Sheet The Wing

Part 5 - Sheeting a Pattern Plane wing with balsa - Getting ready to Vacuum bag the wing.

[@joedunnaway]

Hi Dave... I usually install aileron hinge line as 2 quarter inch pieces in the foam before I sheet the wing. I mark the hinge line with a T-Pin at each end of the hinge line, cut off so they just protrude through the balsa skin. After the sheeting glue has dried, you can line up a straight edge with the pins and cut through the skin on both sides to free up the aileron.

[@aircreative]

Hi broo.use wayer for whats?

[@jdj62464]

What brand and type of glue do you use?

[@gripchion]

Good job Joe!

[@tzachus]

Dear sir lovely work, how do you conect both half wind together with dihedral?

[@ginoalongi1374]

ciao Joe, what brand and type of glue do you use?

[@redbaron1954100]

is balsa sheeting a couple of pieces glued together

[@jaimecrespimiralles2685]

Hi from spain, what kind of glue do you use in order yo joint the balsa to the foam core ¿?

[@user-tk9ug2rj3z]

ចង់ធ្វើយន្តហេាះដែររៀននៅណាពួ

[@davidsanford4079]

How do you create, prepare, and install the control surfaces on your balsa covered foam core wings?

[@Dionatronics]

Great video, thank you for uploading it! Couple questions....What kind of fiberglass and and casting resin are you using? What are you going to coat the balsa with?

[@joedunnaway]

The wing can be fiberglassed and painted after sheeting but I usually cover the wings with Monokote. The wing shown in this video ended up weighing 11.9 oz with a JR 9411 servo and linkage (Ready to Fly).

[@lookylou6333]

can the wing be repaired after a crash if the 2 halves fit ? if so how?

[@joedunnaway]

The carbon fiber is .007 unidirectional carbon laminate available through ACP Composites.

[@NickSmith-hv9zi]

I have a set of similar foam balsa covered wings. Too heavy and wounder if there is an easy way to cut holes to lighten the wing.

[@wdlima]

What material is this dark that you cut at the beginning of the video? thanks..

[@XFBO]

carbon fiber veil, lightweight material that adds a bit of strength to wing.

[@changoav1860]

what glue do you use?

[@Chris-vc1dh]

what glue is that please?

[@dirkgrobler2179]

Where is the rest of the video?

[@marceloferreira6563]

friend you make helicopter blades? you send pro Brazil? I'm crazy wanting one of these

[@giffy5775]

3:03 balsa dust cough, I know it well.

[@redbaron1954100]

what is thickness ok balsa sheeting

[@kmekrine1169]

What kind of carbon fiber material are you using?

[@joedunnaway]

The Carbon Veil weighs .3 oz per yard and is available through ACP Composites.

[@ThomasGreenhill]

What thickness balsa is this?

[@camaro92026]

Thomas Greenhill 3/32

[@joedunnaway4728]

16th inch Balsa... There are 4 more videos prior to this one showing sheeting and foam core preparation.

[@x.a.m1960]

I'am no balast you balast?

[@spammerscammer]

I wouldn't buy into the carbin fiber info you heard. Carbon fiber gets its strength from multiple cross hatched layers held together with epoxy. Better off using just Monikote or typical laminating film.

[@pratimatripathy6611]

can man fly with these wings?

[@yasmanimartinez4117]

Hello! Can you help me to send a plan over what I need. Or were on the Internet I can download? ? ? ? ? ? ? ? ? ? ? ? ?

[@mohamednacir7989]

+Moh e amed Nacir

[@Ra_dio_Iberico_ea4ggc]

Un Cuarto de HORA de Vídeo = 15 minutos, para ver como enchapa, un Corte de Ala de/en FOAM.