Shell Thickness Calculation under External Pressure in Pressure Vessels

[@jaysuryawanshi2089]

The videos you post are helping many people like me to gain deeper insight in this field. Thank you.

[@fnengineering]

Thank you for watching and visiting FN Engineering channel

[@shreyashmehta839]

Very well explained. Thank you very much. Plz upload the next video.

[@fnengineering]

You're welcome. Thanks for visiting and watching FN Engineering channel. I hope, I can updated the next video

[@TheHaimoud]

ALLAH BLESS YOU AMAZING CHANNEL

[@sojibbd6180]

Best of Luck

[@bhaveshparmar9727]

The video was very good & helpful. Please improve the quality of the voice. Thank you.

[@elhamsadeghinia]

Thank you very much

[@abhisheklad6892]

Very nice 👍. I would request you to please make video on U-Tube thickness calculation for external pressure. This should have two case i.e. with differential pressure and without differential pressure. Thanks in Advance 👍

[@fnengineering]

Thank you for watching FN Engineering channel. Your suggestion is great. We will consider it. Regards, FN Engineering

[@orlandoemanoel2409]

Please, and if my temperature is low? About 2 °C at deep sea?

[@bekirtuncay]

Hello, how do we calculate the shear stresses and von mises values on the outer surface?

[@manivannanharikrishnan5752]

Thank you please make video for jacketed vessel

[@fnengineering]

Thank you for watching and visiting FN Engineering channel . We will consider your suggestion

[@palomar439]

I have a question. What would be the relationship or equation relating External Pressure measured in MPa and Internal Pressure measured as in mbars. For example 1,5 MPa of External Pressure what would it be in mbars of Internal Pressure ?

[@JR-ze5ss]

It's quite helpful. I was wondering if you would explain how to calculate shell thickness with stiffening rings.

[@fnengineering]

Thank you for watching and visiting FN Engineering channel . We will consider your suggestion

[@carlosmolinagodoy1115]

thanks for the video. i have 1 question: in my case i have a vessel that contain air and water internally (is a priming tank), i know that the water temperature is 50 celsius, but i don´t know the air temperatura. in this case what should i use like design temperature?

[@fnengineering]

For design temperature you have to choose the larger value. You can estimate working temperature of air such as 60 deg C. So, you can determine design temperature 80 deg C

[@imranzada937]

hello there, why don't we consider the allowable stress value for a vessel under external pressure?

[@sacheewg1997]

Thank you very much for the video

[@fnengineering]

Thanks for visiting FN Engineering channel

[@mdirshadali8817]

Where is the second part?

[@fnengineering]

Until now, there is second part for this material

[@imranzada937]

it was really helpful and I did my project because of your video. BTW I couldn't find your excel sheet related to this video. where I can find it?

[@fnengineering]

thank you for watching and visiting FN Engineering channel. Here is the link for external pressure calculation bit.ly/FNEngCalc4

[@gopunair973]

@@fnengineering but it asks for password

[@titusvanadio2317]

@@fnengineering need password, can I?

[@syedzainabbas895]

Well explained. When will the next part be uploaded?

[@fnengineering]

Thanks for watching and visiting FN Engineering channel. We hope we can make the next video in this month

[@vikasmishra1774]

Please make a video on head thk. Calculation under external pressure

[@fnengineering]

Thank you for watching and visiting FN Engineering channel . We will consider your suggestion

[@MrAndrew778899]

Bro in the Fig. HA-1,what is E and its unit?

[@fnengineering]

E is modulus of elasticity in MPa or ksi unit

[@carlosmolinagodoy1115]

is the 1.5 MPa (study case) a manometric pressure?

[@fnengineering]

1.5 MPa is gauge pressure

[@pettersoncorreia5535]

will you send the spreadsheet?

[@anengineer8647]

Hi sir why did you remove /private videos from pressure vessel series??

[@fnengineering]

Some video have been published again. Please check again

[@vikasmishra1774]

Sir why did you remove some video from playlist

[@fnengineering]

Some video have been published again. Please check again

[@bxushagshx]

Hi ..why some video are private?

[@fnengineering]

Some videos have been published again. Please check again

[@eljaygardose8274]

Sir spreadsheet is password protected,can i have this?

[@fnengineering]

Hello Eljay, the password is "FN Engineering"

[@eljaygardose8274]

@@fnengineering thank you sir

[@suksesselalu2893]

Mau tanya kak, kenapa di factor A itu jika diasumsikan t=10mm dapetnya 0.001800, sedangkan t=8mm dapet 0.001300?

[@fnengineering]

Itu didapatkan dari chart. Nilainya mungkin berbeda dari beberapa orang yang menggunakan karena pembacaan dari chartnya

[@solosinger6679]

Spreadlsheet link is not working , pls update

[@fnengineering]

The link should be worked. Please check again

[@ewssalt9421]

I cannot get either. The link for Spreadsht1 and Spreadsht2 are not tally with the video explanation...

[@anmolmodi877]

I am unable to open your spreadsheet, it says incorrect password

[@fnengineering]

Hello Anmol, the password is "FN Engineering"

[@sajeeth3504]

Reinforcement excel file is not opening, can you pls upload in excel format

[@fnengineering]

You can see in the spreadsheet, the link has been written in the description

[@mdirshadali8817]

Where is the second part of the video?

[@fnengineering]

Until now, this video just has one part

[@petersalomons3234]

Could I get your email- as I have a unique situation on a vacuum vessel to discuss

[@fnengineering]

Yes of course, here is my email [e-mail]