Somethings to add make sure to only run the ski 30-90 seconds because the carbon wear ring doesn’t get water when hose is hooked up and it will over heat. Also if you pull the oil pump tube out a little you can hold the throttle and hold the start button the ski will crank only and this will allow excess trapped oil in the passages to be flowed down to the bottom of the pan then tube pump again!
@dominickdelduco24713 жыл бұрын
Forgot to manually crank the engine ( depress throttle and start button) doing this allows engine oil to flow into oil filter compartment. Do this until ALL all oil is out.
@Herooftheday643 жыл бұрын
Good way to wreck your carbon seal. The manual says to never run it over 90 seconds even if it's on the hose, because the seal gets no cooling.
@larky368 Жыл бұрын
5 minutes! That thing must have been red hot. All you have to do is spray through the intake grate to get some water to the carbon seal.
@pdxwildchildroberts5586 Жыл бұрын
Yikes..Carbon seal..spendy fix..no need to run, eva..just turn it over, holding throttle down for count to 5-10 at start, and 2-3X during oil removal..should get 2-2.5 qts..and replace the star-nut O-ring on the Cap, also👍
@craigaustin47794 жыл бұрын
I got one of those last week, a similar pump failed after about 10 changes. Hopefully this one is more durable, but compared to dealer oil change prices ,you could buy a new pump for every oil change.
@larky368 Жыл бұрын
Next time you have the deck off and you need to run the engine for a long time try pointing a hose through the intake grate towards the front to get water down the shaft to the carbon seal. You can reach down and feel the steel flange that spins on the carbon seal and see how much cooler it is.
@randymueller23492 жыл бұрын
I'm a Retired Professional Wrench, I use a Pneumatic Air Operated Fluid Evacuator that contains up to about 8 Liters of Fluid, easily transported with 1 hand and simply pour out the the Fluid into an appropriate Reclamation Tank. Note: Compressed Air required (Shop Compressor). Randy AKA randog311
@MAX_max_20243 жыл бұрын
Bob, very informative! Would be great to see the winterization & de-winterization procedures, or possibly have it explained to mechanic (similarly how you've done with stones damage on your sea doo).
@bobsudeyko40883 жыл бұрын
One thing. When warming up your Seadoo only run it for 1 to 1.5 minutes.
@richardnagrabski9301 Жыл бұрын
Informative? Wrong information all around. Using used oil to lubricate the new ORings was the icing on the cake for epic fail. This guy is a hack..
@rickmoohs961911 ай бұрын
@@richardnagrabski9301Are you serious? Do you really think using a miniscule amount of used oil on a oring is going to affect anything 😂😂
@strobaholic2 жыл бұрын
I hope you took Nathan for a ride on the Seadoo. He worked hard for it. 😄
@bobsudeyko40882 жыл бұрын
J His mum won't let him go
@strobaholic2 жыл бұрын
@@bobsudeyko4088 Well I guess you’ll just have to take her along with you. I’m sure she’s really cute lol.
@shmontrostov3 жыл бұрын
Per Users Manual, you should not be running it more then 2 minutes - Drive line seal has no cooling when watercraft is out of water. Please correct me if I am wrong?
@Ipera783 жыл бұрын
That was the first thing that came to mine mind, 5min sounds like a lot,
@DougsMessyGarage4 жыл бұрын
I’m going to have to that job twice in the not too distant future
@jacksonvillejetriders6529 Жыл бұрын
Do oil changes after a ride. Already to a good temp for removal without stressing the carbon seal
@jimmymusignac18313 жыл бұрын
You warmed the Ski for 5-7 minutes, that is a no no in a SeaDoo. Then you used dirty oil to lubricate the O-rings, wow. Your next video should be how to replace the carbon ring.
@NorthwestSawyer3 жыл бұрын
Everyone needs a Nathan! Great video. Do you happen to have a link for the pump you used or the name maybe? Thank you!
@bobsudeyko40883 жыл бұрын
It’s stored away in the seadoo for the winter. I just searched on Amazon and found it there.
@NorthwestSawyer3 жыл бұрын
Thanks for responding. I think I found it.
@nike12000haha3 жыл бұрын
Maybe i missed it but should put it in drown mode and crank then Re suck the crank case
@HugoAlmeidaJr4 жыл бұрын
Bob, really nice job. Own two of theses same 300 Limited skis and maybe now will attempt to do the next oil change myself!
@bobsudeyko40884 жыл бұрын
Fairly simple. Particularly after you have done it once. Just make sure at the end of it all that the dip stick measurement is right. Let it run for 3 to4 minutes to get an accurate reading. If to much suck a little out. At the dealership the cost is high but even more of an issue is that you might have to weight weeks without your machines.
@bobsudeyko40884 жыл бұрын
Wait
@szeldov3 жыл бұрын
@@bobsudeyko4088 From my 2019 GTX manual: NOTICE Never run engine longer than 2 minutes. Drive line seal has no cooling when watercraft is out of water.
@aaron-fauth3 жыл бұрын
You should be doing it yourself
@curtisrice51003 жыл бұрын
Well bob . Just wondering . Did it end up ever sinking ? Notice a lot of people were saying your carbon seal may be toast for running that long out of water !??
@bobsudeyko40883 жыл бұрын
No problem with the carbon seal. I probably only ran it for about three minutes. It is correct however that it really shouldn’t be run for much longer than that. I misspoke when I said 5 minutes.
@richardnagrabski9301 Жыл бұрын
You misspoke during the entire video. Stick to what you do best..
@azr2d1 Жыл бұрын
@@richardnagrabski9301 I agree. Let a pro (or backyard mechanic with at least a few oil changes under his belt) do the work. He also didn't change the small O ring. FAIL.
@shanepeay53723 жыл бұрын
poor carbon seal..... never run over 2 min out of the water........ :/
@ivgot12 жыл бұрын
5 to 7mins ,Not!!!..1 fried carbon seal, 60 seconds max..
@AdamGeorgeLL10 ай бұрын
Great Video. Where did you get that funnel from?
@marcinos7083 жыл бұрын
I'm currently a Yamaha PWC owner. what is the supercharger maintenance look like on one of these. We are looking at adding a second unit
@hookdup19273 жыл бұрын
Is there something electronically you have to reset in the computer after doing an oil change?
@bobsudeyko40883 жыл бұрын
If there is I don’t know. I just change approx every 50 hours
@hookdup19273 жыл бұрын
@@bobsudeyko4088 i looked into it. It seems A 400$ diagnostic tool called candoo professional is needed to reset the maintenance icon .
@azr2d1 Жыл бұрын
@@hookdup1927 I seem to recall seeing it mentioned in owners manual how to reset it......
@deninhodovalle3 жыл бұрын
I got a kit and it comes with 2 oil filters and I can't find the place where the second one should be, if it exists. Any advise?
@bobsudeyko40883 жыл бұрын
The machine only uses one oil filter
@lennyortiz1734 Жыл бұрын
hey bob is there a bit of a gap between the top cap of the filter and the housing like can you see the o ring a bit ?
@TheReinoPaasonen Жыл бұрын
There is and its normal.
@bobsudeyko4088 Жыл бұрын
Correct
@eddiea81674 ай бұрын
This was my concern. Thought I was doing something wrong and didn’t want to start it. Doing the oil change right now for the first time.
@mogulpro4 жыл бұрын
Is that double LinQ platform aftermarket or did you make it ? PS- Nice video. We ride all the same places but never bumped into ya.
@bobsudeyko40884 жыл бұрын
It's aftermarket. You can find more about it here. facebook.com/BSDesigns4PWC It's kind of expensive for what it is. Not the companys fault. Mostly exchange and if you are unlucky at the border you may get hit with duty charges. Almost 600 Cdn for me. Built well and works well.
@user-il6cy8mi9n7 ай бұрын
Helpful thnx
@bflinders72754 жыл бұрын
Hey from Oz, I like your extra platform, did I miss the video on it? Which one is it and can you put two linQ items at once with the full seat on?
@bobsudeyko40884 жыл бұрын
facebook.com/BSDesigns4PWC Thats the link to the guys who make it in I think florida. It's expensive. Their price isn't to bad but then theres the exchange rate the shipping cost and if you luck out maybe a duty cost. For me the whole thing was almost 600 Cdn by the time I got it. Yes you can carry the top case the cooler and extra gas with the back seat on. I think it works pretty good and now I can bring everything with me if i want too. Tell the guys Yukon Bob referred you if you go for it.
@bflinders72754 жыл бұрын
Thanks Bob! I will look in to it. Thanks for your videos!@@bobsudeyko4088
@Maliken19922 жыл бұрын
Hello Bob, just curios why did you heat up the oil before changing it?
@bobsudeyko40882 жыл бұрын
It just allows it to be more viscous and then makes it easier to drain more of it. Should not run the engine more than about two minutes.
@Maliken19922 жыл бұрын
@@bobsudeyko4088 thanks, I bough the same pump on amazon it works great.
@azr2d1 Жыл бұрын
@@bobsudeyko4088 Ideally you do this after a day at the lake. Drive it home and change the oil right away. It should be nice and warm still. Doing an oil change end of season (when it's colder) will suck, especially with the synth blend oil. Use full synth.
@bobsudeyko4088 Жыл бұрын
Just so that it change the viscosity a little and allow it to flow a little more easily.
@lawnman15004 жыл бұрын
Where you jetting this weekend Bob?
@jrdaviskid3 жыл бұрын
Does the oil filter container secure flush? I’ve tried several times and there is a small gap every time
@bobsudeyko40883 жыл бұрын
It should just spin on to a little beyond hand tight. There is a rubber seal that also needs to be in place where the filter meets the engine. I have not noticed a gap once it’s tightened a little beyond snug.
@jrdaviskid3 жыл бұрын
@@bobsudeyko4088 thanks Bob. I still see a small gap. Is there a rubber seal other than the o rings?
@bobsudeyko40883 жыл бұрын
@@jrdaviskid no there is just the one rubber ring. It’s not really an o ring as it is flat. The old ring that is already on there needs to be removed. Sometimes the rubber seal that is on there will stick on the engine mount and will not come off with the filter. Only one ring at a time is used.
@deplorablechump8758 Жыл бұрын
Didn’t measure how much you put in? 😁
@sirfitz8125 Жыл бұрын
Five minutes?! Eeeeekkkmmm😂
@andrewgarcia85893 жыл бұрын
aweee your dog is so cute and howcome you never bring him with you on one of your trip
@bobsudeyko40883 жыл бұрын
Not my dog. Just baby sit once in awhile.
@andrewgarcia85893 жыл бұрын
@@bobsudeyko4088 ahh tru but proberly when its get older right and by the way bob you have a merry chrismas and a happy new year as well for your family and hop 2021 ill be a deffrient year
@davidoberhofer5814 жыл бұрын
Bob - how do you reset the "oil change required" message?
@bobsudeyko40884 жыл бұрын
Good question. I don’t know. I have never had it come on. Must be something in the manual. You must have to toggle through the menu and reset something in the settings. Sorry I cannot help anymore.
@szeldov3 жыл бұрын
@@bobsudeyko4088 Maintenance Reset (only if maintenance is required) Using right arrow button, Select RES MAINT and hold OK button to reset maintenance. NOTE: The maintenance reset can only be done within the first 15 seconds of ECM wake-up.
@deplorablechump8758 Жыл бұрын
Run it for 4-5 minutes?
@arnelarsen40734 жыл бұрын
Read your owners manual for oil Quantity/quality
@brucearduser352 жыл бұрын
What is the name of the pump you used??? Where did you buy it??
@bobsudeyko40882 жыл бұрын
There is no name on it. I bought it from Amazon. Just google oil pumps and see what it give’s you
@brucearduser352 жыл бұрын
@@bobsudeyko4088 Thanks much for the video .... great job! I went to amazon and found the pump ... $20
@bobsudeyko40882 жыл бұрын
@@brucearduser35 one thing Bruce. Only run it for about 1.5 minutes to warm up the oil. I misspoke when I said d 5 min
@bansterref3 жыл бұрын
Where you bought the pump?
@jasontippmann2083 жыл бұрын
It should have been more like 4.5 litres of oil and the carbon seal probably toast.
@jsheavy39233 жыл бұрын
Run it that long out water i bet u just burned up ur carbon seal.
@boryakellys3 жыл бұрын
Аймаладец!
@alainbrouillette7740 Жыл бұрын
Hey Bob i know this is an old video , would you have a link to this pump ?
@bobsudeyko4088 Жыл бұрын
No I don’t but I bought it through smazon
@alainbrouillette7740 Жыл бұрын
@@bobsudeyko4088 Thanks i will look into this .
@joeross9523 жыл бұрын
How do you reset the light?
@bobsudeyko40883 жыл бұрын
I don’t. Just change the oil every 50 hours.
@alnyc42133 жыл бұрын
great job .. keep it up
@arnelarsen40734 жыл бұрын
Are you using Synthetic Oil?
@bobsudeyko40884 жыл бұрын
Yes it’s a synthetic blend. Comes in a kit from the dealer along with the filter. About 85.00.
@Whatnissan2 жыл бұрын
Bro you know it’s only 2 min right ? Poor carbon seal
@quinnsmith61192 жыл бұрын
Who agrees this guy is not very smart
@Flybynight_21124 ай бұрын
A whole lot of bad information and omitted information. You should not be giving advice on you tube. Please stop.
@richardnagrabski9301 Жыл бұрын
Using old contaminated oil to lubricant the new o rings? Really!! How about cranking the engine to remove remainder of the old oil. Bad advice all around!