SIEZED PRESSURE WASHER ENGINE (part 2)

[@motoforlyfe]

You guy think it's gonna run? Let me know here!

[@seriesioo374]

I think it will run, but if it were me I would have separated the crank from that tight bearing and sanded/scotch brighted the surfaces. That being said put some Lucas oil treatment into it and that bearing will "self clear"

[@ontariofishing1790]

She will run.. it's a briggs

[@CarlMarx]

Yeah it'll run for sure

[@Tjousk]

yeah, fairly sure it'll run. Depending on the condition of that bearing, it might seize up again fairly quick, or it might loosen up more and keep running for another few years - as long as it's not run low on oil again.

[@66gtb]

It’s like watching a football game with 2 seconds left and the offense is on the five yard line and the tv breaks. We all want to see the last play of the game.

[@RustyGlovebox]

Made some good progress, looking forward to see if it runs and how long

[@nashguy207]

Great video good to see at roadkings with mike. See you saturday!!!

[@mikedoblo4782]

I got a champion lawnmower must be nearly 20 years old now has plastic cams and gears still going. it also got some strange thing to keep a valve open till it gets some speed up

[@joesinakandid528]

Called a pressure relief valve and it's used to make pull starting easier. Very common.

[@AntonBabiy]

Wow! A plastic cam.... That's a new one to me. Also the gasket sets the bearing clearance so that'll compensate for the slop from the chewed up bearing 😁

[@regsparkes6507]

I'd like to know why this engine seized,..was it a 'factory fault' or owner neglect,...i.e.. no oil change /checking oil level.?

[@Jamesb2433]

I’m working on the same engine and same issue with it.

[@snorman1951]

I'm going through this exact scenario right now. The washer sat for several years and now the engine is seized. I dropped the pump and I'm ready to open the crankcase cover. That camshaft bothers me. Is there any way to install it wrong? If so, how can I be sure to install it correctly? TIA

[@snorman1951]

Timing marks. DUH!

[@snorman1951]

It turned out the piston was stuck. Probably rust. Got it freed up, replaced a leaky fuel line, and cleaned the carb. It starts first pull now and the pump seems good. The wand needs replaced however.

[@williamheckman4597]

I regret throwing out my seized pressure washer engine after watching this. Doh.

[@colin_5839]

Nice! I would have thought it was the piston in the bore, but I guess not. Did you pop the head off camera to check for scoring? I'd just be curious to see what the bore looks like. I think that if it is only a bearing it will run fine for a while, be we will see! Nice video!

[@rattlin59]

What the hell happened at 05:42 !? Was like a dude with no head and his heart removed started tapping out the River-dance 😟😂

[@donaldpeyton2341]

Of course it will run, many years ahead. Why do these pressure washer required so much maintenance. Old time B & S lawn mower ran for thirty years, change oil, clean filter, and change the plug. Off to the races never need more then two pulls, usually started with one quick pull.

[@funbricknj]

if there was no damage to the cylinder and you have good compression. it should start. but whether it will seize again will depend on what seize before if it was a bearing in might seize again if you don't replace them eather way just make sure you fill it with oil before you try and start it

[@Ryan-uz2cr]

In my experience as a small engine mechanic Ive had tons of these junk china motors with broken governors that then lead the motor to over rev and seize up. Also lots with broken cam gears. Ive even had a Honda gx630 with only 400 hours come in with a broken plastic cam gear. Value engineering at its worst. Ill stick with my good ole American all metal flatheads...

[@chriholt]

What a teaser video! I think it will run fine, but plastic cam gear and plastic cam lobes? Good grief!

[@JSchrumm]

I think Roadking should watch your videos instead of giving you grief on his channel about not seeing you for a month and a half.

[@txsviking]

100% wing wang.

[@ROYALCOMMISSION29]

that motor is garbage i got the same one on a powerwasher and it broke, i can hear pieces moving underneat like piston 😂😂