How to set the zero stop and windage on Vortex Viper PST Gen II (2, two).
Пікірлер: 79
@terrysharp502510 ай бұрын
Best and easiest explanation I’ve seen. Thank you
@fod42507 ай бұрын
Hey you’re welcome. Thanks for the encouragement.
@BNatoAk4 ай бұрын
It would be nice to actually see the complete process but I can't blame ya for not wanting to re zero your rifle lol, cheers!
@galactichazzard89324 жыл бұрын
Simple and to the point. I was able to finally get mine done thanks to your video. The idea was to have the turret bottomed out prior to sighting it at 100y. Once sighted (elevation/windage) I tightened the 3 screws and put the cap back on and tightened that one. Thanks again for the video....
@fod42504 жыл бұрын
Thanks! You wrote a good description of the process. All the best with your shooting!
@salvadorvillarreal6375 ай бұрын
Great video, my gasket broke too, but it doesn't seem like its necessary. A little trick I would recomend is to leave about 3MOA or 1 MIll on the elevation instead of locking it out all the way. This is so you don't have to unlock the inner turret if you have ammo that shoots a bit higher and you need a bit less elevation.
@timfodor90365 ай бұрын
Yes, a good thought and I should have mentioned it as I do the same. Thanks!
@shootersara5 жыл бұрын
I watched your video when I first got the scope. Easy peasy. Thank you for the quick video without extra, unnecessary babbling.
@timfodor90365 жыл бұрын
Thanks Sara.
@mrsmjs15504 жыл бұрын
Thanks for the explanation - quick and simple. Much appreciated!
@22guru Жыл бұрын
Thank you
@Brian.Wyant17 ай бұрын
I have done this exact process but it wont stop clicking. I think my scope is defective. Only way for me to get it to move freely is to loosen the top two screws on the turret underneath.
@gerardladalardo13784 жыл бұрын
If you're going to show how to set the zero stop, don't skip steps, show every step.
@MRSILVERTIPP Жыл бұрын
PLEASE HELP IF POSSIBLE I PURCHASED A VIPER PST USED NO BOX NO MANUAL AFTER THINKING I HAD ZEROED IT AND BEFORE WATCHING ANY VIDEOS I KNEW I HAD TO REMOVE THE TURRET CAPS AND ROTATE THEM AND ON THE UP/DOWN TURRET I REMOVED THE 2 ALLEN HEAD SCREWS IN THE TOP FROM THE 2ND TURRET THE ONE YOU CALL THE ZERO STOP THINKING I NEED TO ROTATE IT UPON DOING SO I THOUGHT I HEARD SOMETHING FALL OUT NOT BEING ABLE TO SEE ANYTHING ON THE FLOOR ANYWHERE I PUT IT BACK TOGETHER NOW IT DOES NOT STAY IN PLACE IT ROTATES FREELY NOT CLICKING AND NOT MOVING IN 1/4 CLICKS IF YOU KNOW WHAT I MAY HAVE LOST OR WHAT I AM DOING WRONG OR KNOW WHERE I CAN GET A PARTS BREAKDOWN YES I COULD SEND IT TO VORTEX TO BE REPAIRED BUT I TRULY BELIEVE I LOST SOME THAT I CAN PUT BACK TO MAKE IT WORK AGAIN IF ANY ONE READS OR KNOWS HOW TO FIX THIS YOUR HELP WOULD BE GREATLY APPRECIATED
@22guru Жыл бұрын
Did you figure it out??
@johnpan788 ай бұрын
Thank you for the video, What is the difference between sighting a riflescope with a 0 moa base and a 20 moa base?
@fod42508 ай бұрын
Not much. The 20 moa rail just cants the elevation a bit to give you 20 moa more of elevation once you have zeroed your rifle.
@tonytees75775 жыл бұрын
I'm going with this method. But.... the instructions that I recieved with my scope vary from your video. Vortex Viper PST Gen2 5X25X50.
@SnapD242 жыл бұрын
Wait. So you can't zero your gun where the zero stop is all the way down unless you're lucky?
@CristianCvitanic2 жыл бұрын
Hi, thanks for the video. One question though: I followed your methods and my elevation dial doesn't sit at the "0" mark of the barrel (the scale that counts how many turns you're dialed up) but instead sits at "1", thus removing a whole revolution of elevation adjustment. Is this correct?
@madmagrider2 жыл бұрын
The top cap will show zero once installed. The inner ring will most likely not, but it doesn't matter.
@hitmhard7 ай бұрын
For elevation after zeroing how come mine is on like 2 1/2 and yours is on what looks like 1? That doesn't give me nearly as much to work within comparison to you.
@fod42505 ай бұрын
I have the scope canted on a 25 moa rail.
@hitmhard5 ай бұрын
@@fod4250 Thank you!
@briandorning45375 жыл бұрын
But your zero stop now reads at 1? Its not on the 0 line?
@fod42504 жыл бұрын
Sorry. Hard to line up perfectly as I was filming and trying to not make it a long video. I trust you understand the process? Do I need to explain more?
@grchin3 жыл бұрын
Agreeing with B Dorning... I can make sense of moving the cap so it visually reads zero, but is it possible to adjust the indicator and mechanics to that "0" rotation plane indicator (versus just above the 1)? Can't wrap my head around how enable more slack upward. If this makes sense? 🤦🏻♂️🤷🏻♂️
@Tyler-kt8qz2 жыл бұрын
So before anything I need to turn the first turret cap all the way left till it stops then do the other steps?
@fod42502 жыл бұрын
Yes that is correct.
@ricky2shoez2154 жыл бұрын
Sweet ! Thanks man
@samsam-mf5um3 жыл бұрын
at 1:55 is not making click but still change the zero i try it with laser light
@raymondmichael30774 жыл бұрын
Where do I want my zero stop to be? If I sight and zero stop at 100m, I can't dial in for any target closer, and have to use gradations on the reticle. Is this how most zero stop set ups are intended to function?
@fod42504 жыл бұрын
I think there’s at least 2 options. 1) Set the zero stop to bottom out on zero. Unless you’re a precision target shooter anything less than your 100 or 200 m/y zero will only be less than a few cm’s or inch+/- off. For hunting this really should not matter at these distances. 2) If this does matter or like me you shoot more than one ammo through your gun which has different points of impact, then set the zero stop with some additional margin. I usually allow for 5 or a few more clicks to accommodate the margin I need. I find it easy enough to wind down till it bottoms out (beyond the zero) and then click back the few clicks to put it on zero. Some however would not want this. Did this help?
@raymondmichael30774 жыл бұрын
Fod thanks for reply.
@jaredmoss81703 жыл бұрын
@@fod4250 Answered my question.
@evanwindom32653 жыл бұрын
@@fod4250 That's an interesting idea. Insightful.
@jessecopeland972811 ай бұрын
It is possible to set the zero stop after zeroing?
@fod42505 ай бұрын
Sorry for not answering. Hopefully you solved your problem. I think you need to start with zeroing
@johnschmidt60894 жыл бұрын
I was hoping to see a video of someone actually demonstrating the step-by-step doing of it rather than just hearing someone describe, like, "What you're going to do is ..." without actually describing and demonstrating "What you're going to do." Question: "How do you make pancakes?" Answer: "What you're going to do is get the ingredients and mix them together and then cook them on the stove."
@fod42504 жыл бұрын
Sorry. Was trying to keep the explanation shorter as many folks don’t like to lengthy of an explanation. I hope you were able to find someone else’s post that covered the parts you needed. Thanks for the feedback. I’ll keep this in mind for future posts.
@TjHeuer-ct7eo2 жыл бұрын
So how do you get the zero to the zero rotation position?
@fod42502 жыл бұрын
1) Before sighting it in just turn the elevation left/down until it bottoms out/ won’t turn any more. 2)Then loosen off the elevation cap and remove. 3) Next loosen the 3 internal Alan screws, which will allow you to adjust elevation as you now sight in your gun. So now shoot and adjust the scope. Note it will turn smoothly with no clicks. 4) Once elevation is dialled in then lock off the 3 internal Alan screws, replace cap into the zero position and tighten. This should finish the elevation process. For windage, just turn until it is in line with your bullet placement. Then loosen the Alan screws and spin the cap to the correct zero position and lock the Alan screws. Hope this helps.
@TjHeuer-ct7eo2 жыл бұрын
@@fod4250 it did help but my scope is reading that I have 2 full rotations now on the turret while bottomed out 😅 is there any way to adjust that part? Appreciate your time!
@fod42502 жыл бұрын
@@TjHeuer-ct7eo Do you have a 20 MOA rail on your gun? This likely will affect this.
@TjHeuer-ct7eo2 жыл бұрын
@@fod4250 I don’t but that makes a lot of sense
@fod42502 жыл бұрын
@@TjHeuer-ct7eo Checked my gun and I am also at least a revelation up and I have a 20 MOA rail. I think it just is. Otherwise I’d contact Vortex for their input.
@joejr96535 жыл бұрын
How did you figure out to turn it all the way down first? Does it tell you that in the scopes manual?
@timfodor90365 жыл бұрын
I can't remember if it was clear in the manual or not. I did call Vortex and have a Tech walk me through the process. This is part of what provoked doing this video, because it didn't seem clear or intuitive. I hope this video helped you. All the best!
@jiajianhou4266 жыл бұрын
Why not just zero the rifle and then remove the cap and then put it back on at 0 mark? Is this only to prevent dial in below the original zeroed range?
@fod42506 жыл бұрын
Jiajian Hou, I tried this but it won’t create the stop at zero. You need to first spin it till it bottoms out, then take the cap off, loosen the 3 internal lock screws and then shoot and dial your necessary elevation. Then lock those 3 internal lock screws, and then finally put the cap on in the zero position. It may not make sense. I understand it’s a little confusing. But if you follow my instructions step by step I trust you will find it to work for you. - All the best.
@buddy95776 жыл бұрын
If you loosin the internal screws it doesn’t click.
@jiajianhou4266 жыл бұрын
Fod why do I must turn it all the way down before zeroing the rifle? Can I just zero the rifle like a normal scope, and then lift the cap, and then tighten the inner turret.
@iGOBURR5 жыл бұрын
Jiajian Hou because you want all the elevation you can get if you start without bottoming it out you won’t have as much up travel on your elevation
@fod42505 жыл бұрын
@@jiajianhou426 Try doing it, but I think you'll find it doesn't actually set the zero stop. You need to turn it all the way down first before zeroing as this is what puts it in the "stopped" position. All the best.
@peter93145 жыл бұрын
What???
@savage57646 жыл бұрын
What gun?
@fod42506 жыл бұрын
This particular gun is a Tikka in 300 Short Mag, with a Tac 21 Chassis system from MDT (mdttac.ca/collections/chassis-systems). I've had good results from their chassis' (≤ 1/3 to ≤ 1/8 moa results with my various guns on their platform) and like their new ESS system, which is geared towards PRS type of shooting.
@fredbartlett43942 жыл бұрын
Y would u lock your windage, u need to go both ways
@fod42502 жыл бұрын
Correct. The windage dial will turn both ways, but once you do your initial adjustments to zero both elevation and windage you need to set and lock the windage dial back to the middle between R and L. Hope this clarifies.
@gerardladalardo13783 жыл бұрын
you FORGOT to release the zero stop (3 screws) after removing turret
@billbee2354 жыл бұрын
Just throw away the o-ring LOL
@fod42504 жыл бұрын
Yup.
@buddy95776 жыл бұрын
dont make sense
@fod42506 жыл бұрын
BUDDY CHANNELL It may not make sense. I understand it’s a little confusing. It took a bit for me to wrap my mind around it at first too. But if you follow my instructions step by step I trust you will find it to work for you. - All the best.
@tacox32366 жыл бұрын
Lol
@mattrawlins72265 жыл бұрын
Sure it does.
@fod42504 жыл бұрын
Sorry, remove of the windage cap is actually not necessary. Simply dial the windage as you take your shots to achieve windage zero. Then loosen the 3 Allan keys. The dial will spin freely. Turn until the numbers are set to your actual zero. Then tighten the 3 Allan keys. Done. Hope this helps explain why it is not necessary to remove the windage cap.
@Arsenal125Foward Жыл бұрын
I just got mine, my focus know doesn't turn. is that normal??