Shimming the engine block of B5254T4 for Volvo S60R/V70R

  Рет қаралды 35,968

SwedeSource

SwedeSource

Күн бұрын

In this video I do a quick teardown of an S60R B5254T4 engine and then give brief instruction on how to shim the small gap between the cylinders on any Volvo whiteblock engine.

Пікірлер: 85
@untitleditem2334
@untitleditem2334 6 ай бұрын
hahha, nice mark you left on the cylinder sleeve at 4:50. Then went on to say how you don't want that. That must have hurt.
@ehmjauhh5495
@ehmjauhh5495 5 ай бұрын
He didn't even see it I beleave 😂
@swedesource6785
@swedesource6785 21 күн бұрын
@@ehmjauhh5495 Sadly, I did see it.. I hate myself for it 🤣 but thankfully it's an inconsequential area.
@jmccarsnmore1025
@jmccarsnmore1025 2 жыл бұрын
I’m looking at a V70R, and heard the phrase “shimmed block” because of a known issue. And the fact that I now know what it means, and can see the cylinders divided in between, it all gone through the toilet!! No way I’m getting this car!! 🤣 🤣 🤣 Next car I get, closed deck all the way!!
@swedishtuners6518
@swedishtuners6518 2 жыл бұрын
U will still get gapped by one 💀
@TCBOT
@TCBOT 2 ай бұрын
what ya end up gettig
@Itz_Joe_Here
@Itz_Joe_Here Ай бұрын
Can you make the shims shorter or less in width to fit better?
@belekas2729
@belekas2729 3 жыл бұрын
4:50 Engine block was damaged little bit after tapping.
@swedesource6785
@swedesource6785 3 жыл бұрын
Yes, I did tap that outer edge a bit. I was looking at the camera and not what I was doing. Fortunately, it's an inconsequential spot because it doesn't aide in the sealing of the cylinder to the head. Obviously it was frustrating but I didn't notice it until after I had made the video 🤷‍♂️🤣
@belekas2729
@belekas2729 3 жыл бұрын
@@swedesource6785 Glad it's ok. :)
@MrCrabbing
@MrCrabbing 3 жыл бұрын
@@swedesource6785 I reckon it was the ball bearing that caught it there, I have a B5234T4 and I have just started to see coolant in my oil, only a little hardly anything missing from the expansion tank at all but the oil has discoloured on the dipstick a little, once I started it from cold a couple of months ago and it had a slight misfire, it went after 30 seconds or so and has not done it since, I'm hoping its not the liner issue I didn't think this was common on the 2.3 engine?
@austenbarton2027
@austenbarton2027 3 жыл бұрын
@@MrCrabbing B5254T4 engine is a 2.5. Hence B5(25)4T4
@MrCrabbing
@MrCrabbing 3 жыл бұрын
@@austenbarton2027 B5234T4 R5 2.3L
@austenbarton2027
@austenbarton2027 3 жыл бұрын
Does the shims being so long, extending that far into the coolant passages, partly blocking them right off, restrict coolant flow in any way?
@johnthompson5466
@johnthompson5466 2 ай бұрын
it's got 2 I'd try to bend them a little more at the end so that they flow better but that might cause a problem for whatever reason
@jockobacumbo623
@jockobacumbo623 Ай бұрын
Why do you have the extra length on the ends protruding into the water passage? Could you give the measurement of the length of the shim and not just the thickness? How did you fabricate the metal for the shim and what is it made out of?
@lukaszperski9370
@lukaszperski9370 Жыл бұрын
I think the shims are too long and it can affect on cooling, why didn't you cut them to have 2-4mm for each side?
@ryanspeck2248
@ryanspeck2248 3 жыл бұрын
A steel shim in an aluminum block? Wouldn't the different thermal expansion rates cause issues?
@nikolai502
@nikolai502 3 жыл бұрын
I would believe the space between the cylinders was Split for a reason
@TommyboyGTP
@TommyboyGTP 3 жыл бұрын
Vast majority of aluminum block engines have steel sleeve cylinder liners. You can see it in the video.
@magnus122
@magnus122 2 жыл бұрын
How common are these cylinders to crack? I really want to get my hands on a ‘05 S60R within the next 2-3 years, and just want to know what to be cautios about when it comes to maintenance and stuff like that? Let’s say I go for a stage 1 tune pushing 354hp / 493 nm torque. Will I have to worry about shimming the block?
@airmalone2813
@airmalone2813 2 жыл бұрын
Prob some people have cracked them on stock tune
@Sr.-Mizz
@Sr.-Mizz 2 жыл бұрын
About 3 in 10. Alot of Europeans swaped to the regular 2.5t engine and tune it since the cylinder walls don't have that gap. But it's all dependent on how many times and how often the owner pushes the car.
@wiktorhogberg1952
@wiktorhogberg1952 Жыл бұрын
@@Sr.-Mizz Every whiteblock engine has the slot between the liners. Making them hold a lot of power is all about tune.
@BuiltForSpeed
@BuiltForSpeed 4 жыл бұрын
Maybe make the shims to sell for who wants to do it?
@BuiltForSpeed
@BuiltForSpeed 4 жыл бұрын
@@k89ranger i dont think there is a .031 size.
@swedesource6785
@swedesource6785 4 жыл бұрын
@@BuiltForSpeed I purchased a large roll of 0.031" steel. I have enough to probably make 200 shims.
@DMDAUTOLLC
@DMDAUTOLLC 4 жыл бұрын
Yes make some and sell them cheap I need another Swedesource sticker for other side of wideshield
@swedesource6785
@swedesource6785 3 жыл бұрын
@@lumimobb I'm also working on making shims for sale. I've got enough material to make about 300 shims.
@syahizad
@syahizad 3 жыл бұрын
Good info.. Thanks.
@willriley1619
@willriley1619 3 жыл бұрын
It just taps in that easy? No cutting or anything like that?
@TommyboyGTP
@TommyboyGTP 3 жыл бұрын
Can you shim the block with it still in the car?
@dirtypeach
@dirtypeach 3 жыл бұрын
This is a good question
@brandonlittle6444
@brandonlittle6444 2 жыл бұрын
@@dirtypeach Yes
@oldgary1855
@oldgary1855 3 жыл бұрын
this is kind of like asmr
@HandMadeWrath
@HandMadeWrath 3 жыл бұрын
Whats asmr?
@alouisschafer7212
@alouisschafer7212 Жыл бұрын
Is this an issue with the NA engines at all? The T4 makes around 300hp while the NA versions are below 200hp. While they all use the same block right? Well, no surprise the open deck block with expansion gaps in between the cylinders has its limits.
@DarthVader-gc2os
@DarthVader-gc2os 3 жыл бұрын
How do you know that the shims will stay in place and not slide down over time?
@SawDawify
@SawDawify 3 жыл бұрын
The slit is only at the top of the cylinder it doesn't go any deeper
@swedesource6785
@swedesource6785 21 күн бұрын
The slot is only nearly as deep as the shim is wide.
@mrnurse4479
@mrnurse4479 2 жыл бұрын
Nice video, whats the purpose and bad side of shimming the engine block?
@Sr.-Mizz
@Sr.-Mizz 2 жыл бұрын
If those gaps are not shimmed, the cylinder walls will crack, causing catastrophic engine damage. Regardless if the car is tuned or bone stock
@SVTKeats
@SVTKeats Жыл бұрын
Do you need to pull the engine to do this or can it be done in car? Early stages looking at a T5 V70R and a S60R. Not sure which way I’ll go
@swedesource6785
@swedesource6785 Жыл бұрын
You can do it with the engine in the vehicle no problem.
@clonetrooper576
@clonetrooper576 4 жыл бұрын
if i did go buy the sheet metal shims, i know their thickness but about how long would these be? and do they need to go lower into the block or is what you have sufficient enough?
@swedesource6785
@swedesource6785 3 жыл бұрын
The shims do not need to go lower, the problem area is at the top of the cylinder. You can save a lot of time by purchasing our shims.
@maimaira6756
@maimaira6756 6 ай бұрын
​@@swedesource6785 do you have for volvo s40 t3 engine
@phiberoptick
@phiberoptick 3 жыл бұрын
0.031 inch = 0.7874 millimeter
@vladimirmazurin4539
@vladimirmazurin4539 2 жыл бұрын
Здравствуйте подскажите пожалуйста эти проставки нужно ставить на двигатель volvo s60 2.4 т В5244т3 и сколько они стоят
@dennisbreeveld6842
@dennisbreeveld6842 21 күн бұрын
Will the shims not slide down over time?
@swedesource6785
@swedesource6785 21 күн бұрын
The slot doesn't go deeper than just about the width of the shim.
@k89ranger
@k89ranger 4 жыл бұрын
Can't wait to shim my block so i can add water/meth and crank the boost a bit more.
@dafretz
@dafretz 3 жыл бұрын
@Gustavo Braylon SPAM
@dafretz
@dafretz 3 жыл бұрын
@Valentino Tanner SPAM
@jamesgeorge6551
@jamesgeorge6551 3 жыл бұрын
B5234T3 Owner no silly shim business, thank you. But the H/G is toast :-(
@MisterTurnister
@MisterTurnister 3 жыл бұрын
2.3L no shimming needed? up to what HP? And what does "H/G is toast" mean? Thanks!
@marshkid1
@marshkid1 3 жыл бұрын
How long does this take to do? And what are the costs? How much would you charge? Thanks!
@swedesource6785
@swedesource6785 3 жыл бұрын
Message me directly through the SwedeSource Facebook or IG account.
@HandMadeWrath
@HandMadeWrath 3 жыл бұрын
My machinist didnt charge me for this since he didnt have to machine anything.
@johno9507
@johno9507 2 жыл бұрын
I'm trying to understand a statement you made on another comment. Did you shim the engine after the cylinder cracked, and then got another 100000k miles out of it? Ie: Will shims fix an already cracked cylinder?
@swedesource6785
@swedesource6785 2 жыл бұрын
I've never done that, no. But I've heard of people successfully doing that. Obviously, I'm sure it highly depends on how bad the crack is. Basically, I've seen people stuff JB weld into the slot with a shim and just call it a day. Sounds like too much work for a "maybe".
@johno9507
@johno9507 2 жыл бұрын
@@swedesource6785 Thanks for the reply. 🙂🇦🇺
@stebansb
@stebansb 3 жыл бұрын
What Is the shims function on an engine?
@AADiego
@AADiego Ай бұрын
reinforce the cylinder walls so they dont crack under pressure
@Pri78G
@Pri78G Ай бұрын
Nice video but while shimming can strengthen the engine structure, it could have unintended consequences such as hindering coolant flow or restricting cylinder sleeve expansion. cylinder sleeve gap is there for a reason. These engines have been designed by engineers with qualifications and years of experience. Is there concrete statistical evidence to prove that shims actually fix the problem? What if multiple variables are contributing to the problem? Poor tuning, poorly maintained cooling system. Excessive revving, poorly maintained lubrication system...etc.
@JMT1227
@JMT1227 Ай бұрын
If there were actually unintended consequences, people would be talking about it. But they aren't. If the engineers knew what they were doing, cylinders wouldn't be cracking in the first place. The best motors out there are completely closed deck. Honda guys fill their blocks. I've personally been selling shims for years, and not a single person has came back saying their motor cracked.
@Pri78G
@Pri78G Ай бұрын
@@JMT1227 Thanks for taking time to respond. I had to be honest and open with my question because I drive a stage 2 tuned 2010 Focus ST. It doesn't have shims however, I don't do track driving. Still a concern though.
@piotrhazymut1953
@piotrhazymut1953 3 жыл бұрын
How much engine will take after this operation? Can I buy this shims from you?
@swedesource6785
@swedesource6785 3 жыл бұрын
Yes we sell the shims on our website. There isn't really an answer about what it can handle. That highly depends on your tune, fueling, and many other factors. I'd say it's safe to say that it can at least handle stock horsepower 🤣 I personally ran 20 PSI reliably on the stock internals with shims.
@williamgolden839
@williamgolden839 3 жыл бұрын
Can I ask what this fixes or improves?
@swedesource6785
@swedesource6785 3 жыл бұрын
The small gaps between the cylinders allows for the cylinder walls to expand, and when that happens they crack. The middle two cylinders are particularly prone to expanding and cracking. This problem is primarily on the B5254T4 engine out of the S60R/V70R because it has the thinnest cylinder liners out of the 5 cylinder engines installed in Volvos. Thin cylinder liners, combined with the highest horsepower and torque output of any factory 5 cylinder means bad news. Shimming the gap with snug pieces prevents the expansion of the cylinder liner. So far, I personally haven't heard of anyone with a shimmed block getting a crack in their cylinder liner. It's not a perfect solution, but it's the most cost-effective one. I personally owned an S60R which ended up having two engines with cracked liners, and since shimming I continued for another 100k miles without another cracking issue.
@williamgolden839
@williamgolden839 3 жыл бұрын
@@swedesource6785 thanks for the answer
@RepsolRC211V
@RepsolRC211V 2 жыл бұрын
@@swedesource6785 does that shims prevent cracked liners? thas is problem on fosus rs mk2 305hp with B5254T3 engine too? it is posible to re-sleeved it?
@johno9507
@johno9507 2 жыл бұрын
@@swedesource6785 I'm trying to understand your statement. Did you shim the engine after the cylinder cracked, and then got another 100000k miles out of it?
@mrscootscoot662
@mrscootscoot662 Жыл бұрын
@@RepsolRC211V The shims help prevent the cylinders from expanding which is what causes them to crack, so yes this will help prevent the similar issues with the cylinder liners. Ford owned Volvo in the mid 00's and the Mk2 Focus RS used a variant of this engine so it's highly likely this would be a solve there too.
@duhduhlovo1670
@duhduhlovo1670 3 жыл бұрын
What did you use to clean the cylinders
@swedesource6785
@swedesource6785 3 жыл бұрын
Scotch pads and elbow grease. Tape off the deck and you can also use a wire brush for heavy buildup, just bring the piston to TDC while doing this.
@jogin211
@jogin211 Жыл бұрын
Oh fukc in 4:49 you tipy tap tap that shim and hit cylinder top with ¼ socket. You destroy it...
@justintosch7162
@justintosch7162 Жыл бұрын
Yes, but that's not where the gasket seals. It's a non-crucial area. It won't have any effect on the engine.
@jim5alive
@jim5alive Жыл бұрын
Dude marked the head gasket mating surface. Not cool.
@JMTosch
@JMTosch Жыл бұрын
Fully aware. I was watching the camera and slipped up. Thankfully it was an inconsequential location.
@forwhatitsworth364
@forwhatitsworth364 3 жыл бұрын
Just put some sway bars.
@CaptainBreny
@CaptainBreny 2 жыл бұрын
0.78 mm :D
Why Inline 5 Cylinder Engines are an Anomaly
17:55
speedkar99
Рет қаралды 536 М.
V70r Build: Head Work & Installation With New Head Gasket
19:29
eurojulien
Рет қаралды 12 М.
What will he say ? 😱 #smarthome #cleaning #homecleaning #gadgets
01:00
Oh No! My Doll Fell In The Dirt🤧💩
00:17
ToolTastic
Рет қаралды 13 МЛН
Electric Flying Bird with Hanging Wire Automatic for Ceiling Parrot
00:15
Cute kitty gadgets 💛
00:24
TheSoul Music Family
Рет қаралды 21 МЛН
Elevate Performance Engine Sleeves Demo Block Sleeve Type Comparison
6:12
ELEVATE Volvo Performance
Рет қаралды 33 М.
Volvo S60R/V70R 2.5l Engine rebuild/ shimming and assembly detailed DIY.
19:08
Things I love and dislike about my Volvo S60R
9:50
Josiah Rothe
Рет қаралды 53 М.
Here's The Reason Why I Will Always Own A Volvo
13:48
Shifting Lanes
Рет қаралды 188 М.
Manual Volvo V70R: 5-Cylinder Forever Car // CARISMA
8:19
The Drive
Рет қаралды 56 М.
DEAD AT JUST 100K! 2015 Volvo XC60 T5 2.0L Engine Bites The Dust
38:32
Volvo B5254T - Block reinforcement to 800hp +
4:30
Veicomer Engine Performance Solution
Рет қаралды 197 М.
What will he say ? 😱 #smarthome #cleaning #homecleaning #gadgets
01:00