Sharp LC-70LE733U Reset procedure and voltages measurements.

[@donjaeger2149]

Finally the elusive reset technique. Had 3 blinks and 1 blink. Replaced power supply PCB , no joy, replace main board now had 1 blink and 1 blink. TV still dead. Did the "input" + "Vol-" reset. IT WORKS. shut it off and unplugged it ... Plugged it back in and IT STILL WORKS! I owe you a Beer Thanks... Make that a CASE of beer

[@jaywun0778]

Thank you for the info. You saved the exact TV from becoming e-waste. My parents had many people look at it, and was told to buy a new TV. They were told it would be to expensive to fix.

[@songsofram]

Thank you, Thank you and Thank you for such a wonderful tip.... I had even set up an appointment today to have a tech come at home..... and this morning I found this video that specifically provides an alternate way to reset the power than replacing the more complex power supply/board..... works beautifully and as you right said it is good enough in many situations like mine. Glad you were able to connect those TV repair tips and blend that into a video with such nice explanation that made me reset the TV in matter of minutes. A Big Thank You !

[@admiral37]

Thank you! I just experienced this on a Sharp LC70LE733U. Couldn't figure out why the power indicator light was flashing and the monitor was not responding. Your video along with the permanent fix comment were lifesavers. We use the monitor on a portable cart and it was set up in our Executive Dining Room this morning when I discovered the problem. It worked just this past Friday afternoon when I set it up for today's meeting.

[@vinny3725]

Dude you are the freaking man, thanks bro, yu saved my tv, this fixed it, I couldn't find anything bad on this board, every capacitor and every diod, and transiter you name it, this powerboard was reading ok and I couldn't figure it out, thanks

[@mikelaurie9911]

Hi, thank you so much for posting this video!!! I just had the same issue happen with my Sharp Aquos Quattron 70" #LC-LE7032U, I called sharp today and they had to try some reset buttons and i got nothing, they then referred me to a repair guy. I called the repair guy and told him the issue and he said he knew the problem and had 6 TVs in his shop with the same issue in the last 6 months, He said its not good news and that the Panel has gone. He said that sharp now uses a cheap Panel and this is a common issue, and a costly one. He said best case scenario would be him finding a refurbished panel, that would cost about $2100 Canadian, but none were available, and apparently no New panels were available either.. He told me the TV was basically ready to be recycled. That is when I started doing some research and found your post!!! I tried the rest option you described and it just worked, I haven't given it enough time to make sure it stays working like this, but at least it turned on, which means the screen isn't burnt out like I'm being told. I am still pretty upset with Sharp as I was a big fan of there products up until now, this is my third Sharp TV and my newest, biggest and most expensive costing me over $4k Canadian, after only 3 years of lite use for this to happen is outrageous, Sharp should stand by there products when they find lemons.

[@sammy5358]

Mike, I have the same TV as you and am wondering how is it now ? I was keeping mine alive doing the input + volume thing, but now it is black.....no lights, no power, no nothing........I might try to replace the power supply, I can't just give up on it, it was too expensive. How is yours ?

[@kennyroody]

Thank you for taking the time to pin-out all the voltages. This is incredibly helpful. Have a good one.

[@GrantsPassTVRepair]

+Kenny Rood Good to hear. I was hoping that additional info would be of use to someone since they failed to list the voltages on the circuit board.

[@mwngw]

Dave, my Sharp LC-55q7530 has no external buttons, except for the power button . I tried the same reset procedure but on the remote...still no go. Red light on solid with AC present, press power button, red light goes off, no power up, red light then comes back on. Voltages seem ok except no 5VDC anywhere off the P.S. board, but I do measure 2.7VDC on one pin. Replaced both P.S. board and mainboard, same symptom. Disconnected panel ribbon cable from mainboard, no power...nothing. Can't help but think I'm missing something. Voltages on new P.S. board identical to old board.

[@davidschoenthal8125]

I appreciate the work around fix, thanks! I'm not a repair man, just a frustrated consumer. When my TV started flashing the "Morse Code" for SOS :-) I thought I was done for. My wife searched out this fix online and we were back up in no time. I will mention that this is a "master reset" of sorts, so it clears out everything. You'll have to do the initial setup and channel scan. If you ever found out the permanent fix and would like to share it, please do. I don't lose power often enough for this to be much of an inconvenience, but I would like to know the fix just incase.

[@knopflerfan123]

So what was the fix Wayne was talking about. I have one with the same problem! Thanks!

[@shawnstiefel6845]

That error code means that one of your LED strips is bad or going bad. This reset procedure forces on the tv ignoring the fault. The reason you have to keep resetting it after it is powered off is because the fault code needs to be reset in the service menu. If after you reset the fault and power off tv the tv faults again then theres still a problem with your LEDs.

[@troyhamblet8644]

You were so right! It worked. Now I can tell repairman dont bother.It happened to us at 2 yrs old & I even bought extended warranty.

[@bagus_reparasi_elektronik]

Hi.. im workin on sharp LC-65UE630x, totaly dead, but theres 5v voltage on BU5V connector.. is that BU5V mean Bus5v as you describes? Because therese also pin that marked STB but its 0v voltage.. wich one the actualy standby voltage? Pls advice.. thanks

[@GrantsPassTVRepair]

My apologies but I'm not sure. I would think anything that measures 5 volts with the TV off would be stand by voltage, but I'm only guessing.

[@MindTurd]

As the TV will turn on and off correctly ONLY when the power cord is in all the time, shows some sort of memory setting is being TEMPORARILY held. When unplugged from the mains, the reset you did clears and goes back to silly mode. As TV's don't have a battery for the bios like a computer does, what in the TV would be responsible for holding a new memory setting? Seems like faulty bios hardware. Bios software upgrade or overwrite might help?

[@GrantsPassTVRepair]

You might be correct, but it's beyond the scope of my knowledge. Perhaps someone will see this video who knows for sure.

[@robertcalkjr.8325]

Maybe it's a bad EEPROM? When you do the reset, the CPU rewrites the EEPROM and let's the unit work.

[@GrantsPassTVRepair]

To be honest I'm not sure what caused this, but my customer is happy and he paid me so I'm happy :-)

[@nagendranathnatti]

Definitely a big help and easy to follow. Thank you very much

[@mithunnikiyoutuber5170]

Hi my sharp TV is running, but suddenly my tv automatically off and it was dead condition. I am trying to powe on the tv. Power on led light not working.i think there was a powe supply problem in my tv.kindly help me how to resolve this issue

[@GrantsPassTVRepair]

I produced a series of videos on TV repair you might find helpful. You can find the directory to my videos at www.tvrepairinfo.com/

[@thecentralscrutinizer5105]

Dang, I tried this with this Sharp LC-70C6600U, but no LED comes on.Same symptons, I got 5v bus when plugged back in main board I get a 5v, 13v That PS board looks just like this one too, Wonder if its main board issue

[@verinoandrade1615]

Boa noite meu amigo. Poderia escrever os procedimento para efetuar o reset. Nao falo ingles. rsrsrs. Obrigado

[@samj1012]

so if this case keeps happening what needs replacement? the power board or tuner board ?

[@GrantsPassTVRepair]

It's related to the main board, but there might be a permanent adjustment that goes beyond the scope of my knowledge.

[@samj1012]

Grants Pass TV Repair : i have same issue..tried everything and did not work..thinking of buying a mainbaord but hpping it won't go waste also..never but sharp again

[@hookaburns77]

This just happened to mine. Only mine is an Lc-70le750u and I can't get the TV to reset. I've tried everything but the screen just will not come on. I haven't checked the 5 volt bus. Any further updates on this? I've got a power supply on the way, hopefully it's a simple fix

[@mryvkov]

hey, can you tell me what your issue was? I have lc-70le757U, tried to reset - same error code. Did changing power supply work?

[@jesterraj]

So the main board was the problem? I got the same model same symptoms

[@jeanb2201]

Hi, i have a sharp LC-60LE650U that stopped working when my house got struck by lightning a couple weeks ago. I tested the power board using your tips and determined that the board was bad. I got a replacement power board from eBay and installed it. I checked all the voltage again and everything seems to be the same as yours except that when i press the power button, i get 7.5V instead of 12V on pin 1. The TV still doesn't turn on but the LED at the bottom on the TV has a fast flash and a slow flash. I should mentioned that i didn't check the voltage output to the LEDs. Not sure what these should be reading. Im assuming that the power board i bought is oK since i get some lights but i get worried with the 7.5V. Could that be the main board? Please let me know what you think. I tried the reset sequence and i still don't get anything.

[@edwarddilleyjr.1270]

I'm a tv tech of 45 years experience tryed the reset screen never lit an whent back to blinking light thinking bad power supply or driver board?? Any help is appreciated thanks 😊 Ed dilley

[@ralphtricoche7803]

Hi, I want to replace the HDMI port on my Sharp TV LC-70LE733U. Where and what part should I buy? Ive been looking this info and I'm stuck.

[@GrantsPassTVRepair]

You can find them on ebay. Use the key words replacement hdmi ports. They all have different mounts. You will need to study the pictures to find the correct one for your PC.

[@tubejim101]

Are you going to submit that model and your fix find to the book?

[@GrantsPassTVRepair]

I mentioned it to Mike for his next edition of TV repair case histories.

[@MindTurd]

Technically it's not a "fix". It's a work around.

[@GrantsPassTVRepair]

Yes I agree. Technically it isn't a fix, It's a main board issue, but I'm sure those who enable their TVs to come on in this way will still be grateful for the info.

[@jesscee7539]

Thanks for the Video. It helped me on model #LC-70LE632U.

[@bapmami]

Yes I did try that volume thing, it didn't work. My TV is 2014. If it blinks 2x then pauses and blinks 5x or vice versa.

[@erikmendez6081]

Have the same issue. Any luck?

[@williamrayburn9403]

The procedure you're using is a forced power on procedure and you're missing just a few critical elements to resolve the problem. After you have the "K" on-screen press vol(-) and ch(-) together. This brings up a service menu. Then scroll down to "Lamp Errors" and reset. That's why turning it off and then turning it on normally again you're back to the error. After doing that update your firmware. Sharp was way to critical about lamp error detection and under certain circumstances the counter gets added to without detecting an actual error. CCFL lighting, for example, can cause premature error detection. There are some with the 1-2 error that are actually a problem with shorted leds in the lighting array. If forced on does not work I would suspect one or more leds have shorted. To replace them I would strongly advise taking it to a qualified technician.

[@GrantsPassTVRepair]

Thanks for the info but part of the text in your message is hard to follow. Perhaps you can edit it.

[@williamrayburn9403]

Sorry, when it posted it took what I put in brackets and warped them somehow.. After the force on procedure a "K" appears on-screen. Then press, together, volume down and channel down to get to the service menu. Scroll down with using the arrow keys on the remote, to "Lamp Error" and reset. Now the unit should turn on/off normally without having to again force start. The last thing is to update the firmware. Sharp, on many of their models with this problem, have readjusted the sensitivity to lamp error detection to help eliminate the problem in the future. Hope this helps!

[@GrantsPassTVRepair]

Thanks for the information. I'm sure many will appreciate your additional info.

[@robertfornwalt7653]

is there any other way to get to the lamp error screen or reset it? i followed your procedure and before i got to the part were you hit channel and volume my tv came on to it's home screen. but if i can't turn it off.

[@williamrayburn9403]

Unplug it, allow it to sit for about 60 seconds and simply begin again. It is an active button control for that reason. One of Sharp's better ideas. Just try and minimize the time between the "K" appearance and entering service mode...

[@javiergalaviz5649]

Ase 4 blinks mi tv 70 pulgadas cual es el problema

[@harjindersingh-jj4iz]

Thank you so much the same thing happened to ours!

[@pennyweber8999]

You are the greatest! Thank you for your help!

[@MRJWC2332]

bush alba sharp linsor luxsor sets seem to have this problem . I have 4 sets here all different size's and makes but with the same fault . plug it in touch the buttons come on all working fine picture remote dvd etc etc .... but once you unplug dead just random flash code on the front. I think the same as mind turd bios problem could this be the next big problem ie 1st caps 2nd panels now this? but hay if they did get it right we wouldn't be here writing this..... :-)

[@GrantsPassTVRepair]

Was the reset on these other TVs you mentioned done in the same manner as this Sharp where you press the input select button and , volume down button while plugging in the AC cord?

[@MRJWC2332]

Grants Pass TV Repair no just switching on and off numerous of times until the set came on but not on all some was only on the remote then buttons on the set very strange I think these sets are getting worse bring back the good crt's

[@robertcalkjr.8325]

Do they use the same EEPROM's? Maybe there are some bad ones being used. Just a guess.

[@GrantsPassTVRepair]

I don't know if they use the same EEPROMs.

[@andyfunk9262]

This worked for me, thanks for the tip!

[@BrandonGarbutt]

Sharp 70inch aquos lc-70ud27u Menu and down volume

[@brianspence3367]

i'm having same issue with lc-70ud27u. 2-5 blinks. changed the power supply board. i can get the blinks to stop but no display on tv. any sugguestions?

[@erikmendez6081]

Same here 2 slow blinks 5 fast

[@adrianpena9063]

Didn't work on my TV it turned on then quickly turned back off 😣

[@matthewsanchez6881]

After trying to reset the Sharp 70 inch TV. I do get the flashing logo on the sharp I held down the input and the down button on the volume and plugged it in . I still get nothing the light continues to flash and I don't get anything on the screen, What does that mean?

[@erikmendez6081]

Let me know if you find anything out. Same issue.

[@brig.4398]

Not easy to fix these new sets, no voltage charts on the board and often service manuals are hard to come by.

[@reinaldofraga2638]

credible its work. i proved in lc70le745u and its working ok

[@geojor]

good technical tips...

[@paulhoeger9798]

Thank you this did help me.

[@robertcalkjr.8325]

Thanks Dave.

[@808goblin]

DUDE! THANK YOU SOOO MUCH!

[@shahzishahzi2005]

I'm waiting

[@erikiniguez5260]

I love you!!!!!! my tv works!!!

[@shahzishahzi2005]

Sharp LC42D85U mather bord and tcon and remot is avilibal I'm from Pakistan

[@Chu3505]

Sharp TV Corp.have this kind of problems in it TVs for awhile now in their design flaws for there main CPU chips for their main mother board for either LCD or LED TVs.Have same kind of problems they both have bad firmwares programing problems put into them for LCD TVs design it was OPC and POWER lights together flashing too same kind of deal must unplug reset too.Even that you change another refurbish main mother board still will happen,if the main mother board never receive a software firmware upgraded.Only correct upgraded the firmware will solved this problems,but Sharp Corp.stop letting people doing this already.If you download wrong firmware or corrupt firmware files for the TV will stop working all together can't even do any resetting to the TV anymore either.I own two sharp 46" LCD Aquas TVs. I known this problems for sharp TVs for years.Just used the TV everyday like for 4 hrs a day this problems will never or hardly shown up at all.

[@su1973d]

Thanks it's works

[@hectordiaz5940]

I have a sharp aquas lc 52 in tv. What can I do about a blue power breaking light and, a yellow ocp breaking light?

[@zaprodk]

Oh, /please/ turn off that image stabilization, it makes me sea sick - i'd rather have a shaking video ...

[@GrantsPassTVRepair]

In this case it's necessary to use due to excessive camera shaking.

[@zaprodk]

Grants Pass TV Repair OK ... I watched the video to end but it was frustrating - I don't like the way KZbin stabilizes stuff.