Simple DIY Medal/Sport Display Shelf

[@sumandalal2175]

best diy i ever saw

[@beauhornerarmwrestling5723]

I like it!💪🏼

[@howtofixitworkshop]

Thank you!

[@DayuSingh]

I really liked your idea. But what about medals getting tarnished?

[@howtofixitworkshop]

Thank you, haven't had any problems with tarnishing

[@theol3130]

How long is each wooden dowel after cutting? 2 inches or 3?

[@Peterdimp]

A little explanation of the steps would be nice for this video.

[@TheShaggyfrog]

Thanks for the video. What did you use to end up hanging it flush on the wall?

[@howtofixitworkshop]

No problem! We just used a few 2 inch screws held into the drywall with drywall anchors

[@TheShaggyfrog]

@@howtofixitworkshop did you notch into the back of the shelf and hang on the screws or drill through the whole shelf? Thanks for replying!

[@howtofixitworkshop]

I drilled through the shelf itself. Just measured out the screws in a straight line. They end up being mostly hidden by the medals

[@grpere1]

Very cool. How far did you measure on your first cut for the two side pieces. It looks like five and a half inches but I cant tell.

[@fireroadie6654]

Very very nice. 👍👍

[@howtofixitworkshop]

Thank you!!

[@fireroadie6654]

I did something very similar a year ago and we have had a blast adding to it more medals 🏅 and bibs and nick nacks from races. Do u have a update video of this video??

[@TheGaspar1000]

How far apart did you measure the dowel rods?

[@howtofixitworkshop]

I think about 2 inches

[@journeythroughdarkness]

would love to try building this for my niece however i do have a couple questions. First of all great looking project, nice job! How did you use your pocket hole jig (how many holes, spaced apart, etc) and what kind of screws did you use to attach the boards together using the jig holes? Also when drilling the dowel holes, did you drill all the way through the back of the board or only part way? Thank you very much, take care.

[@howtofixitworkshop]

Thanks for the feedback! For the medal display we didn't use any pocket holes. All of the wood was attached with wood glue and brad nails. The holes for the dowels were drilled approximately a half inch deep and we used wood glue to hold them in place. Hope this helps!

[@journeythroughdarkness]

@@howtofixitworkshop have made 2 since these comments. Thanks alot man! just bought a router was wondering if keyholes would work on the back instead of drilling through it. Have you tried?

[@howtofixitworkshop]

That's a great idea! I haven't tried keyholes but I think that would work just as well!

[@surenderssubramanian4293]

Looks awesome watching 3rd time. I want to do same as like this.. Can you tell me the measurements? Length, height what s the gap you maintained?

[@howtofixitworkshop]

I believe it is a 6 foot 1x6 inch pine board. The spacing between holes is 2 inches. Thanks for watching!!

[@surenderssubramanian4293]

@@howtofixitworkshop thanks for the reply.. love from india...

[@katkat4762]

How did you attach it to the wall? That part wasn't in the video.

[@howtofixitworkshop]

Sorry about that. I simply screwed the medal rack to the studs in the wall, through the rack

[@shafiqabbadrehman5904]

you work hard to make this video for us but its really not bad

[@howtofixitworkshop]

Thank you?

[@iopyyjsbkk1886]

❤❤❤❤❤

[@sumandalal2175]

ty

[@howtofixitworkshop]

You're welcome

[@Hypergamer431]

Prize

[@howtofixitworkshop]

Yep

[@727MiX]

"DIY"...if you have every power tool known to man.

[@howtofixitworkshop]

Nah, just a drill, hammer and hand saw

[@Royalslugger]

Cool display, but no instructions on build, so definitely not a good how to video.

[@howtofixitworkshop]

Yeah we've experimented over the years with how much info to share, some say too much, some say too little...Thanks for the feedback!

[@apelsin6923]

Крута

[@YTFais-ev3ye]

free palestine