If you have room outside the shed, put compressor out there and run lines in, build a little shed/roof for it to keep out rain…will reduce the noise levels inside the shed while on, also get room back under bench.
@Trailandflow3 жыл бұрын
Perhaps foil backed insulation bats. Much cheaper, will take the echo away, much more resistant to sparks & will help the shed not be a sauna.
@RoamLyfe3 жыл бұрын
I’ll look into them!!
@bumthundy46312 жыл бұрын
@@RoamLyfe also look into foam board insulation great cost/area ratio mainly for heat insulation but great at sound insulation too i run it in my shed
@spirudargon535 Жыл бұрын
I've been a builder for many years and have seen quite a fair bit of sheds. The plans in ryan's package kzbin.infoUgkxB7IXYxLzb_Ichhe45zM3Im5xfEiSp9vB have some of the nicest looking sheds i've seen in a while.
@lachlandunn39743 жыл бұрын
Great episode and the shed looks great, but I don't know how safe all that sound deadening would be around all the sparks and welding slag.
@RoamLyfe3 жыл бұрын
Yeha that’s a solid point mate, I’ll see how it ignites and I’ll check something up on that wall to protect it from the sparks!
@lachlantaylor4583 жыл бұрын
Was about to say the same thing, taking about the camp gear not wanting to catch on fire and then putting soundproofing where the metalwork bench is. Hopefully it’s alright tho good looking shed
@cpp1703 жыл бұрын
Lachlan Taylor put some 0.6mm sheet up behind your welding bench. That will stop the sound proofing catch fire, will make it easier to keep clean and give you something to attach shelves/hooks to.
@jaketreasure5254 Жыл бұрын
You should add splash backs on your benches… the best thing I have done
@talesfromthebottle63143 жыл бұрын
Now you have 6 metres of bench space for all your tools to explode out of your toolbox never to be found when needed
@RoamLyfe3 жыл бұрын
Bahaha legit!
@lukeclarke80542 жыл бұрын
That gel blaster rips I’ve got the same one. I had the rifle one on a table during a rental inspection and the chick threw a tantrum over it. Tables look mint.
@brycycles952 жыл бұрын
My garage use to have over 36 feet of bench space. It wrapped all 3 walls of the garage. This winter I’m going to be cutting it back to only 8 feet of bench space and installing some shelving and getting a big filing cabinet for storage. I’ve found the more bench space I have the less organized it ends up getting
@benchesworth93943 жыл бұрын
Hey mate if you’re going to run hard lines for air through your shed, should build a little roof in the funny corner outside your shed and put it out there, keep noise down when filming and also gives you some more space. Love the content
@peppipoohductionswakashunt315711 ай бұрын
You should sheet the full wall with ply, that way you can hang stuff where ever you want, how good are titans
@liamcan32623 жыл бұрын
Hands down one of the best things I invested in was a band saw. You can cut so accurately with it and it makes life so much easier. I can’t remember what it cost me ($600 ish?) but it was from total tools and cannot fault it. I will never touch the old droppy ever again! Also move the compressor outside. Built a little box for it with those foam sound pads and thank me later. Those pads will catch on fire for sure near where you grind.
@krayziemike173 жыл бұрын
Definitely build your own stand for the bench grinder. An old steel rim, a length of pipe and a piece of heavy plate will do the job nicely. Way more useful being able to drag it out to the middle of the shed if needed.
@RoamLyfe3 жыл бұрын
That’s a great idea, thanks heaps mate!!
@krayziemike173 жыл бұрын
@@RoamLyfe Also with the Bandsaw vs Drop saw debate, I would go Bandsaw everytime. Bandsaw will cut everything the drop saw will, but has the added functionality of being able to be used in the vertical position with a table, so you can push thinner material through the blade, like cutting curves in sheet metal
@teamd57a263 жыл бұрын
Good idea 👍🏽
@mickhuggett23293 жыл бұрын
I brought a makita cold cut saw for $730 at total tools, very little sparks, cuts like a warm knife through butter, I’ve done 5mm plate but wouldn’t recommend it on the standard blade; buy the heavy duty blade for that, but apart from that extremely happy. Cold to the touch immediately after cutting, very little burs, clamp and angle adjustment mechanisms are great. Not a single complaint.
@RoamLyfe3 жыл бұрын
Wow great to know I’ll look into them!!
@mickhuggett23293 жыл бұрын
@@RoamLyfe if you want vids or whatever I’ll flick them through. Brought it to build my tray and more metal work later on and it cuts 50x75x3mm in like 6 seconds, only thing is real loud come to think of it.
@RoamLyfe3 жыл бұрын
Yeah the band saw us so quite to use, have you broken a blade yet? That’s my other concern!!
@mickhuggett23293 жыл бұрын
@@RoamLyfe nope and havnt felt like I’m close, they’re supposed to last ages but I’ve only owned it for ~8 months (though it’s had a LOT of use during that time) I think you just gotta make sure not to push hard, just gently and it cuts so easily. I’ll send some videos and show you the quality of the cuts tomorrow.
@drivewaycustoms37673 жыл бұрын
Workshop goals right there, all you need is a tube bender for barwork! The sound deadening definitely works
@SchysCraftCo. Жыл бұрын
😮. Very nice work. Really looking real good. Keep up the great craftsmanship and hard work my friend. Fab On. Weld On. Keep Making. God bless.
@workingmansrestorations70713 жыл бұрын
I built pedestals for my vice and grinders so i can move them around and possibly outside if needed
@ligma49073 жыл бұрын
Have a look into some Foil boards ! Bunnings has them, Also should look into a cheap white board ! To write down a to do list, magnet instructions or stuff to & even to write down ideas! Just a thought mate as I put one in my shed and definitely helps me keep track of shit on the good ol to do list !
@matthewazzopardi41053 жыл бұрын
Hey Dude started watching recently and love the channel especially the shed eps, a pointer for the benches, you are going to go crazy after a while when things roll off the bench and fall behind it because of the gap between the steel frame of the she and the tin, so get some sheet metal as high as you want and put it as like a backboard so that things dont roll off, also i have a metal drop saw and i love it for cutting steel box section or angle iron. keep up the great work bro!!
@louisomalley13943 жыл бұрын
Great layout. The bench space is a good for a couple of projects at a time. Keeping it clear is the challenge. Looking forward to episodes.
@SHOCKcustoms3 жыл бұрын
Minticle job fella. A very worthwhile upgrade is insulating the remaining walls and roof, kerp it cooler/warmer makes it way better to working. Also helps suppress noise. Cheap insulbatts from bunnings and youll be frothing wet dreams for days! Love the channel minty man
@workingmansrestorations70713 жыл бұрын
Work benches look good. I have a 2 car garage for now till i build my big shop. So storage and organization is big for me. I have a lot of tools and had to store all of them
@TJANDMAC3 жыл бұрын
Getting jelly of this shed setup haha!
@RoamLyfe3 жыл бұрын
Have to have you legends over for a shed session one day!
@rumbear1013 жыл бұрын
put a little garden shed alone the side of the big shed mate to store your compressor and run the hose into the shed. it will give you more room and have the noise thing out side
@ryanwebb7113 жыл бұрын
The milwaukee M18 Bandsaws are pretty sick. Good for mobile work and your can set them up to be a bench drop saw or a table bandsaw too.
@blkstang832 жыл бұрын
You should do the rest of the sides with sound material, to bad you don’t have red ones. You could put the drill press on a stand at the same height as the bench so that it flows better. Nice clean up.
@whoishoogan91503 жыл бұрын
Definately go with a mitre saw. U can cut all sizes of material and it is simpler to use
@orringe42423 жыл бұрын
Get some rubber sheeting and epoxy or staple it to the tops of the benches, protects the bench and pieces you're putting on the bench, holds nuts n bolts in place, and looks good when done right
@logan.vanderbeck3 жыл бұрын
The Evolution EVOSAW380 was one of my best investments. Its a cold cutting saw that doesn't produce the sparks that a normal chop saw would. One of the best chop saws on the market imo
@RoamLyfe3 жыл бұрын
I’ll check it out mate thanks
@Catiec001 Жыл бұрын
Big difference in sound quality 👍👍
@rorymyers53023 жыл бұрын
Pretty mint Diesel is so funny
@RoamLyfe3 жыл бұрын
Haha he’s a little legend hey!!
@eliottmack94032 жыл бұрын
You should put some boards around the back of the benches so you don't have stuff falling down the back and having to pull everything out to get to it
@aussiegeniusaffiliate3 жыл бұрын
Awesome gel blaster mate
@victorshaw71733 жыл бұрын
I suggest putting the metal working closer to the opening of the shed for easy cleanup and bringing in materials. You can make one long bench so you can also cut long pieces of raw material. And a carbide chop saws are nice but are noisy and shoot metal shavings. Also recommend a thick steel plate for your welding bench.
@usrr.artzzz3 жыл бұрын
shed do be looking good, nice job Tom.
@302esky3 жыл бұрын
Band saw from Hare and Forbes about $700 and i used foilboard from Bunnings for insulation
@stevendouglas65933 жыл бұрын
For sound deadening, maybe you could use the fibreglass sound deadening/thermal insulation sheets from Bunnings. Install them between the sheds studs and put thin ply over the top, attached to the studs, to retain and cover them. It would mean you would have to buy a wood saw though. Watching you cut the ply with a grinder was, interesting. Enjoy your channel and the shed is looking good.
@cameronrees90633 жыл бұрын
I have a diamond cut saw( cold cut) and its a ripper mate. Bandsaw will obviously be a bit more accurate but you learn to be with the cold cut saw and its extremely quick and neat cutting as long as you have a good blade.
@nisisjwjshdej19893 жыл бұрын
I reckon you should put some hooking rails on the tray for strap ratchets
@harry12643 жыл бұрын
Wouldn't recommend the foam in ya metal work station as the sparks could melt it and catch on fire
@RoamLyfe3 жыл бұрын
That’s a pretty valid point haha I didn’t actually think of that! I might get a sheet of ply and just ply that side with the foam behind it!
@adamblundell64023 жыл бұрын
A cold cut saw for sure. So much faster then a bandsaw
@charliedavis19703 жыл бұрын
cold cut drop saw goes alright
@harrynewport91893 жыл бұрын
looks awesome, id be careful about that metal work bench though, having timber bench top skinned with steel, welding ontop of that & getting it hot will probably burn and catch fire to the timber underneath, only saying this because ive had it done to myself at a mates 😂😂😂
@MicahBell_18603 жыл бұрын
An organised workshop is the sign of a sick mind. Giggles Bench grinder on a portable stand. Maybe a sheet of ply & sheetmetal between the welding bench & the toolbox? It's good that you have a fire extinguisher handy right next ti the foam panels backing your welding bench. Nudge nudge, wink, wink I got 2 Makita drop saws for $50 each. 1 with a steel cutting wheel & 1 with a wood circular saw wheel. Its g
@ZaneFitzpatrick Жыл бұрын
love this set up👍
@TheAlfador3 жыл бұрын
I would put a metal sheet barrier between the metal working table and the tool box thats taller than the tool box. No need to worry about splatters and sparks
@theandrewchrist2 жыл бұрын
Love the setup! How about a full length over head shelf above the benches for camping gear, parts etc?
@RoamLyfe2 жыл бұрын
That sounds like a bloody good idea mate!
@theandrewchrist2 жыл бұрын
Cheers mate!
@robsdeviceunknown3 жыл бұрын
I dont know how so many get by without temperature controls. I would have (and did on mine) insulated it and then put plywood for the first 8 feet all around. This gave me strong secure walls that I could hang anything anywhere. And it's heated and cooled cost effectively.
@manggang30903 жыл бұрын
1:19 the bogan bus was in the shade and i got excited thinking it was dual cab chopped
@chrisalston57723 жыл бұрын
If you setup outlets for the compressor put one at the roller door
@Shayno923 жыл бұрын
Very jealous of your motivation, I've had my shed for 1.5 years and still don't even have power 😅
@ItzTommie3 жыл бұрын
Sounds better already and looks a bit better! was little worried about the sparks but seen theres already a bunch of comments on that , I would suggest maybe going to a high grade insulation in the ceiling atleast if not the walls as well and maybe even lining the wall/s with yellow tongue and painting it , allowing for ya to build shelfs and hide insulation, keep the heat down during summer and removes a bunch of echo
@achilleaustin3 жыл бұрын
Bandsaw or mitre pretty much depends on what you're planning to do with it. A miter's probably pretty good for ya as most of your metalwork is with tube. But a bandsaw is much better for cutting through thicker pieces such as lengths of bar for lathe or mill work. I'd definitely go for a mitre for about $500 with a steel blade as any bandsaw that cheap wouldn't be too high quality anyways. Loving the shed videos mate, keep it up
@gurdeep.singh39993 жыл бұрын
put the compressor outside and build a little box for it and run the air line through the wall
@James.robiinson3 жыл бұрын
lighting is mint!
@jessetink37533 жыл бұрын
Sheds looking mad bro loving it 😊
@johnpintarich81743 жыл бұрын
Have a look on youtube at the Evolution cold cut saws, don't go with anything that has cutting fluid not to be confused with cutting oil the white stuff if you dont clean it regularly it becomes toxic.
@bigstickerperformance66703 жыл бұрын
Surprisingly that small amount of sound deadening does make a difference 😲
@johngiannakos48733 жыл бұрын
Lessss goooooo . Nice work
@TyesFishingAdventure3 жыл бұрын
Should keep the fold out tables and make a slide on the patrol for it for when you go out camping
@RoamLyfe3 жыл бұрын
One will go on the trailer build! Other Probly in the bin at this point hahahaha
@brendanscott44573 жыл бұрын
Looks good man but I don't recommend putting foam insulation in you're hot works area only because there's a chance of melting them or even starting a fire if sparks or spatter hits them
@TheCozzybear3 жыл бұрын
Hey mate, for your saw look at the evolution compound mitre saw from total tools. Multi material blade, speed adjustable for different materials, and only around the $500 mark. Can't go wrong 👌
@callumwatt63873 жыл бұрын
I found compound mitre saw works great but take the wood blade out and put a tungsten carbide metal cutting blade in
@interceptor7905 Жыл бұрын
How do you like roll cab and top chest?Any good?Probably the best solution for your need would be Hare and Forbes Machinery house tool shop.
@tyjohnson42793 жыл бұрын
1:10 the bogan buss looks like a twin cab 😉😉😉😉
@jakhog89303 жыл бұрын
Great vid I think you should get a Mikita cold cut mitre saw because I have one and it thick steel like it’s not even there and they take no maintenance apart from a blade sharpened like every 18 months
@haydnking76403 жыл бұрын
Cold saw mate for sure.
@RoamLyfe3 жыл бұрын
Cheers mate!!
@braydennicolai66093 жыл бұрын
Hey mate for the band saw get some thing like a makita or Milwaukee hand band saw and the buy a wall mount for it goes real good
@michaelclinton713410 ай бұрын
very nice job on workshop
@DavesShed3 жыл бұрын
Love the video. I am curious why you didn't insulate the shed. You can never have too much bench space. I made an assembly table and used 2 layers of form ply for the top . It has worked great. Take a tip from a QLD woodworker - you need to pull those benches out and seal all the cut ends of the form ply. If you don't moisture will soak into those ends and your nice flat bench tops will no longer be nice and flat. They will act like a slow sponge to absorb water from the humid QLD air. Which for you is a big problem because you have permanently glued them to the frame. You can get a proper wood sealer product but you don't need that. Just paint them with whatever you have lying around ( I had some left over polyurethane). If you don't have anything suitable just shop for the cheapest thing to coat timber. Could be an undercoat, something on sale at ALDI, whatever - just a couple of coats of something is probably enough to stop the ends of the form ply soaking up moisture.
@niallcrawshaw48313 жыл бұрын
Cold saw is the go 👍👍
@curtiskane37813 жыл бұрын
Have you thought about using a big hole saw and cutting a hole out of one of your benches and dropping in your drill press, I did it with mine and its so good. The bottom plate should just unbolt off. Sick content btw, been watching for some time, learnt heaps.
@stevenloynds12863 жыл бұрын
I have in the past use old fruit styrofoam box lids, covers a larger surface you can find them free usually disposed at the back of the markets and obviously fruit and veg shops also will stop you from cooking in the summertime and not that you have to worry about keeping warm in qld but will do that to to a degree too. Should work with your sound I'm thinking.
@tinnedanger3 жыл бұрын
Insulation and a vapour barrier in the roof .. Condensation isn't good for car bits. There's a really cheap thin plywood with a wood grain finish . I used it to line my shed it made a heap of difference.
@bonniedobkin69483 жыл бұрын
Great VIDJA’s 👍🏻
@austenmoral67773 жыл бұрын
I reckon a massive Roam Lyfe flag !! That’ll be sick 🤙🏽
@dwadrop3 жыл бұрын
Could hear an improvement 👌, ply sheet on the wall would help absorb sound and can easily mount stuff to it if needed 🤷♂️
@jamescowell16303 жыл бұрын
Bosch cold cut saw. Awesome saw for the money. Comes with a 6 year warranty
@aa999xyz3 жыл бұрын
looks great, lights directly over workbenches? That foam behind the welding area will melt
@jasontaylor78373 жыл бұрын
I used 25 mm threaded water pipe for my compressor worked well
@monishsharma80533 жыл бұрын
This shed has come so far 😍
@brentmcd123 жыл бұрын
looks ausome !!
@RoamLyfe3 жыл бұрын
Thanks mate!
@flowers6373 жыл бұрын
Awesome Bro, well done, shed looks epic 👍
@JwOcean3 жыл бұрын
Check me out bro
@andrewheadland503 жыл бұрын
Sounds better with it
@jyesmx250r33 жыл бұрын
One grinder spark to that sound defender and you going to need a new fire extinguisher
@garyschopshop3 жыл бұрын
Pro tip for the pegboard, drill out some 6mm holes (I think they were 6mm) and put some M6 bolts through each other and it won't ever move! Love the videos mate 👍🏻👍🏻
@RoamLyfe3 жыл бұрын
Ah great idea I will do that!! Thanks mate
@mrdrifta87553 жыл бұрын
looks sick man if u want better sound u should gyprock the wall with some inso
@lgdrarkyy37533 жыл бұрын
oath brother it sounds mint, and my god that patrol is buttery smoooooth
@darcyhouse79296 күн бұрын
Hey mate how do you find the flake floors after a few years of work especially the welding?
@mxnation99123 жыл бұрын
Hey just a heads up your fake eotech holographic sight on that air soft gun is backwards lol.
@xtu15x342 жыл бұрын
Just out of curiosity mate, how big exactly is your shed? Cheers
@RoamLyfe2 жыл бұрын
6x7.5
@jasonsampson9163 жыл бұрын
Put the compressor outside if your running hard lines
@RoamLyfe3 жыл бұрын
I was going to when I get the side coverd! Might not be for a while tho 😩
@DKHEPG3 жыл бұрын
Hope they’re fire rated for sparks 👍🏽
@HJZ75driver3 жыл бұрын
Pull the compressor apart, mount it on a frame, then put it up in the roof with a hose reel. See Hackshop on youtube for info
@RoamLyfe3 жыл бұрын
I watched that last nignt funnily enough! 🤘🤘
@HJZ75driver3 жыл бұрын
@@RoamLyfe Wasnt sure how to word it 🤣. Unless you saw it, you think i was being obtuse
@fiapritchard9053 жыл бұрын
Put the cupboard in between the book shelf looking things… idk maybe you can use it as a partition to seperate between the types of things you’d wanna put on the shelves
@fiapritchard9053 жыл бұрын
I kept watching you kinda did that ahaha just in a different way
@RoamLyfe3 жыл бұрын
Hahaha!
@fiapritchard9053 жыл бұрын
@@RoamLyfe hey you ever wanna paint a lux the grey you got lemme know ahahaha Love the content so educational for someone like me who know fk all Look forward to the next one bull
@zacwright67873 жыл бұрын
Uses gards and a grinder to cut wood, gotta love that 🤣 livening the content bro keep it up💯
@inspire4x4jacko673 жыл бұрын
Normal old drop saw my brother. And buy a ebay built pipe notcher there handy as. Make a stand for ya bench grinder. And keep ya drill press the way it is. Its handy as to have them mobile. Ya dont wanna be standing in a corner with a bench grinder going. Mulitple air outlets wouldnt be good just get one retactable line and have it central. The roof is a good spot so ya pulling the line down not around on the floor.
@RoamLyfe3 жыл бұрын
Thanks for the tips mate, very much appreciated!
@inspire4x4jacko673 жыл бұрын
@@RoamLyfe no worries bro. Keep that trailer build coming im going to start my own soon
@Rileyfletcher7713 жыл бұрын
Get a pipe notcher if u want to do rock sliders and bull bars
@RoamLyfe3 жыл бұрын
Will buy one ASAP! Cheers
@zappazappa49392 жыл бұрын
Mate how flammable are those sound deadening mats Also put your flammables as far away from your welding
@rickfletcher84223 жыл бұрын
Cold saw is probably going to be more accurate than a bandsaw when you’re talking budget options. I use a normal hot saw(abrasive wheel) but cold saws are cool if the blade lasts a while
@Horsey12952 жыл бұрын
How do you like the Maxium tool box? Super keen to hear your thoughts. They are the only reasonably priced large toolboxes but not allot of people have then.
@RoamLyfe2 жыл бұрын
No complaints at all mate!! I’d buy another one in a heartbeat 🤘
@Horsey12952 жыл бұрын
Where did you purchase it from? I can only find JustProTools that stock them but they are sketchy with stock at the best of times
@RoamLyfe2 жыл бұрын
I think I got it off them! I had it deliverd to my workshop with a forklift!