Wow, I finally found the right video! I was using my 4WD on my 2007 Chevy Z71 and was getting stuck so I was trying to shift into 4 Lo and these lights came on, I turned off the truck and turned it back on and was able to get unstuck. But also I’ve heard a bad abs speed sensor can cause an issue with brake pedal going to the floor at low speeds because the ABS turns on because of a bad sensor ! Thanks for the video!
@tommygun5.32 жыл бұрын
Best of luck. Let me know how it goes.
@MrBeastmode902102 жыл бұрын
Thank you for making this video I think you honestly just saved me a couple hundred dollars by taking it to the shop and I can do this myself
@mike_svoeuy11623 күн бұрын
Had this same issue. Had to replace my front wheel hub and it fixed it.
@devinfairchild1833Ай бұрын
Hey man just wanted to say thank you very much for this video You saved me a lot of time and money by knowing what to check and how to check it
@Rcknroler9132 жыл бұрын
Would have been nice to see what you were testing.
@Daddy_D20152 жыл бұрын
The ends he's touching the connector to the sensor
@seandonnelly31502 жыл бұрын
Pretty obvious
@AZHerps Жыл бұрын
AGREED, was just going to make a comment then saw this one, great video but can't see a thing the leads from meter are going to.
@americanpatriot2999 Жыл бұрын
He unplugged the abs wheel sensor from the harness where its mounted to the frame. He then inserted the multimeter test leads into the connector. With the meter set on ohms, he measured the resistance of the wheel sensor. No resistance indicates a shorted or bad sensor.
@jl456 Жыл бұрын
@americanpatriot2999 no resistance showed a bad sensor!
@TourettesMobileMechanic2 жыл бұрын
Ummm. You know it’s a ground wire issue and the grounds are right above it is two. They are rusted out. I just fixed this. It’s not the OHM test lol. You treated the same so I’m not sure what you showing but it was interesting?? Either way. You have the ground location in the video. It runs up near the wheel fender. Goodluck, I’m sure it popped right back in, clean up that metal or run a ground to the block. Good stuff. I did it all day the other day.
@santiagodavila14263 жыл бұрын
Great video… I have a 2007 Yukon 5.3 and this is on and off in my dash… Service traction control Service stabilitrack Service park assistant Service tire monitor system
@tommygun5.33 жыл бұрын
Thank you. Most likely the Service traction control and Stabilitrack are linked to the same problem. Best of luck and let us know what you find.
@santiagodavila14263 жыл бұрын
@@tommygun5.3 I tried the sensor as your video says.. but no luck.. wha else could it be.? 😬😬
@chrisrumph3303 жыл бұрын
Im.having this same issue with my truck
@JaeSweezy2 жыл бұрын
Did you ever find the issue I get the same exact messages
@santiagodavila14262 жыл бұрын
@@JaeSweezy yes. And all related to the same issue.. angle sensor. Goes on the steering wheel column
@mattfreni7714 Жыл бұрын
So there should be a 1 or zero reading for it to be a good sensor?
@wild875710 ай бұрын
I have 06 Trailblazer, scanner shows PCM power control module code P0856 “Traction control torque request circuit”, every now and then I get service traction control scrolling across the dash, any thoughts where to start?
@fireboy5043 Жыл бұрын
great vid i have the same problem right front cant wait to get them abs lights off foreverr lol
@mackredenbarger Жыл бұрын
So on the new Sensors you should just get a “1” which basically means the sensor is not grounding itself out? I’m confused because other videos I watch led said on 200 resistance in ohms meter it should read a high number. When testing “good new sensors” I’m getting the number “1” on my meter as well. I believe I do have a bad abs module as I have verified my body harness connectors are working and no bad wiring
@lfree39613 жыл бұрын
I watched all the videos because I had Traction Control Off, Stabilitrak, Check Engine Light, Cruise quit working, took longer to crank. Random misfire codes....When I finally got to the truck, I added about 4 oz. of brake fluid ALL problems went away.
@jimhinkle72453 жыл бұрын
lol, the ole’ brake fluid will do it every time!!!
@ricardodelaguila35873 жыл бұрын
Nice video. I am having the exact issue on my 2014 Sierra. I have the stabilitrak error along with the traction control light and the ABS light. What’s weird is that it comes and goes. I could have the lights in the morning and in the afternoon they are gone. Next time I get the warning lights I’m going to check my sensors like you did. Just one question, 0 ohms means the sensor is okay right?
@tommygun5.33 жыл бұрын
That's correct. Best of luck.
@tommygun5.33 жыл бұрын
Mr. Del Aguila,, Where you able to determine the intermittent problem?
@ricardodelaguila35873 жыл бұрын
@@tommygun5.3 yes, my issue was the passenger side wheel hub sensor was shot. I went to Autozone and purchased a new sensor which fixed my issue.
@menazco.43962 жыл бұрын
Was your needles on the dashboard going crazy on yours?
@ricardodelaguila35872 жыл бұрын
@@menazco.4396 not that I recall. I don’t have the truck anymore though. I sold it. But after replacing the correct sensor it never did it again.
@tntchitwood2 жыл бұрын
Thanks for the video. I guess I know what I'm doing this weekend.😁
@tommygun5.32 жыл бұрын
Good luck
@Cmanana13 жыл бұрын
Ive seen your video i order all the sensors for my 2011 chevy silverado i replace the rear ones since they were all beat up and the wires were in really poor condition. I have not yet change the front ones. When i change them i will do it ill let you know the outcome and share my experience doing the change. Thank you very helpful video i choose this way instead of changing the one on the stearin wheel.
@tommygun5.33 жыл бұрын
Good luck. Let us know.
@Cmanana13 жыл бұрын
Hello again Friend i actually change all my speed sensor. If i had done what you told me and check every single one, all i had to do was just change one sensor which it was the driver side was the one that wasn’t working because it was broken. I change every single one of them because all Of the other ones were crusty and deteriorating that will avoid in the near future the same issue and all i pay was $28 for both the front ones and $25 for the rear one on amazon. I will upload a video soon with my experience thank you for your video extremely helpful.
@tommygun5.33 жыл бұрын
@@Cmanana1 I'm glad it worked out in the end.
@robertelizondo81183 жыл бұрын
If both my sensors give no readings then they both good ?
@tommygun5.33 жыл бұрын
@@robertelizondo8118 I suggest testing all 4.
@daleh74679 ай бұрын
Thanks for the video, I have a 07 suburban same issue no abs issues though, mine says service traction control and service stabilitrak, just came on while i was driving.
@quetzal13523 ай бұрын
did you find the issue. Im having the same issue on a same truck. 07 suburban please help.
@arleneportsmouth12633 ай бұрын
I also have a 2007 Chevy Suburban and this warning about stable track and traction control started showing about a week after I got four brand new tires and 1 month prior to that I had brand new rear brakes but intended to get the front brakes done but I was told to junk the car by my housemate who told me before I actually was introduced to him that my four tires belonged on his 2004 Chevy truc. He told me it had the wrong battery in it even though it was just put in 3 weeks before from the dealership in St George Utah and so he took it out and he said he threw it in the trash because it was too small to go into my 2007 Suburban and also told me to have it towed to the junkyard because it had a 120,000 miles on it I already spent $30,000 on a brand new paint job and of course all door handles replaced inside and out brand new windows and windshield brand new hood because a meteor hit it and all of the leather seats are basically brand new. Hey strategically parked it right under a tree that has strange glue droppings and millions of birds that have completely covered my brand new paint job in birdshit so now I cannot open the doors because the bird crap has glued them shut and of course been suicidal since I haven't been able to leave the house in 3 and 1/2 years. H e not only disabled my vehicle but he disabled my body as well at least 150 times with broken bones etcetera
@AlexMartinez-yl1ef3 ай бұрын
Mine has those lights on but my dash turns off and ac stops blowing cold air i changed the bcm but it wasnt that. Once the lights come on and i turn off my truck i struggle to turn it on . I wait like 30 minutes and it turns on without any codes till i start driving again
@jolujo5842 Жыл бұрын
I recently discovered this nightmare. Bought what turned out to be a bad tank of supreme gas ... It was contaminated with water. 20 min after the fill up, my engine started sputtering, misfiring etc. I drive a Chevy Express 3500 6.0 liter. The next morning the check engine light came on and the "Service Stabilitrac/Traction control" message appeared. I knew immediately that I had a load of water in my tank. This caused my transmission to start hard shifting into first gear when coming to a stop, my engine to excessively hestitate and balk at shift points, and it completely shut down my stabilitrac safety features. Chevy is CRIMINALLY NEGLIGENT !!! in programming this mayhem into their ECU 😠 After several doses of HEET, two bottles of Sea Foam and 2 tanks of Shell gas, the water was passed through my system. And the check engine light and stabilitrac/traction control messages cleared. YUP...IT WAS JUST WATER IN THE FUEL!!! I feel sorry for the people who are not experienced with automotive mechanics. I suspect that thousands of chevy and gmc owners have been fleeced at the dealership for assorted uneeded repairs. Shame to GM for programming this garbage!!!👎👎👎
@tommygun5.3 Жыл бұрын
I'm glad you were able to get it straightened out.
@jolujo5842 Жыл бұрын
@@tommygun5.3 THANKS Tommy 👍✌
@theusconstitution17766 ай бұрын
Both of my lights have been on for at least a year and about a week ago. I started getting a noise from the left front wheel and within a week I don’t dare drive it anymore. I know I have to change the wheel bearing could that sensor have been smart enough to realize That that wheel wasn’t spinning the same speed as the rest of them because of bearing friction? I’ll find out when I change the bearing.❤️🔥🇺🇸 thanks for your video turned on the lights for me
@tommygun5.36 ай бұрын
Your ABS light coming on is a good indicator that your bearing is going bad. Good luck.
@barrettgranger91392 жыл бұрын
Man I hope this is my problem 🙏🏼 glad I found your video 🤞🏼🤞🏼🤞🏼
@tommygun5.32 жыл бұрын
Good luck! Let us know how you fixed it.
@terryraines99522 ай бұрын
thank you:) need to check mine tomorrow, what's that part you used? from autozone
@pakipower2002 жыл бұрын
Thanks for the great video. I have the same problem with Cadillac Escalade ESV 2016.in raining, few lights get ON, traction, ABS,and the steering gets harder even undeliverable. Do you think these are the same issue and can be fixed by changing sensors?
@rogerp41972 жыл бұрын
I have same issues
@welder91637 ай бұрын
This just happened to me once before with the abs lights and it was the brake pedal sensor. Now to my traction control light comes on and the truck is running like crap, ware the power of the truck goes down, but i also have knocking noise now. Bringing it in to mechanic tomorrow, we'll see. I do want him to check my ground wire and see if it needs to be cleaned. I just don't understand why the knocking sound with maybe a bad sensor? My oil was low but not all the way and i added oil before i left. I will check the brake fluid.
@tommygun5.37 ай бұрын
Good luck!
@AlaskanRobinsonAdventures5 ай бұрын
Did you find anything out?
@E46_2ndA5 ай бұрын
What was the issue?
@theemanofgodalexmartineziv58022 ай бұрын
I changed all my sensors brakes checked fuses and they were good but the abs and traction control is still on.any idea? My GMC canyon only has 65 k miles
@nickschroeder8141 Жыл бұрын
Had the same issues….. I replaced the right front sensor and the hub assembly on my 2011 Suburban 1500... still had the lights and the "C0035 right front wheel speed sensor" code... Replacing the left front wheel speed sensor fixed the issue... How frustrating... Thanks to @ScarabChris for posting “GM truck like a Tahoe, Escalade, ect and it says "C0035 right front wheel speed sensor" then it's WRONG! I replaced the left front and the problem vanished!”......
@TC-ef2pp Жыл бұрын
Can this problem be dangerous? I ask bc my the traction control light came on my 2007 Tahoe in December 2020 while driving approximately 45 mph. Barely ran off the road while trying to figure out the problem. ( not completely only my right tires approximately an inch or 2 in the grass) I clearly remember riding slowly and did not jerk the vehicle. Did as my dad always taught me never jerk the wheel ride it slowly. Have pics of the grass and distance . It’s not an area you would drive over 35 to 45mph. When all 4 tires made contact with pavement I lost total control of the vehicle. To this day I am completely baffled how it was possible. There was no gaining control and watched as I headed into the woods/trees on the opposite side of the road. It was a horrific accident and thankfully I’m still alive. I can’t help but wonder to this day what happened to the vehicle. I know the thought anyone would have is I overcorrected. I know I didn’t and have pics to prove it. It felt like something went wrong with the Tahoe. It’s too late for me, but if this is something that could possibly cause the vehicle to loose control I want to prevent anyone else from what happened to me. Thank God I was alone. I was driving to pick up my daughter when this accident occurred. I know nothing about the stability light and traction light, but did come on and it was in the winter where I live. No ice and grass was damp, but road supposedly dry.
@jeremiahgeneration89102 жыл бұрын
Are you supposed to get a reading on ohms or not? You aren't clear about this in the video, and you show the test for the new sensor when it's not plugged into anything, but you don't show or say anything about the ohms reading when you have it installed and connected to the wire it connects to. I just tested mine and I have a .538 coming up on mine. So, what am I supposed to be getting?
@tommygun5.32 жыл бұрын
Thank you for your question. A good sensor had zero ohms. Hope that helps.
@ScarabChris2 жыл бұрын
Can you confirm one thing? When you tested the new sensor on the right front and the lights went away, was the sensor installed in the wheel hub or just hanging? I ask because I just did wheel hub bearing assemblies on my 2008 Escalade. I had no issues with the ABS and Traction before. But with the new hubs and sensors I get the C0035 code which indicates a fault in the right front wheel speed sensor. Just to be sure I didn't get a bad sensor in the new hub I put the original sensor in that I knew to be working and I still can't get rid of the dummy lights even after clearing the codes with the scan tool. In short I want to know if the lights clear even with the sensor NOT installed in the hub. I want to be sure the ABS ring in the new hub isn't bad causing the issue. If not, then I must have a bad wire somewhere up stream from where the sensor plugs in. But damn I didn't go past that plug.
@tommygun5.32 жыл бұрын
Just hanging.
@ScarabChris2 жыл бұрын
@@tommygun5.3 Perfect thanks!!!!! Now I can be sure I can test without replacing the entire bearing hub assy again. LOL.
@ScarabChris2 жыл бұрын
Ok my issue is fixed. FYI if you have a scan tool on a late model GM truck like a Tahoe, Escalade, ect and it says "C0035 right front wheel speed sensor" then it's WRONG! I replaced the left front and the problem vanished!
@nickschroeder8141 Жыл бұрын
@@ScarabChris 🤠 You rock..!!!! Your are so right on.... I replaced the right front sensor and the hub assembly on my 20110 Suburban 1500... still had the light and the "C0035 right front wheel speed sensor" code... Replacing the left front wheel speed sensor fixed it... How frustrating... Thanks for posting......
@DrJ5613 жыл бұрын
I'm only getting a service stability on mine. Not service stability+ABS light. Could it be something different?
@tommygun5.33 жыл бұрын
I would still start with checking the wheel sensors.
@Hynes98Caper3 жыл бұрын
Hi, have same issue. Service stabilitrac, service 4x4 and intermittently throws abs light. Only thing is when it throws these codes or lights it wont start at all. Pop battery wait 20 minutes truck starts and drives, couple hrs or several days/weeks till codes go again and wont start. Speed sensors you think?
@tommygun5.33 жыл бұрын
@@Hynes98Caper I honestly am not qualified to answer that one. Maybe try a reputable repair shop. God speed
@zolilaporte72113 жыл бұрын
I have the same problem with my 2011 Silverado I have replaced everything one could imagine. Still have the same issue. Just took it to a shop. If anyone has any ideas let me know. Thanks
@James-15383 жыл бұрын
@@zolilaporte7211 There is a sensor on your steering column that might need replacing. This is a known problem on Chevy. Part is about $90.00 if you look on KZbin, it will show you how to replace it.
@joeyfloortom9585 Жыл бұрын
when the stabili link and traction control light came on, did the truck start running like shit? My yukon runs great until the lights come on. its intermittent. thanks
@tommygun5.3 Жыл бұрын
No, my truck ran fine when the lights came on. Good luck
@DrJ5613 жыл бұрын
Can you show where on the plug you measuring reistance?
@tommygun5.33 жыл бұрын
Inside the plug of the sensor are two metal connectors. Place each prong of your tester on those connectors.
@FelNoobs Жыл бұрын
first check oil level i always see this on my tahoe 2007 and when i check oil is very low , i add oil and everything ok
@dravenlively3438 ай бұрын
I was just driving and the stabilitrak and and control service came up out of no where. 2013 Chevy Silverado 1500
@alexthegreat2323 Жыл бұрын
I have a question did your truck stay in park and didn’t go into gear cause this problem ? Cause I got the same problem and I can’t get out of park
@tommygun5.3 Жыл бұрын
That sounds like a different issue. Best of luck
@alexthegreat2323 Жыл бұрын
@@tommygun5.3 found the problem brake light switch man I didn’t know things that simple can cause big problems made me go nuts for 3 days
@ElTayi1992 Жыл бұрын
Thank you for this video
@Guerrero11873 жыл бұрын
Did a brake pad replacement and nowadays service stabila trac So 0 ohms when sensors are good?
@tommygun5.33 жыл бұрын
Correct, that's what I got.
@billalde-dm2so Жыл бұрын
I don't have an ABS light on would it be the same thing as your video is showing
@tommygun5.3 Жыл бұрын
I would encourage you or someone else to use a good OBD2 scanner for diagnostic; not a cheap $20 one. The BlueDriver works great for me.
@adamb23712 жыл бұрын
Hi guys I had the same problem with my truck. I took it to the mechanic and it was my Accelerator Pedal Sensor . Once I replace the part the truck started working .
@Mcnutts32 жыл бұрын
I believe I saw a recalibration fix for that. Ign on step on gas pedal 3 times ign off.
@houstonbrown34507 ай бұрын
Can grounding issues cause this
@zu15028 ай бұрын
Hey I changed the break sensor ,maf sensor , netural safety switch. And transmission speed sensor. And I still keep getting traction control . 08 Chevy Tahoe ltz what else should I change their is no abs light on and the backup camera does not work and you can't see what geae your in until I clear the codes .
@tommygun5.38 ай бұрын
Posable the steering wheel position sensor.
@zu15028 ай бұрын
@@tommygun5.3 won't that have specific engine code
@tommygun5.38 ай бұрын
@zu1502 that will not show up on a standard $20 OBD2 engine scanner. Better scanners can pull up codes for body, 4x4, and ABS.
@syfr2 жыл бұрын
The '1' is infinite resistance , not "0" Otherwise very handy!
@mackredenbarger Жыл бұрын
Is this what you are wanting to see for a good sensor??
@505bullys_N_Lowriders2 жыл бұрын
I have a 2010 Silverado same lights came on after the rear passenger tire I had a blowout on it and them lights came on afterwards trying to figure out what happened here
@tommygun5.32 жыл бұрын
Any luck figuring it out yet?
@holdingcopsaccountable65543 жыл бұрын
My verano did this. Then 0420 code right after crazy shit. I put new top spark plug and so far so good. No code or crazy wrench’s showing up on the screen.
@mtrotts55782 жыл бұрын
I changed a hub bearing now i have all abs stabilitrak and traction control on brand new hub bearing
@tommygun5.32 жыл бұрын
Check your connections and the brake fluid level
@tjhancock27922 жыл бұрын
Same here
@starglider652 жыл бұрын
Abs,Trac off,serv vehicle soon light on..connect obd..turn key to on position..lights on..no codes???
@tommygun5.32 жыл бұрын
@@starglider65 I don't know which scanner you're using. The one you have may only be looking for engine codes. The more expensive scanners can do read more codes. Good luck.
@starglider652 жыл бұрын
@@tommygun5.3 I also have a serv vehicle soon lite..still no code coming up
@marvineffingjones9701 Жыл бұрын
I'm going to try this
@Richard-ge4hj Жыл бұрын
My ABS traction control is blinking also? Any clue?
@tommygun5.3 Жыл бұрын
Check the ABS fuse. Pull the trouble code from the OBD2.
@keithg34012 жыл бұрын
Tried unscrewing mine and it was so tight that I stripped it. Can't get it out now. Any suggestions?
@tommygun5.32 жыл бұрын
I would try using an easy out. Possibly replace the whole thing. Best of luck.
@keithg34012 жыл бұрын
@@tommygun5.3 Thanks so much for responding. I think I'm just gonna replace the whole thing.
2012 is doing this put new ones on both sides and still have the same issue.
@tommygun5.33 жыл бұрын
Did you change the rear sensors also or just the front two?
@Allthingsjilld3 жыл бұрын
@@tommygun5.3 No just the 2 front
@tommygun5.33 жыл бұрын
@@Allthingsjilld I just read in the service manual that low break fluid could also cause warning lights. Possibly check your break fluid. If that's okay then I would look closer at the rear wheel sensors.
@Allthingsjilld3 жыл бұрын
@@tommygun5.3 ok will check. Thank you!! 😊
@er_ikg5653 жыл бұрын
I have the same problem, except my engine power is reduced to low. I went to autozone and they said it was my accelerator pedal sensor. Changed it but the message keeps coming on. Maybe it could be the wheel speed sensors?
@bklynsazon54783 жыл бұрын
I have the same problem like you. Tell me if you took care of it. Curious to know what it was.
@redbeardoff-road17383 жыл бұрын
never trust an autozone diagnosis
@er_ikg5653 жыл бұрын
@@bklynsazon5478 I did actually. Like the guy under me said, “never trust an autozone diagnosis” I changed my throttle bottle out with a new one and returned my the accelerator pedal sensor since it wasn’t the problem. Haven’t had that problem anymore!
@craigerz023233 жыл бұрын
Spark plugs
@holdingcopsaccountable65543 жыл бұрын
@@craigerz02323 that’s what I did. So far so good.
@coyote7030 Жыл бұрын
It can be a bad spark plug,maf so on and so on just a heads up guys
@arleneportsmouth12633 ай бұрын
🤔🤔🤔 So you put a metal clip connected to a strange read device and you touch it to the tire. What is this supposed to do is it testing the amount of tread on the tire ??? That notification came on my panel after I got four brand new tires and it started making a weird noise and quickly vibrate left and right when I would press on the gas pedal an attempt to turn left into a parking lot. Quit driving it right after that because my housemate told me I needed to take it to a junkyard even though it only had $120,000 Mi on it and I am extremely gentle on my vehicles no hard stops and no heavy pressing on the gas pedal and so now I really want to get it fixed because I've been waiting three and a half years for his mechanic to give him a call back which I'm guessing he probably doesn't even have a mechanic because he was really angry that I paid to have it towed to the Chevy dealer cuz he told me that people at the Chevy dealer don't know anything about Chevrolet suburbans. Then he kept taking the battery out so I could never get it to the dealer myself 😢
@bobbymyers8238 Жыл бұрын
What this part is call so I have that problem with my 2007 Chevy avalanche
So is it normal my car wont start and shows a 🔐 lock saids traction control what can i do to make it go on? Please help
@tommygun5.33 жыл бұрын
Did you try to disconnect the battery to reset the computer? May not work but worth a try.
@vickyandhertroublemakers75163 жыл бұрын
@@tommygun5.3 thankyou so much i actully ended up buying a new battery from autozone and is good now 🤦🏻♀️
@brianorluck35048 ай бұрын
Magnetic band inside hub bearing broken was our problem...
@dirtyr1937 Жыл бұрын
Is it and sensor ? Or tire sensor ?
@wild875710 ай бұрын
Speed sensor
@FMChimera2 жыл бұрын
OK, but why/how would a bad hub NOT throw a code for said problem? I have this issue and NO ABS/speed sensor codes...
@tommygun5.32 жыл бұрын
Great question!
@mizaelgarcia1522 Жыл бұрын
I have the same problem with mine, but mine goes on and off
@tommygun5.3 Жыл бұрын
Likely one of the sensors are going bad. A scanner should help identify which one. Good luck
@JulianFRosales3 жыл бұрын
Mine stayed on after changing my struts... Not sure why?!
@tommygun5.33 жыл бұрын
Sounds like possibly a wire or connector.
@dustinwalker85763 жыл бұрын
Did u use original struts or did u convert from air ride struts to conventional? If so you have to wire in resistors
@billydamnit3 жыл бұрын
Same thing happened to me. The sensors are magnetic, so they pick up any little metal pieces. Take them out and clean them off really well, and stick them back in. That works for me. Good luck
@aleaceves21592 жыл бұрын
Having this same problem on my Buick Enclave, already changed brake switch and codes still on!
@rhurtadorh32 Жыл бұрын
What year on the enclave
@MatthewSmith032 жыл бұрын
Mine 09 2wd those same lights plus brake like flash multiple times in a row sometimes it doesn't do it all but after a little while driving it it's like it goes in limp mode and doesn't allow me to shift and it kicks down to like first gear sometimes I can cycle the key sometimes I'd unplug the battery and it'll go away and sometimes it comes back on right away and sometimes not for weeks at a time anybody else have that trouble and what should I go about to fix the problem
@tommygun5.32 жыл бұрын
Sounds like it's going into limp mode. Possibly try BlueDriver OBDII scanner. It's what I use.
@MatthewSmith032 жыл бұрын
@@tommygun5.3 yeah that part is noticeable but ill just have to check the abs sensors bc dont have problem with brakes or anything just while driving some days an others just truck sitting idle lol typical generic made Chevy LOL
@msolis4853 жыл бұрын
Put brand new spark plugs wires and doesn't fixed my problem
@russpeaknuckel95253 жыл бұрын
Nice testing !
@tommygun5.33 жыл бұрын
Thank you.
@israelrico91353 жыл бұрын
Nice nice well done ✔
@leonymax26503 жыл бұрын
Meu cruze está dando dtc c056d
@conradlanders8085 Жыл бұрын
I wish you show us exactly what to hook up the meter to.
@tommygun5.3 Жыл бұрын
Thanks for the input. The two terminals in the plug(s).
@Jason-hm9hr Жыл бұрын
It was a Ford you had to pull out the mud wasn't it ???
@tommygun5.3 Жыл бұрын
Lol
@dirtylu792 жыл бұрын
Would this be the same on a 2wd?
@MatthewSmith032 жыл бұрын
I'm wondering the same thing cuz mine will even go into limp mode and won't let it shift until the lights go off sometimes it works fine and other times it don't