SG3525 LM358 PWM Inverter Driver Module 30khz - 60Khz (Part-1)

Hi Friends in this video i will test a inverter driver board from China . this board is used to make inverter and it contains 2 chip SG3525 and LM 358 sg3525 is famous pwm controller chip and LM358 is used for amplifying current signal. and this driver has Push pull NPN And PNP Transistor output stage so it can drive Powerful MOSFETS
Pinouts
1.Output:12-24V
2.Driver current:1A(max)
Pin Description
1, positive power supply
2, the signal output
3, the power anode
4, the signal output
5, optocoupler input positive
6, the output of the optocoupler negative
7, the signal off short legs
8, pulse width adjustment feet
sg3525 module, frequency modulation, lm358 driver, pwm circuit, smps, power supply, pwm design, pwm control, pulse width modulation, sg3525 power, frequency mod, inverter, lm358 circuit, switching power, pwm modulator, pwm controller, smps design, electronics, sg3525 driver, sg3525 tutorial, power electronics, pwm, switch mode power supply, lm358 applications, smps circuit, pwm techniques, frequency modulator, pwm inverter, electrical engineering, sg3525
#Inverter #SG3525 #electronic #sg3525+lm458 #inverterdriverboard

[@Electronic_For_You]

Part-1🔴 kzbin.info/www/bejne/boecqppppM5jZ7csi=q5oVjRgHw0ZdEuWC Part-2🔴 kzbin.info/www/bejne/eZ_XdWqGjdOfjdEsi=ENk4A_b27TiH1JFr Part-3🔴 kzbin.info/www/bejne/bIO8foyqp7xjftksi=Ax0sMIOIGXZcJw_K Part-4🔴 kzbin.info/www/bejne/hZ_SaZutgLF1qrMsi=v8IXgQaiNgE0i-Rc

[@riz23]

if we want 12 volts in rectified output, must there be 5.1 volts in pin 8? I can't find much information about this module.

[@riz23]

(by dimensioning a voltage divider)

[@Electronic_For_You]

Is pin 8 for feedback? I forgot the pinouts, and you should use a Potentiometer for voltage divider so output can be adjusted

[@montugaming4307]

How many voltage want pin 8

[@valtersouzaribeiro761]

Boa noite parabens pelo seu projeto

[@Electronic_For_You]

Thanks 😊

[@nsk6914]

If i use Arduino to control the pwm input will it vary the output frequency

[@Electronic_For_You]

😐 how you will control the input frequency with a Arduino?

[@nsk6914]

@@Electronic_For_You by giving pwm signals

[@Electronic_For_You]

From arduno to Where?

[@hendraz1943]

Sir, to make a PWM assembled welding machine, use the sg3525+lm358 module, is the circuit diagram the same as in the video?

[@Electronic_For_You]

Thats sounds complicated

[@TheKtariq62]

Nice information

[@Electronic_For_You]

Welcome

[@HypersonicGuy-kr2bp]

Very good

[@Electronic_For_You]

Thanks

[@maheshindrasingha5923]

How to select Hz rate for ferrit transformer?

[@Electronic_For_You]

It can be changed by potentiometer

[@maheshindrasingha5923]

@@Electronic_For_You I haven't Hz meter. How to select it 😕

[@Electronic_For_You]

Rotate until the current consumption is low

[@triphetchannel]

Why make a complete connection circuit?

[@Electronic_For_You]

Did in another video

[@torikkalteng1026]

Apakah bisa untuk smps FB regulasi

[@Electronic_For_You]

Without FB Output will be high until capacitors explode

[@kalashnikov_47z]

How to use?

[@Electronic_For_You]

Part 2 coming soon

[@lamminh4656]

Đúng cái mình tìm

[@Electronic_For_You]

It works amazing and also cheap