King Pin Replacement

[@antoniomancini1794]

I was waiting for the very end of the video and I was wondering how you refill The hub oil anyway that was a great video good job.

[@SemiWorkin]

Thanks for watching!!

[@117BMF]

There is a rubber plug in the center of the hub cap. Remove it and fill to the line.

[@charlestalton1825]

I like the tell/no tell nut loose arrows.👍

[@David-yy7lb]

I am surprised there isn't some kind of press to press out the kingpin...but excellent job with no annoying background music 👍🏾👍🏾

[@10YearOldTom]

There is. Use it.every time. OTC brand

[@SemiWorkin]

Thanks for watching!!

[@iankerr1549]

Tiger tool has one

[@Sojourning_]

my favorite hammer. done a lot of those back in the day.

[@SemiWorkin]

Thanks for watching!!

[@DIRT-BOSS]

Do you replace the hub seal ?

[@SemiWorkin]

Thanks for watching!! Yes seal was replaced it just didn't make it in the video.

[@cliff8014]

@@SemiWorkin I was about to say I didn’t see the hub seal and bearing replaced after removal thank you for replying to this!

[@nickmatoic9096]

If you jack the steer axle up every time you service won't be replacing king pins n bushings same for trunions .

[@nickmatoic9096]

A little bit of grease n oil n filters go along way .

[@SemiWorkin]

Thanks for watching!!

[@dirtfarmer7472]

When I was driving the kingpins & bushings took grease or were jacked up so they did take grease

[@jaygraham5407]

I can't imagine a king pin being worn that bad!!! WOW!!!

[@metaagyel620]

Another great video thanks for making it!!

[@SemiWorkin]

Thanks for watching!!

[@franciscovaldovinos1951]

You working that chair 🪑 😂😂😂

[@thebaycuddy]

Indeed a fascinating video, no need for talking

[@rmhanseniii]

What are those red things underneath the wheel lug nuts?

[@mr.george-pht]

Wtf? Dude was driving around like that? 😂 that’s insane. He must have had a serious vibration and death wooble 😆

[@SemiWorkin]

Thanks for watching!! You wouldn't believe some of the stuff I see.

[@cbmech2563]

It's not difficult to get apart until you have get out the hot wrench . And if you don't have to replace the spindle it's not badly worn either . I'm a trash truck mechanic and some of the garbage I see is worse than what goes in the truck

[@alexistroncoso5503]

Buen video saludos desde chile

[@johnb1121]

I love your videos 😍😍😍😍

[@SemiWorkin]

Thanks for watching!!

[@johnb1121]

@@SemiWorkin need more videos please an brakes and air system then electrical please ever bit helps

[@dennissmith460]

Were you able to just replace the bushings, and kingpin with a standard replacement, or did the spindle require extra machining and a oversized pin ?

[@SemiWorkin]

Thanks for watching, I used a standard size king pin and bushing. The pin wore through the bushing causing damage to the spindle. Had to send it off to a machine shop to be sleeved. Here's the video showing the bushing replacement:kzbin.info/www/bejne/r32tcpicbbOjgcU

[@reecewharf]

Did you replace the bushings?

[@SemiWorkin]

Thanks for watching!! Yes I did check out the video here: kzbin.info/www/bejne/r32tcpicbbOjgcU

[@CTSCAPER]

You make it look so easy! I think you need a bigger impact?

[@SemiWorkin]

Thanks for watching!!

[@mike4796]

Well done

[@SemiWorkin]

Thanks for watching!!

[@richardsmith7783]

That is a f-en job changing them !!

[@SemiWorkin]

Thanks for watching!!

[@jeremyrock9305]

Yeah it is done this several times! Even worse job is fifth wheel boom pivot bushings 👍🏻

[@rmdhndwi]

Are all american made trucks use oil in their hub? Instead of grease

[@soillife1]

More and more all along. But many still run packed grease bearings.

[@rmdhndwi]

@@soillife1 what's the benefit then?

[@soillife1]

Ramadan In my opinion. Its personal choise.

[@SemiWorkin]

Thanks for watching!! 90% of the trucks I work on are oil hubs.

[@JuancarlosLopez-s8j]

Manda un video pero como se quita con freno de pastiyas

[@timerickson7056]

I'm 60 been working on junk my entire life . I have never ever seen such worn out king pins.

[@SemiWorkin]

Thanks for watching!! You wouldn't believe some of the junk I see and nobody takes care of stuff anymore.

[@FJCTrucking]

Ever had an issue after is all done you go to grease it and the cap comes out?

[@SemiWorkin]

Thanks for watching!! Yes I run into that a lot.

[@brendanrapa8579]

Why do you put the nut back on the spindle when your working? So you don't loose it?

[@DieselFuelOnly]

protects threads too

[@SemiWorkin]

Thanks for watching!! Main reason is to protect threads.

[@lijoraju6960]

why not apply grease for bearing??

[@SemiWorkin]

Thanks for watching!! Bearing uses oil instead of grease.

[@carlosrobertonascimento3725]

Se ninguém prestou atenção, faltou o retentor interno da ponta de eixo, a não ser q ele tenha dado pause e colocado sem a gente ver. Mas o serviço foi bom.

[@joshuabaker5712]

You k kw if you hit the knuckle instead of driving the TRE down by the ball joint it comes out a lot easier and you dont ruin a TRE.

[@SemiWorkin]

Thanks for watching!! I usually don't reuse TRE and this way is pretty easy.

[@robertb6462]

Nice work. Not fun by no means. Don't miss it myself. But I have to ask, why after all that work did you not replace the anchor pin with the new brakes?

[@SemiWorkin]

Thanks for watching!! There was nothing wrong with the anchor pin and this style it doesn't come with the hardware kit.

[@robertb6462]

@@SemiWorkin Thanks for the reply. Just wanted to ask bc of my curiosity. I guess if they suggested it be changed, it would be in the hardware kit. Thanks for the videos.

[@nonsequitur807]

How much does that job cost parts/labor?

[@SemiWorkin]

Thanks for watching!!

[@dirtfarmer7472]

A lot, money well spent, a little late for my taste.

[@gustavohidalgojr.6343]

Forgot back bearing

[@SemiWorkin]

Thanks for watching!!

[@УрсулецУрсулец]

Как тяги сбивает руки оторвать далдону

[@robzilla1752]

Ever try an electric hammer to beat out that king pin?

[@SemiWorkin]

Thanks for watching!! I've tried just about everything even a 50 ton press struggles sometimes and sometimes they fall out.

[@kenbass3862]

I've done my share of those 😡🤬. Nice job guys 👍.

[@SemiWorkin]

Thanks for watching!!

[@ДмитрийКораблёвК]

Привет из России Тольятти.

[@ЮрийНиколаевич77]

Привет из Подмосковья. ✊

[@rafaelgarcia8538]

Te falto poner el reten camarada

[@사이퍼-w9d]

Как можно ездить с такой шкворней

[@odairalvez6186]

Se o terminal d direção tava bom agora pode trocar acabou com a rosca com aquelas marretada kkkkkk

[@НиколайТищенко-л2п]

На поперечной тяге,левом наконечнике забил резьбу.

[@ГришаВасильев-ы8щ]

А что они в ступицу льют

[@TheTotal5]

Хорошо делает, а не как у нас, на коленке, рожковыми ключами и конченым молотком с железной рукояткой

[@ДенисСеверинов-э6м]

Охуеть он тяги сбивает....