Sure I took a 30 second task and made a 6min video. But this is the easy peasy way to get it done the first 30sec time around ;)
Пікірлер: 28
@johnpillinger72204 жыл бұрын
Just did this on my 81 passport, adjusted this maybe 4 times by feel without ever being satisfied with the result. Did it exactly as you show to, now it shifts amazing, thank you!
@happyseany4 жыл бұрын
So you're currently my hero! Couldn't figure out why my 81 Honda Passport was shifting so crappy. Thanks dude! Lifesaver!
@stephengoodwin Жыл бұрын
Thanks for this Video worked great.
@dustins41944 жыл бұрын
My cart takes some time to get going. I've adjusted the clutch in many ways and the brakes are not hanging. It rolls in neutral very well. The best I can get it still has no power. It starts slowly and picks up steam, but when starting up any sort of hill, it gets louder but doesn't actually move faster (if at all). It's like the gears are just spinning and not hooking up. The longer you ride it, the hotter it gets and the worse it gets. The kicker is that it works much better in reverse. It will actually go, but terrible in forward.
@buyingdrop0127 Жыл бұрын
Mine is the same did you ever fix it?
@dustins4194 Жыл бұрын
@@buyingdrop0127 replacing clutch soon.
@bentallman75973 жыл бұрын
Just put a socket over it with ur flat head through ur socket then just use vise grips to turn ur socket
@dustsmoke3 жыл бұрын
You know you're using a 9/16th on a 14mm nut? Good way to round them off.
@AlanYehle3 жыл бұрын
9/16” IS 14mm.
@dustsmoke3 жыл бұрын
@@AlanYehle haha, no... 14mm is *almost* 9/16. This isn't really a debate and you can verify for yourself elsewhere.
@henrymallett68473 жыл бұрын
i was thinking the same thing lol
@onlysnaps69 Жыл бұрын
@@AlanYehle not how it works buddy
@ptsdgopedsnbikes8156 Жыл бұрын
@@onlysnaps69 😂
@lonnycom76 Жыл бұрын
noice! thx
@troycotsenmoyer67362 жыл бұрын
Can you tell by looking at the adjusting screw for the clutch if your clutch plates are worn?
@MultiMoveman4 жыл бұрын
I have a 1977 honda atc 110, is that semi auto? Cause i don't see a clutch level or anything like that
@kylarmurdock4014 жыл бұрын
Yes semi auto
@MSB11803 жыл бұрын
MY 50 cc Honda gear is so hard and jerks what should i do
@johnnybahama4973 жыл бұрын
Good grief ya'll You loosen the lock nut and turn the screw piece about a full turn to the right " clockwise " then you turn the screw back to the left " counter clockwise " until you feel resistance then back to the right 1/8 turn more or less and lock down the locknut while holding the screw so that it doesn't move. The lock nut is 14 mm only !! Not 9/16 th. The locknut loosing is best done with a wrench but a socket will do to break it lose if a Moron has been the last to snug it up.
@hurstshiftin98734 жыл бұрын
Great vid brother.
@crusadershuakbar4 жыл бұрын
one full turn to the right? is that 360% or 180% ?
@KhNguyen_3 жыл бұрын
360° is right 💁♂️ Example: 1/8 turn out = 45° 👨🔧
@crusadershuakbar3 жыл бұрын
@@KhNguyen_ sometimes one turn is only 180%, just checking, cheers