Great video. It would be great to see physical wiring being done on remote estoppel etc. Not all get the chance to do that type of work. Great ref point.
@williameunson2013Ай бұрын
great simple video i can understand thank you
@GSHElectricalАй бұрын
@@williameunson2013 thanks for the positive comments
@eriaudaniel83602 жыл бұрын
Am so grateful for your videos. they are of great help for my success as in my projects. Thank you for sharing your knowledge with the world
@GSHElectrical2 жыл бұрын
Thanks for the support and watching. 👍🏻Gaz
@ramzg54023 жыл бұрын
Thanks a lot for this amazing video.
@Xxxcappie233 жыл бұрын
This is a very good video. Thank you gents
@chintanraval10123 жыл бұрын
Thank you very much 🙏🙏
@danielteyehuago16333 жыл бұрын
Thanks for sharing it with us
@GSHElectrical3 жыл бұрын
Thanks for watching and commenting 👍🏻
@bigashelectrics2582 жыл бұрын
Wish I found this great video a couple of months ago 🤦♂️
@GSHElectrical2 жыл бұрын
Come on Big Ash I have over 500 videos you must have watched most of them 😃👍🏻
@bigashelectrics2582 жыл бұрын
@@GSHElectrical Of course but this one much of just slipped through 🤪
@ermVice Жыл бұрын
What are contacts 97 and 98 used for?
@brianhewitt86183 жыл бұрын
Thank you
@andysims49063 жыл бұрын
What no Dashpots . Great video by the way
@Hiccup773 жыл бұрын
On my AM2 i did the calcs from the faceplate and incorporated the p.f i told my examiner I was doing it this way and he was fine. Think they chould make it a bit more difficult, by having you choose the correct rated contactor with the correct coil voltage. 2 wires to connect did not show skill in wiring a dol.
@MotherRussiaisforever2 жыл бұрын
If had the diagrame for the schematic it really helps, the shematic you can follow much easy , in this case you have to go back to the old vidoe whole diagrame but in the case of schematic even if someone does not understand it he or she can still wire it actually.
@ABD56678 ай бұрын
I just got a dol starter, been using a more advanced pump starter but them being finicky and burning out too easily. The dol starter was already wired up, it's a 3 phase. It's quite complicated opening and seeing all these wires
@adamsoltys5307 Жыл бұрын
When purchasing these contactors ,there is a short link between terminal 14 and A2 directly below,What is the purpose of this and should it be removed if wiring up like shown?Thankyou.
@sparksparky95923 жыл бұрын
Excellent video, have you done a video on the same three phase motor.
@Hiccup773 жыл бұрын
3p is pretty much the same. Apart from the neutral goes direct into A2 of the coil L1L2L3 in T1T2T3 out.
@Jack-zr4lm2 жыл бұрын
Can you explain why you have to loop the neutral back round through the contractor again and not straight into the motor?
@GSHElectrical2 жыл бұрын
Hi the answer is in this video 👍🏻 Single Phase Direct Online Starter DOL Wiring Diagram Connections Explained kzbin.info/www/bejne/bYaQdaSBhtCGhrc
@craiggreenhalgh1082 Жыл бұрын
Hi Guy's, I've Purchased A Pre Wired On Line Starter With Overload, The A1 Is Linked To L1 & A2 Is Linked To 13, After Watching These Videos I'm A Little Confused? Any Ideas Welcomed.
@Pancakepicnic18 ай бұрын
How do you figure overload setting out when it’s not written into the specifications?
@cupofcoffeeinthebigtimeyea3485 Жыл бұрын
Where would I connect my two wires coming front the compressor pressure switch?
@Letitbe-042 жыл бұрын
i got a dol starter,sprecher & schuh.it has the phase going into L1 & out on T3 to motor with T1-T2 .& L2-L3 linked, strange that the manufacturer puts the phase thro the relay as opposed to you running the neutral thro,...also 95 is internally permanently linked to A2 of the coil. 7the
@paul_my_plumbs_uk3 жыл бұрын
👍👍👍
@andrewschroeder54412 жыл бұрын
Can I convert my existing 220 wiring to 115v?
@sukruaridil51942 жыл бұрын
Can we add one more motor for that system?
@hiramkhackenback2 жыл бұрын
not advisable
@HagerFikerTeater11 ай бұрын
Time 03:45 normally open is not stop button..can you check it…
@duncanndirangu9998 Жыл бұрын
What about number 98
@marcinc36625 ай бұрын
there was no 97 98 connected on the drawing
@ionutth48952 жыл бұрын
Sadly i dont understand anything in that messy box, its much easier to take everything apart use drawn schematics to explain the connections then wire everything one by one and explaining using the drawing. I saw this on an Udemy course and it was very easy to understand, i understand the idea behind the contactor > Overload > auxiliary contacts and coil power going through the overload before going into the contactor but the little box is too messy and hard to follow what is happening in there.
@GSHElectrical2 жыл бұрын
Motors, Starters, Controls, Remote Stop Start - Single and 3 Phase kzbin.info/aero/PL2Ea5r9gxUUfv51Ld1UlNGR39rfFIExTU