to analise the voltage negociation and amperage. This thing is useless for me if it doesnt let me see that. It stays at 5v.
@bjt3833
@bjt3833 3 ай бұрын
@@DciMalukoyou likely need to flip one of the usb C connections. Most usb testers only work in 1 orientation. So if it’s not negotiating properly, just flip a single usb C connection. It’s also possible you need to update the firmware on yours.
@DciMaluko
@DciMaluko 3 ай бұрын
@@bjt3833 The 2 bucks one I have works both ways. There is no excuse for it.
@BAD_CATpv
@BAD_CATpv 7 ай бұрын
Fnirsi тупая компания, мой паяльник сгорел и-за брака ихнего переходника и мне отказали возмещать его стоимость.
FNIRSI HS 02A vs B (Which one should you get)
16:49
Chain Breaker
Рет қаралды 3,1 М.
Что-что Мурсдей говорит? 💭 #симбочка #симба #мурсдей
00:19
How Strong Is Tape?
00:24
Stokes Twins
Рет қаралды 96 МЛН
SDG #352 Quick TS11 Intelligent Soldering Station
22:33
SDG Electronics
Рет қаралды 6 М.
FNIRSI HS 02A HS 02B Firmware (update)
10:08
Chain Breaker
Рет қаралды 1,9 М.
SDG #345 KSGER PD210 USB-C JBC Style C210 Soldering Iron PD3.0
18:46
SDG Electronics
Рет қаралды 10 М.
#2059 FNIRSI HS-02A Soldering Iron Review
14:59
IMSAI Guy
Рет қаралды 3,6 М.
SDG #344 TS-210 USB-C JBC Style C210 Soldering Iron PD3.0 QC3.0
13:38
SDG Electronics
Рет қаралды 10 М.
FNIRSI HS-02A 100W USB Type-C Soldering Iron
10:36
ErCan Everything
Рет қаралды 15 М.
FNIRSI HS02 Smart Soldering Iron First Look
17:31
12voltvids
Рет қаралды 11 М.