Setup Drone Altitude Hold (Baro) and Hover on Multiwii + NRF24

[@ArduJimmy]

Drone without Altitude Hold on is like bread without meat. Altitude hold is a feature on a drone. It is a flight mode where the drone automatically maintains a constant altitude, allowing the pilot to focus on other controls like direction and movement without needing to constantly adjust the throttle to stay at the same height. For me, Altitude hold on my drone is A MUST 🥰

[@yanprata569]

Hello, how can I use it on a larger drone, with a 12v or 24v motor, since the project apparently only allows 3.7v.

[@ArduJimmy]

@yanprata569 sure, I must buy the motors and esc first. wait in a week or 10 days. I'm saving for that budget lol

[@yanprata569]

@@ArduJimmy Would there be some means of contact, I need it for a very specific project, I intended to use a motor similar to a printer (Similar example: CD ROM) 12v or 24v with high rotation, these motors do not have 3 wires, you cannot use esc's.

[@ArduJimmy]

@yanprata569 ESC is Electronic Speed Controller. All drones need ESC. Current project using mosfet + 1n5819 + 10K as DIY ESC. if you see there are two wires, then the motor needs brushed ESC. Note: you can try mosfet : IRLZ44N. diode: MBR1045 resistor 10K ohm please check the AMPERE needed for the motors: if the motors run at 1 ampere, use 1n5819 diode if motors run at 10A or above, use MBR1045 diode if motors run at 5A use: SR540 diode dont forget to add 100 ohm to the ground as a switch at the wiring (please see my githun repo about th wiring where 100 ohm needed) CONSIDER the torque and RPM of the motors to see if it can lift the drone, since I think the motors will be so heavy

[@yanprata569]

@@ArduJimmy How can I make the drone maintain the same position while flying.

[@robotronik2371]

We are waiting for next video pleasz

[@ArduJimmy]

sure. I'm also waiting for arrival of battery. mine was used during 2 years and now need to be replaced. Be patient please 😁👍

[@erpianasolihin8889]

me too

[@JepStockholm-vr6fb]

Me too👍

[@Mediasiswa-y1h]

OMG! Is that so simple??? Really thanks for the tutorial

[@ArduJimmy]

is that so difficult? of course not LOL

[@HASSAN-q5n]

You can make pcb board instead use of more wires

[@ArduJimmy]

@@HASSAN-q5n you're right, I'll make it and provide powerful single board for premium members only (5 dollars/months) in the future plan

[@Xkite51]

Great job you have done here, I have one question, does Multiwii 2.4 have AltHold mode? why use Multiwii 2.3? thank you

[@ArduJimmy]

Actually I want to use 2.4 - mostly people say that 2.4 is the best one. I go angry 🤣🤣🤣 thats why I use 2.3 and modify some code to make it usable perfectly. 2.4 can activate altitude hold. if you watch my video related to bmp180 and bmp280 you will see that activating bmp180 is very simple since it is upgraded module from bmp085. Thanks so much to ALL MULTIWII developers. They are very very WOW ❤❤❤❤

[@Xkite51]

@ thank you for ur answer, god bless you~

[@shortstalkingtomfunny7582]

👍

[@ArduJimmy]

thanks talkingtom 😁

[@potbot887]

Any particular reason for choosing BMP180 over BMP280?

[@ArduJimmy]

no. I choose 180 since it is very easy to implement in our project so that everyone can have a flying hover drone with super low budget

[@potbot887]

@@ArduJimmy okay! Strangely both cost roughly the same online in India.

[@ArduJimmy]

@potbot887 not in Indonesia 🤣🤣🤣🤣 cost means eveything ☠️😬😞

[@potbot887]

@@ArduJimmy no doubt ! Great work on the drone btw. I am in progress of making my own as well. Thanks a lot!

[@ArduJimmy]

@potbot887 nice! I'm here if you have any question 😍👍🔥🔥🔥🔥