Whelen Siren - EPSL1 Epsilon Series 100 Watt Siren

sirennet.com/whelen
The Whelen EPSL1 Epsilon Series 100 Watt Siren provides a wide range of features in a low cost siren that meets SAE Class A sound requirements and is California Title 13 compliant. Epsilon provides hands-free operation, public address, Scan-Lock multiple warning tones and real time diagnostix. The front of unit includes a PA volume control knob for the noise cancelling microphone, an On/Off switch, a manual button and a 7-position tone/radio rotary switch.
Features:
Full featured, self-contained electronic siren.
100 watt amplifier.
LED Backlighting.
Real-time diagnostix indicator:
Steady light: the siren is operating correctly.
Single flashes: speaker is short circuited.
Indicator off: speaker is not at full output.
Nine Scan-Lock siren tones to choose from: Tone off, Wail, Yelp, Airhorn, Hi/Low, Piercer, Y249, Manual wail coast to stop and Manual wail stop.
Wail, Yelp, and Y249 are California Title 13 compliant tones.
Meets SAE Class A sound requirements when used with most 100 watt speakers.
Meets California Title 13 requirements.
Hands-free operation/override from the horn ring.
Scan-Lock switch is "security" located on the rear to ensure all fleet sirens are set with the same tone sequences.
Installation package includes all the necessary mounting hardware and input pigtail connector.
Rotary switch allows choice of standby for use with the manual button, manual tone 1 & 2.
Hands-free position allows horn ring operation of the siren and tone 1, 2 and 3 positions.
Each of these tone positions has an override tone when the manual button is depressed.
Pre-wired with quick disconnect plug for easy service and prompt replacement.
Specifications:
Input voltage: 12.8 VDC ±20%
Input current: 8 Amps Max.
Input fuse: 10 AMPS
Speaker impedance: 11 OHMS Min.
Operating temperature: -30° C. TO +60° C.
Storage temperature: -40° C. TO +70° C.
Humidity: 99% (Non Condensing)
Output voltage: @15 VDC @11 OHMS 34 V RMS Max.
Output power: @15 VDC @11 OHMS 105 Watts Max.
Dimensions: 5-7/8" W x 2-1/4" H x 5-3/4" D.
Whelen Twenty-four Month Warranty

[@unit_10]

Awesome demo!!!

[@SIRENNET]

+WILLY vs WALLY Thank You Very Much :)

[@Gingibus]

I like that!

[@DMAXRYNO]

Can the Manual button on the face be wired up to a separate button? That way the entire unit can be mounted out of reach and just have one manual momentary button on the dash? I'm sure it voids the warranty, but does anyone have an answer?

[@davidanstine4476]

there's is this one ambulance company where I live and the must have three or four siren speakers on their vehicles because they always have so many siren tones on at once.

[@johndriscoll3782]

Signal vehicle products makes a siren amplifier that can put off set tones through two speakers if you look up svp magnum siren on KZbin there is a demo of it

[@cjolney]

They most likely have the Whelen 295HFSC7, which is a dual tone 200W siren unit.

[@TheAbbe89]

Nice. I´m wondering about a model called Whelen Beta Martin . Can you do a demonstration about it?

[@SIRENNET]

Martin is one of the tones Whelen includes in the BETA112R Amplifier, as well as many of their other siren units. It's more common known as the Euro-tone. If you skip to 5:10, you'll hear it for a few seconds.

[@blackbear9878]

@SIRENNET since this siren needs 12.8 volts input, would it drain my stock 12 volt battery? or would i need to add an additional battery to my vehicle?

[@SIRENNET]

You'll be fine using your stock battery.

[@mechanicalengineering9792]

Wiring diagram pliisss

[@RRRR-my1ge]

how can I connect the Whelen speaker to the unit? Doest it come with the connector you showed? Which color wires do I attach the speaker wires too? Thanks

[@SIRENNET]

The speaker will connect to the Green and Yellow wires on the Epsilon input harness. Yellow goes to the speaker positive wire and Green goes to the negative. We used our own connections, they're not included. You can use butt-connectors, quick-connect terminals or soldier the wires together.

[@fcruzin22]

I have one of these and it turns on milli second and turns off. If anyone could help me troubleshoot it I would greatly appreciate it. Thanks

[@SIRENNET]

If you haven't already, check the Ground and Power wires. Perhaps one has come loose. Is it new, or have you been using it for a while?

[@znovosad555]

As nice as these are, they still don't beat the old mechanicals and electronic sirens

[@SIRENNET]

+znovosad555 The conventional Q is definitely one of a kind. It is quite nice to be able to simulate the Tone for small Applications when needed.

[@znovosad555]

+SIRENNET do you recommend your siren speaker with this? Or would the Whelen one be best with it?

[@SIRENNET]

To be honest, either one will work perfect along with the Epsilon. Our SNSP1 does have Vehicle specific mounts that can be used along with it to ease installation.

[@znovosad555]

+SIRENNET one other question, would the epsilon be able to flush mount to a custom made console made by myself, or would I have to mount it with the bale bracket to the front of the console?

[@SIRENNET]

The easiest means of adding the Epsilon in your custom console would be to use one of the face plates that made for console drop-in mounting. For face plate details, please feel free to email our Team at: [e-mail].

[@schnuurtchke]

Zazur zambulance

[@justinoh3122]

first comment :P

[@sebastianadhi3066]

Do u have whelen alpa sl

[@SIRENNET]

We sure do. Please visit our page here: sirennet.com/store/product/whelen-alphasl-200-watt-remote-siren

[@sebastianadhi3066]

SIRENNET how price epsilon?

[@SIRENNET]

For current pricing, please see our Epsilon product page via: sirennet.com/store/product/whelen-epsl1-epsilon-series-100-watt-siren