DIY Boat Dashboard Upgrade On Our Old Boat Part 2.

[@ShipHappensAdventures]

Our Veratron VMH70 Digital dash - veratron.com/products/vmh-70 Check out Hudson Marine and use the code Shiphappens5 for 5% off all your purchases hudsonmarine.co.uk/

[@MikeAndCarolineKolling]

so two grand then?

[@chonzie16]

Looks great 👍

[@2thehook773]

Well done! You should seriously consider putting some analog gauges on the engines as a backup. Even in aircraft, a glass cockpit has essential gauges as backup. Love your channel.

[@meofnz2320]

As a counterpoint to those suggesting keeping analogue gauges on the engines as a back up… Why? You don’t really need gauges at all in a get you home situation. You still have separate sensors and alarms for oil pressure and temperature. And you don’t usually have backups for analogue gauges, which aren’t immune to failure.

[@buffplums]

I do like digital but the only thing that would worry about is if there was an electronic failure say power supply, then you lose the lot. As an electronics engineer, I have always found that simple is often best with analogue gauges, you have so much more robustness and reliability … highly integrated electronics are so much more vulnerable to voltage transients and static. From my own experience, I have seen something as simple as a voltage regulator that overheats and fails, Next you have 24v down a 12V supply rail and any microprocessors, ram etc usually die, especially now as most processors run on 3v3 and you have multiple regulators stepping down from say 24v … that’s a big power drop so we use switching regulators which are much more efficient but even so, I, always am a bit wary about digital. As a compromise, what you could still do is keep all your old instruments and make maybe just an essential analogue panel but wire an extension cable to a multi pin connector and have a hidden breakout connect under the main dash and keep your analogue panel on board stored somewhere and if the worst happens you can hook up your old instruments again. Would hate to think of you being stuck out at sea and without any means of seeing your data. Anyway, just my thoughts, I do love what you have done but just my honest thoughts as an electronics engineer of some 40 plus years lol 😂

[@andyb9127]

Interesting point but were the gauges being replaced truly analogue? During the dismantling of these gauges, it's clear they are being controlled by an electrical wire, not a mechanical cable. Therefore the pre-existing system was also electricity dependant and wouldn't an electrical fault also had caused the loss of readouts on the old gauges? Honest question, I really don't know the answer.

[@38whitcomb]

I am in the marine repair business and a ABYC technician in Massachusetts. I am impressed with all of the projects you have taken on it's awesome Job. I look forward to each episode. Keep up the great work

[@keithstandiford3761]

Really Pretty! But as an aircraft guy, I'd mount a couple of oil pressure gauges right on the engines in case of electrical failure.

[@AndrewJackson-mf5qp]

The new dash looks awesome guys. I would be inclined to still use the analog for redundancy for engine monitoring. Im old and electronics are not reliable enough for me.

[@Vara169]

Oil pressure coolant temperature and depth are critical, and there should be fail safe systems for those. Engine shutdown, and warning for depth. Have experienced all 3 in my 40ft launch, each one saved me.

[@davidswain5687]

Brilliant dashboard but I have to agree, I think you'd do well to have a couple of analogue guages as backups to your amazing digital setup. Great video, keep them coming, please. Cheers Dave Swain and family xx😊

[@JohnGalvin-o9t]

Hi Guy's. What would look nice would be to have some decretive rope work whipping TDC on your wheel. It would also give you a visual reference point if the sun's obscuring your screens...

[@jamesa7506]

It does look fancy and well done on the workmanship but you should consider having a few mechanical gages on the engines also. An additional, and comparatively inexpensive, level of insurance.

[@johnwynne2179]

Brilliant job, dash looks clean and modern, would of kept analogue as a back up, but that's just my personal opinion.

[@markclifton14]

The dash board looks great now. Such an improvement . Makes the boat look more modern. 👍👍👍👍👍👍

[@donsaxon7723]

What a transformation. The new digital dash board looks fantastic. Enjoy watching your channels. Keep up the good work.

[@BeeSting862]

If you are wise, when you install a video camera in your engine room, use one with infra-red capability. A quick scan of the screen can tell you if any component is overheating.

[@DuncanBeaird]

I agree with 2thehook 773 1000%. Since you have the analog gauges now redundant, make them redundant, in the engine compartment. You should have some nice pieces of left over aluminum sheet you can even use. Or, just use pieces of the chunks you cut out of the old IP. Good work, though, it looks great!!!

[@hamshackleton]

Quick safety question - as you have changed all the metalwork around it - have you 'swung' your magnetic compass to see if it still reads something like correct - just in case all the electrics quit, and you have to navigate home the old-fashioned way?

[@patriciacrumrine5890]

Awesome, pretty, sleek, elegant, functional, wonderful improvement to your "investment" boat. So cool to see Boutari skimming the waters, knowing how you've made her more safe and powerful. Happy sailing.

[@shelleyregnier6671]

That dash looks splendid! So clean and zen. Whoever purchases that boat from you guys (eventually, when you are ready to part with it) will be very fortunate as you have done such a nice job on bringing it up to spec. A Gemma & Simon job is a quality job, every time!

[@maxiemills6982]

After a rough start this boat has turned into a beast!

[@fxpthl]

You are a very talented couple who know just what to do when upgrading your boat!

[@Omri_Makes]

New digital displays look great, well done. cheers

[@marksmith-ew7ir]

I like the new look brings the instruments up to parr,saves the units from light fingered people.would an analog gauge on the engine compartment to see when working on engines if you can't see the screens.

[@mariastaples638]

He is like a little kid at Christmas 🎄🎁 awesome job again S and J we'll be watching for the new thank you for sharing your talent with us John and Marie

[@Sluf7]

Nice job Team looks great. 😅 Now ya can set Alarms for everything. 😮 I will go partial digital as the Analogue gauges on my Twin outboard 24 footer just look to good. You really had to do Digital thing for resale later....😮 Mind you Boutari could be tender for Sarinda...😂😅 Yup just enjoy her now once Gem gives her a once over cleaning wise 😮😂. Carry on now😅.

[@johankotze42]

Great job! :-) I picked up somewhere else that those screens (chartplotter etc) so close to the magnetic compas, will throw it out. Just look into that.

[@goleafsgo8496]

"Crackin" upgrade I would say. Today's electronics are so cool compared to the ole days. Great call on the Carbon Fibre wrap material and for sure the lower portion really brought it all together. 😊 enjoy the boating season with the family ....

[@shogun666able]

Nice set up if you believe digital over analogical in damp / wet conditions is the way to go, but pretty brilliant what can be done. Years ago in Nav classes and sea training the first thing your told when not just coast hopping is never depend on anything off of a battery. Things move on where instrumentation is concerned, but will they really stand the test of time for what they cost, in the condition their in such as a open boat. However Simon very clean, tidy set up being all handmade..

[@johnm8939]

New dash came out awesome! Great job, enjoy your videos.

[@ShipHappensAdventures]

Thanks 👍

[@barrywood5357]

Well done when you getting your own boat yard........ now there's a thought..... nice one crack on

[@themarinerkommer4371]

it would be really good if the screen for the readings of rpm oil etc was bigger like the ray marine then i think perfect but they seem to have small icons on the display with a larger screen you can put more things being monitored and see them better from a distance cause they will be bigger. the analogue was good i.e. the tachos but size wise as they were easy to have a look at.

[@everestyeti]

Brilliant upgrade, would definitely add a camera to the engine bay plus a camera on the bow it would be another set of eyes when your moving at speed. 👍

[@raycarlson1342]

Excellent job it looks really professional. Just one thing I would be concerned about. Is that a magnetic compass mounted on top of the dashboard? if so you could get some unwanted magnetic effect from the instrument electrics. I bet you have already thought of that though 🙂 RayC

[@andrewjones-productions]

I love what you have done to the boat. Both in terms of repairs and upgrades. However, I love even more that you have made boating something that anyone can do and that it is not only a playground for the rich and famous. Of course, those that are familiar with boating already know that, but for many of us, this false perception of it being something beyond our reach or capabilities, the message that you are sending out is just fantastic.

[@looyosummers5796]

Love the new dashboard, it's less reflective when you're out on the water, easier to see at night if needed, plus it looks gorgeous.🥂

[@peterrobierto7435]

Nice installation, with redundancy as well. Perhaps some spare part sensors would be nice to have but probably a bit pricey 🤙

[@killeresk]

Looking good now and matching too.. Nice.

[@ShipHappensAdventures]

Thanks 👍

[@rolandtb3]

Time to enjoy boat life after all the ups and downs. Dash looks great. Any glare to affect screen visibility? Still have opportunities to add more layers as you proof the various settings.

[@rongreen4766]

Looks good. Does this mean Sarinda is also getting an instrument upgrade ? Also I agree with previous comments regarding analogue backups. Love your videos. Keep up the good work.

[@Rogster559]

Now it’s done even though you know it’s eventually going to be sold it’s going to be very hard to part with such a beautiful boat , it’d be ideal down here in Tassie out chasing 100 plus kilo tuna , swordfish , marlin or just cruising around the island or slipping over to the mainland love all of your vlogs best wishes from Tasmania Australia 🇦🇺

[@DirkvanZyst]

Well you two have certainly knocked it out of the park as the Americans say. Beautiful job in the finishing and fitting, good choice of the carbon fibre covering. Very jealous I am. I'd love that boat, those engines sound magnificent. I can't remember if they are direct drive or stern drives, they look like inboard direct drives from tat gorgeous wake. Well done and have a fantastic summer cruising. 😎🥰

[@scottjones5221]

Beautiful ❤ job well done

[@Drew67072]

As I am suffering with poor eyesight those digital screens really pop out at me and defo a big plus for navigation and local charts etc. good job guys as usual😊

[@ShipHappensAdventures]

We love the digital dash, analogue gauges are only good if your looking at them, with digital you can set the alarms to the parameters you want so never the chance of something overheating

[@ToddTalksTech]

Fantastic job on the dash, as an electronic wonk the backside of the 80's dash looked daunting. Congrats on an amazing job!

[@alexugljesic]

Beautiful conversion! Well done!

[@WayneCoke]

Looks great guys, you did well covering it and then the cut outs for everything was spot on. Now all you need to do is catch some real eating size fish. :)

[@seankearney2592]

Well Done to You Both,You Done an Extremely Excellent Job On Your Dashboard,Hope you Have Many a Pleasurable Day On The Boat.

[@ShipHappensAdventures]

Thanks 👍

[@eddyhammerton3310]

you have made a great job of the dash looks very sleek and professional

[@ivorbexon4030]

It looks brilliant, ideal for what you want. You can always add some more to the collection.

[@simonmercer9530]

Looks really good. I love carbon effect nice work guys

[@ShipHappensAdventures]

Thanks! 👍

[@berndm9743]

What a cool set of displays. Congrats on a great installation and setup.!!!!

[@CaptWho]

It looks beautiful, but you probably should upgrade that switch panel in the headliner (and any other switch panels) above your heads to match.

[@jaygee5693]

The overhead switch panel doesn't match, true, but it does look good and the white is a nice contrast with the new black dash.

[@denis9450]

Outstanding guys as usual your workmanship is second to none

[@poddy1957]

That looks fantastic .. Really nice job .... One for SV Seeker, Doug Jackson "What did you make today" 👍

[@denniswray470]

You two have done a brilliant job of that dashboard it looks wonderful.

[@urbanfox53]

Hi guy's lovely looking dash upgrade, but have you thought about ventilation, the dash is black and will be exposed to Sun and will generate a lot of heat? I would put vents in the sides

[@GoofieNewfie69]

Now you need an engine synchronizer , push a button and both engines run at the same RPM. Then a remote control so you can drive from anywhere on or off the boat

[@ronkluwe4875]

Two thumbs up and a real transformation of the dash. Glad to see you got some time for relaxation, even if it was for a test run of the new dash set up. Is your plan to use the same type of dash instrumentation for the big boat?

[@BarrieHarmsworth]

What's wrong with whiting? Tossed in a frypan with butter they are delicious.

[@jaygee5693]

I agree, they are good eating, and I like them crumbed, fried in butter, or foil wrapped and baked. I think that some people consider them "common" because they're so numerous and sometimes all you can catch. The flesh is flaky, so unless they are very freshly caught it can be tricky to cut whole fillets, but then they are beautiful in fish cakes.

[@stevenborman9110]

needs a mobile phone holder :) plus looks damn amazing And, and, when is the Ship Happens cooking channel coming,all those fish, musy have some recipes. Just more work for Gemma to edit, but she''l be fine :)

[@joncarter3817]

You guys are just so great. Always enjoy the main channel but this channel covers issues and upgrades normal boaters deal with. Don't know how you keep both channels together but keep it up for sure!

[@chilllytube]

I know you are excited by this but it's much more interesting watching you build or repair stuff. Programming someone else's bit of kit is not a great watch. I hope you have a backup for that day the single point of failure fails. Look forward to the next building stuff video.

[@rolanddunk5054]

Hi,WOW what a cracking job it looks beautiful and very professional.cheers Roly🇬🇧.

[@ShipHappensAdventures]

Many thanks

[@billmeldrum2509]

Fantastic transformation. You guys rule. 🇨🇦

[@keithweybury5212]

Looks awesome guys. Great job.

[@ShipHappensAdventures]

Thanks so much!

[@ebutuoyotwen]

I sense a water viewing of Sarinda coming soon. Seems like the ladies should meet :)

[@BenjaminTaylor-ho6uy]

A little late catching this video, but, as I have said befor ( another work of excellence out the door! Congratulations!

[@daverichardson5861]

You’ve done a super job there guys, looks mint and so up to date. However, the steering wheel needs to be quick release like on F1 cars. Lol. Stay well you two.

[@harrisonandrew]

It looks so high tech and swishy. Great work guys. Very entertaining.

[@ShipHappensAdventures]

Thanks so much!

[@michelrood2966]

I like how you say " we" when in actuality its Simon doing it 😊

[@Bob8091]

Can you come round mine. The hallway light switch doesn't work.

[@ShipHappensAdventures]

You sure it’s the switch and not the bulb?

[@Bob8091]

It's the switch. I had a sparks fix it but he didn't guarantee it has he needed to use an old one from his van.😢

[@bigalon3wheels]

Nicely done guys, like your choices for the new dash on the power boat

[@jiminauburn5073]

That console looks fantastic.

[@nickhayes9222]

Any word on differently pitched props for her? I believe there was some discussion at one point about the props you installed being a limiting factor in top speed.

[@hughmason1950]

Agree with what most the comments made so far, looks great but would still think of a way to make an emergency analog board to use in a total power failure.

[@assassinlexx1993]

I wonder is there a seal between the new screens and the dashboard? So no water ( spilled tea) can get into the back of the screens. Other suggestion is a independent bilge switch to a alarm. So if the main bilge system fails ( they often do) you still have a alarm that you have problems below😮 Cheers

[@ShipHappensAdventures]

We have a flood alarm in the bilge, and the screens are sealed, but everyone is on strict orders not to put a cup on the new dash!!

[@rickdommett]

you both are amazing, I enjoy all your videos............I'm from Canada, cheers.

[@ShipHappensAdventures]

Thanks so much!

[@dannieport9254]

Is Canada the only place that uses the far superior Robortson screws? First thing I do when I get something is replace the slot and Phillip's screws.

[@arkansasboy45]

That turned out way better than I thought it was going to. Great job!

[@ShipHappensAdventures]

Thank you! Cheers!

[@kroneditor9266]

Fantastic upgrades and love the carbon fibre look - Great work again!

[@ShipHappensAdventures]

Thank you very much!

[@richardgould240]

Looks great, like you said it’s time to use it.

[@jannerkev]

Nice job. Good looking bit of kit. But do you have analog gages in the engine room as a secondary spare?

[@akilby8022]

What a great upgrade 👍 super job guys 👍 My dashboard definitely needs upgrading but I’m a bit unsure how to proceed 🤔

[@martinhajee3488]

Looks really good, well done, to both of you. Quick question, have you managed to fix your auto pilot ?

[@joemackenna4980]

Nice job on the dashboard. been following your channels for a while. However did you give any consideration to putting expensive electronic in a black enclosure. My experience is that black on a boat generates a lot of heat. I mean a lot. Are you worried you might cook for electronics?

[@buffplums]

Looks really great guys the wraps on the 2 panels really bring the whole project together. Well done. By the way, why do you have 2 levers per engine throttle? 😊

[@vincentcarrano6329]

Awesome upgrade guys

[@malcolmadams1051]

On your new instrument panel can you digitally label your Guages?

[@johnbrightman282]

SOLAR PANELS TO CHARGE BATTERIES +INVERTER TO MANINS POWER NEEDS.

[@heatherrawls6015]

Very cool! great job Simon and Gemma

[@davebrown7321]

hey guys great job on the dash & do you eat whiting over there cause they're big good tucker here in Australia!👍🍕

[@4437RR]

I may have missed it in the narrative but did you verify/ adjust actual temp/pres values to readouts?

[@drj5758]

Way more slick set up and programmable! Star link?

[@Fleetsuper]

That is one sharp console, well done

[@martyndeyoung8207]

Neat installation! Are you planning on something similar for Sarinda?

[@MakingWaves-IsleOfMan]

A great job done with the dashboard and with the boat overall, Hell yeah! to taking it out on the water, any plans to come over for the TT again this year?

[@radicalradiotech4944]

Thats a brilliant setup guys congratulations!!

[@ianmcfadden4709]

nice job on the dash looks super

[@Audit-The-Auditors-UK]

With the cameras add night vision to engine room, stern and the bow.

[@stephenshort839]

Great job on the panels.