my honda 4 stroke trimmer locked up. After watching your vid I emptied the fuel and oil tanks and removed the plug just like you showed. I was back up and running in 5 mins flat . Cheers from Qld
@rustyinspirations Жыл бұрын
That's awesome news 😃. Thanks for sharing 👍🏻😃
@kefwals8722 Жыл бұрын
Nobody can find their 10mm. It's an elusive creature.
@rustyinspirations Жыл бұрын
🤷🏻♂️😂😂
@barrygrant290711 ай бұрын
If you install about a 2-inch pipe in the drain hole with an elbow and plug on the end, you won't have oil running all over the place when you drain it. It will run right into the container. Don't know why manufacturers always put the drain right on the frame like that.
@rustyinspirations11 ай бұрын
It doesn't really bother me with how often it gets serviced. 😃👍🏻
@ironhorsenc1 Жыл бұрын
Just a note that I recently learned about hydrolocking my engine. When you are removing the old gas from the cylinder by pulling the starter lead, be SURE TO NOT HAVE THE SPARK PLUG LEAD ANYWHERE NEAR A GROUNDED POINT!! The gas/oil mix might ignite due to sparking. Could happen just saying. Learned that from a seasoned tech who must have had it happen in the past. Great video and thanks...
@rustyinspirations Жыл бұрын
Yes, A Very good point 😃👍🏻 cheers
@JakePlisskin129 ай бұрын
I have never had a problem finding my ten mil. I have so many. It's the 8mil I have a premium with..
@nbarrager5 ай бұрын
For me it was always the 13, and now that I'm not working on cars anymore it's always the 5/16
@muchgreatness7497 Жыл бұрын
I like the learning part but I mostly continued watching because of the accent....Mum, I did it for 'me kids' 🤣🤣
@rustyinspirations Жыл бұрын
😁 cheers mate. At least you enjoy it 😂👍🏻
@chrislnflorida51924 ай бұрын
Mine is froze up. I checked oil, fine, pulled plug, still cant pull it, checked if pressure of pump, still cant pull. Sprayed W-10 into Cylinder, now to crank with a wrench to see of i can move it. This is a Pressure Washer!
@rustyinspirations4 ай бұрын
G’day mate. Unfortunately a lockup engine isn't always a simple hydraulic lock fix. It could be the pull cord, Or it could be something internal in the engine And sometimes catastrophic. In your instance it could possibly be the pump its self that is locked up. You could test this by separating the engine from the pump to narrow down where the problem lies. 😃
@DonaldDuncan-u6j Жыл бұрын
Hondas r bad about flooding the cylinder with motor oil if the motor is knocked over even seen the better pressure washer 3000 psi or more fluid lock switch most of the. Time is hydraulic or motor oil inside the pump pressure adjustment that also can seize the engine
@rustyinspirations Жыл бұрын
Good point😃, yes I have also came across some Honda's with oil in the top end 👍🏻
@BloominOnion1 Жыл бұрын
nice vid, appreciate it. Neighbor's pressure washer is locked up, trying to troubleshoot.
@rustyinspirations Жыл бұрын
Best of luck 😃
@Ricardo-j3g9cАй бұрын
I should have watched this video before I wasted my money and the guy didn't even changed the oil. You live and learn.
@rustyinspirationsАй бұрын
That we do my friend. Hopefully it helps in the future 😃👍🏻
@ukqwerty9994 ай бұрын
Your jokes made me chuckle mate :) Got this fuel lock on a ride on, cheers for explaining how the carb is flooding the engine, will do this tomorrow. Hi from England 🌏
@rustyinspirations4 ай бұрын
🤣 cheers mate. I hope you get it back up and running 😃👍🏻
@petrobeets86785 ай бұрын
There maybe a screw in filter like honda and chinse copys filtee screws in from u der neath get torch look down in tank cap off if one there u will see bit of pai tank has to come off take notuce of way fuel line runs diection it goes if not u may squash fuel line cut fuel supply machine wont go lol i d iud it had to take tsnk back off rerout fuel line all good then
@rustyinspirations5 ай бұрын
Yes, you are right. it was an internal filter (inside the tank) It was missing. So obviously wasn't there from factors. I done a follow up video showing this 😃👍🏻
@SBRenos2 жыл бұрын
I’ve never had it happen to me, let alone twice.. But handy to know what to look out for 👍
@rustyinspirations2 жыл бұрын
You must put clean fuel in yours 😃 maybe I need a new system 😂
@RobertVernon-n3b Жыл бұрын
Pull rope on 2-stroke trimmer stuck until I removed the spark plug. Then the cylinder moves smoothly with no resistance. Assumed hydrolock. Drained the fuel and checked the carburetor, but as soon as the plug is re-inserted the problem returns. Any suggestions on how to proceed under this scenario? (By the way, when I checked the carburetor I found the air filter to be saturated with fuel.)
@rustyinspirations Жыл бұрын
G’day Robert, hmm 🤔 It sure does sound hydro locked doesn’t it. Did you find fuel in the cylinder? Being 2 stroke the air and fuel gets sucked into the crank case on the up stroke, so possibly fuel in there also. You might need to remove the plug again and turn it over while it’s upside down or on its side. Or Evan remove the carburettor to get the fuel out. Let me know how you get on 😃👍🏻
@leadnsteel1428 Жыл бұрын
Its weird i have Aspen fuel which is good for 2 years in it but it still wont start. Turned out their was water in the oil after it sat outside lol. I changed the oil and it started right up. Make sure to cover your stuff with a tarp or pastic bag.
@rustyinspirations Жыл бұрын
Definitely I Good point to at😃👍🏻
@josuelol4086Ай бұрын
What if my carb only has a drain plug ? The middle one is flat
@rustyinspirationsАй бұрын
I'd say it might just remove the bowl. But I can't be sure.
@DianaClark-m5iКүн бұрын
I have a generator that is hydrogen locked, so it has happened to me
@rustyinspirations22 сағат бұрын
@@DianaClark-m5i its very common isn't it 😃👍🏻
@chrislnflorida51924 ай бұрын
😂😂😂 its always the 1/2"-10mm that Always missing.
@rustyinspirations4 ай бұрын
10 and 12 for me 🤣👍🏻
@ImRemy_ Жыл бұрын
I only get one pull out of mine before it’s locked back up again and i have to take the pull cord cover off and manually spin it back in order to get another pull. Thoughts
@rustyinspirations Жыл бұрын
Gday mate. Apologies, Your comment sliped through. With out seeing it in person, this sounds like a pull starter issue. I'd say the recoil spring has disconnected or broken
@ImRemy_ Жыл бұрын
@@rustyinspirations no worries. Mine was hydro locked as well. I think mine had an issue in the valves/springs though bc after i had drained the oil and lubed the piston it was doing what i described before so i took the valve cover off to check how they were moving and the pull cord started acting normal.
@rustyinspirations Жыл бұрын
Awesome 😃, you've done well. Glad you got it sorted 😃👍🏻
@JohnBruno-yi1exАй бұрын
O god...i hope this is the case for my generator
@rustyinspirationsАй бұрын
🤞🏻😃 wouldn't that be good 😁
@stephaniebrown3725 Жыл бұрын
I think I have the same issue, however after draining the gas and removing the spark plug, my cord is still stuck. I can't pull and force gas out of the whole where the spark plug is. Does that mean I'm not experiencing hyrdolock on my pressure washer?
@rustyinspirations Жыл бұрын
Hi Stephanie, Correct your issue may be with the pull start it’s self.
@DonaldDuncan-u6j Жыл бұрын
L
@shanegent58042 жыл бұрын
Awesome informative video, I never thought of the importance of turning the fuel tap off…every day is a school day ! When I change my oil, much like your method, I get a bit of masking tape and run across the bottom of the engine under the oil plug so to stop oil getting under the engine when draining the oil….that’s my 5 cents worth 😂 Enjoying your content, keep it up 👍
@rustyinspirations2 жыл бұрын
g’day Shane, That’s a good idea😃👍🏻
@deebee39018 ай бұрын
Great video mate! Lovely to see someone take pride in their work and do things properly. Nice workshop BTW.
@rustyinspirations8 ай бұрын
Gday deebee😃, thanks mate. You should see the shed at the moment 🤦🏻♂️ It is actually about to get extended. Can't wait. Stay tuned to see me set up my new workshop in the near future 😃👍🏻
@MasiMoreno2 жыл бұрын
You just reminded me that I already have to change the oil in my lawnmower. 😍👍
@rustyinspirations2 жыл бұрын
😃Good preventative maintenance 👍🏻
@nephatsibanda-cz1ry Жыл бұрын
Hello sir my generator olso stacked what can l do to get it running
@rustyinspirations Жыл бұрын
G’day Nephat😀, I’m not sure mate. It can be really hard to diagnose without looking at it in person 👍🏻
@sekovittol3124 Жыл бұрын
Yep, the famous missing 10mm socket and or wrench. 1:42
@rustyinspirations Жыл бұрын
😂you know what’s up 😃👍🏻😂😂
@msstar830 Жыл бұрын
Thank you so much for this video. I was able to fix my pressure washer after being frustrated at not being able to start it.
@rustyinspirations Жыл бұрын
That's awesome news 😊👍🏻
@LawnLads2 жыл бұрын
great informative video mate.
@rustyinspirations2 жыл бұрын
Cheers lads 😃👍🏻
@jeffmays71928 ай бұрын
Took out my plug. She pulled great. There was a bit of fuel in there but very little. Pulled and pulled till she was clean . Put the plug back in and no change. Did this procedure 3 times to no avail when plug goes in she’s locked up.
@rustyinspirations8 ай бұрын
That's very odd 🤔 I have absolutely know idea. Definitely the right plug? It's not to long and fouling the piston?
@devinthompson1534 Жыл бұрын
Yeah I’ve done all of this even tried the magic oil down the spark plug hole. When I put the spark plug back in it locks. I’ve even taken off the carb and cleared the fluid. Only 1 month old engine. The gas did flow to the oil and got into my filter, I removed filter and changed oil still locking up when I put the spark plug back in. When the spark plug is out I can pull it though. I’m very confused on what to do next.
@rustyinspirations Жыл бұрын
Gday mate, the only two things I can think of is the spark plug being go long and fowling the piston. Or it's not completely dryed out and is still hydro locking? Sory I can't be of more help 😔
@devinthompson1534 Жыл бұрын
@@rustyinspirations does it have to be completely dried out 100% because I see people poor magic oil down the spark plug hole and they can pull and start the engine. Also the spark plug being too long? What could this mean, it’s all OEM off the engine. Thanks in advance.
@rustyinspirations Жыл бұрын
If the plug is genuine, This wont be an issue. You don't want any fluid in the top of the cylinder, only vapour. What is the magic oil? Fuel?
@devinthompson1534 Жыл бұрын
@@rustyinspirations the magic oil is oil technically. Something people use when they get stuck because the gears aren’t lubed or something like that. I guess when you poor it down the spark plug hole it’ll eventually loosen up the crankshaft. There’s videos on KZbin everywhere on it. So no fluid at all on the top of cylinder? So is it possible because it’s slightly wet that I can’t pull when I put spark plug in?
@rustyinspirations Жыл бұрын
Got ya😃, are they putting oil down the plug hole because the engine is seized? I have done this many times in the past also. However your engine doesn't sound to be seized as such. The fact that it turns over while the plug is out confirms this. In wondering if the little bit of oil you are putting down the plug hole is just enough to hyrolock the engine? Sorry if im not a lot of help. It can be very different diagnosing something that I can't actually look at 😂
@87GP400 Жыл бұрын
Thank you so much. This is what I needed to know for my stump grinder with Honda engine !
@rustyinspirations Жыл бұрын
No dramas, thanks for the feedback. 😃
@jasonlammas53412 жыл бұрын
Great vid try the tomato sauce lid on the oil bottle never need a funnel again.
@rustyinspirations2 жыл бұрын
Cheers Jason,I’ll definitely do that 👍🏻👍🏻
@dodgeguy999Ай бұрын
Awesome , Thank you so much very informative , My customer brought me his 6.5 CR950 Briggs Yesterday, Its was doing the same thing Fuel dripping on my shop floor. I have heard of hydro loc , But never seen one, His complaint was its hard to start. The fuel was left on. Can't wait to go over it tomorrow. Your video was spot on. Thanks so much.
@rustyinspirationsАй бұрын
Thanks mate, I hope it worked for you 🤞🏻😃
@dodgeguy999Ай бұрын
@@rustyinspirations Thank you Sir. Nah it has other issues lol.
@robert-zj7ef6 ай бұрын
Im not a mechanic so I don't know what you mean when you say bottom end. Is your point that the oil needs changing?
@rustyinspirations6 ай бұрын
Gday Robert, the bottom end is the crankcase, (everything below the cylinder and piston) The crank case contains oil to lubricate the bottom end. Although after time the oil can become slightly contaminated with a small amount of fuel that makes its way past the piston rings. In this case it was exssesive, to the point it had actually increased the oil level. This much fuel will thin the oil and possibly not lubricate as intended. I hope this answers upu question. But feel free to ask more. I'll do my best to answer them 😃👍🏻
@top6ear Жыл бұрын
Oh my god this is exactly what's going on with my snow blower.
@rustyinspirations Жыл бұрын
G,day jake😃 Awesome mate I hope it helped you get it sorted 😃👍🏻
@michaelwheatley72578 ай бұрын
This has happened to me but not sure if it's the fuel though. I will be doing the same to see if it is. I will let you know
@rustyinspirations8 ай бұрын
Fingers crossed mate 🤞🏻😃. Absolutely, keep me posted
@thegreenandgoldlife14642 жыл бұрын
Good boy with the gloves. Something I do not do, but probably should
@rustyinspirations2 жыл бұрын
Definitely should, I’m the same mate. I need to change my habits😃
@mickaweapon10 ай бұрын
Excellent video. I am looking forward to trying to fix my neighbors small engine for his snow blower with this information.
@rustyinspirations10 ай бұрын
Awesome. Hopefully this is the issue. Please keep us posted 😃👍🏻
@themowerman2 жыл бұрын
Good tips mate
@rustyinspirations2 жыл бұрын
Thanks mick 😃
@GT-jp4bo Жыл бұрын
Wow awesome my brother from Texas USA 🇺🇸
@rustyinspirations Жыл бұрын
Cheers mate 😃👍🏻
@FUNNYVlDS Жыл бұрын
Thank you for the video truly
@rustyinspirations Жыл бұрын
And thank you 😊
@robert-zj7ef6 ай бұрын
Your video was very informative. Im certain I can now repair my prrssure! Thanks!
@rustyinspirations6 ай бұрын
Please keep me posted 😃👍🏻
@robert-zj7ef6 ай бұрын
@@rustyinspirations Going to the laydown yard this morning. Ill post my results.
@mada6582 ай бұрын
Thanks so much ..I had the same problem.
@rustyinspirations2 ай бұрын
Not a problem. I'm glad you got it sorted 😃👍🏻
@ontimeconstruction76215 ай бұрын
Very educative
@rustyinspirations5 ай бұрын
Thank you 😃
@Crushin_Libs Жыл бұрын
Had an engine come in for service and the entire crankcase was filled with gasoline. Yikes.
@rustyinspirations Жыл бұрын
G’day Preston 😃. I’d believe it 😃🤦🏻♂️👍🏻
@Crushin_Libs Жыл бұрын
@@rustyinspirations appreciate your video! Subbed for sure!
@rustyinspirations Жыл бұрын
Cheers Preston😃. And I appreciate your sub 😃👍🏻👍🏻
@unclebrentsshed4253 Жыл бұрын
Nice work brother 👌🏽
@rustyinspirations Жыл бұрын
Cheers Brent 😃
@Bl00DmixedWithPoison Жыл бұрын
U aussie or from nz?
@rustyinspirations Жыл бұрын
South Aussie mate 😃👍🏻
@Bl00DmixedWithPoison Жыл бұрын
Your snowblower video helped me save my $850.00 usd snowblower. Thanks a lot bru, 🍻