Six Amazing Projects Using SCULPFUN S9 Laser, happy laser making at home. Laser Engraving Machine

[@MnACreations]

Excellent video demonstrating the S9 and providing some tips and ideas.

[@marcovicino8521]

Hello! fantastic video! i have sculpfun s9 but when i try to remove varnish i see small line in my design...the varnish is not completly remove...how can i do? i use power 10%, interval 0,08 and velocity 40 mm/s...

[@kya8721]

Pls give me setting of the stainless steel 😢

[@adianajayatrading4406]

Can cut n engrave rubber sheet for rubber stamp

[@gypsyofcruzz]

Someone knows the settings for the cat portrait ? Power and speed

[@bunudemine7840]

Hola, gracias por las ideas. Un saludo.

[@cwai79]

Is it suitable for picture engraving on thin material surface?

[@007JHS]

Some great ideas...! Thanks.

[@SCULPFUNReal]

😆😆

[@Georges-MILLION]

Super démonstration ! Merci ! Great demonstration ! Thank you !

[@VasileSamuelCircu]

Ciao. Come si fa mettere a fuoco? Io uso lightburn. Grazie

[@HybridlifeOrg]

With the settings used it would have been great

[@adeilsonvieira2263]

Tenho uma S30 Pro, essa empresa só quer vender não dá nenhum tipo de suporte aos clientes, e quando perguntamos algo eles respondem outro assunto aleatório, arrependimento total.

[@theolasvegas]

Where did you buy the air assist nozzle that you added?

[@SCULPFUNReal]

Factory processed. The new version of the S9 laser head has it.

[@mangjose03]

Would you mind to share how long the engraving would take?

[@Csriñositokarateka24]

My s9 can cut 4mm white acrilic?

[@fredericmuller7371]

Please explain how to have a circle round 😢

[@Dancopymus]

Hi friend, thanks for the great video; I have a few questions: 1) What kind of ink did you use in engraving the Stainless Steel? (I have the xTOOL D1 Pro 10W, and I did a test of that but did not use ink). 2) On the Tile, are the three layers of paint you apply water-based? 3) Finally, what settings do you think I should apply (Tile), using a 10W laser? Thanks

[@党一哲]

1.Sculpfun 10W laser can sculpt stainless steel without hacking（9mm/S，100%） 2.If the parameters are accurate, it is enough to spray only a layer of black paint 3.kzbin.info/www/bejne/inubm2V4l9OgbKs Spray a layer of black paint evenly. Then refer to this video, use the gradient test picture, set the width at least 100mm. The paint is easy to sculpt, so the speed can be faster, and the power is not need too high. You can test the accurate parameters yourself.

[@党一哲]

What speed do you often use with XTool?

[@Dancopymus]

On a Stainless Steel pendant: Power = 100%; Speed = 3mm/s; Pass = 1 (directly, without any paint). On acrylic, I haven't tested it yet.

[@veepho]

Can cut Rowmark ?(sheet plastic)

[@SCULPFUNReal]

Yes,

[@veepho]

@@SCULPFUNReal I cannot connect with Mac Monterey you can help me

[@SCULPFUNReal]

@@veepho you can ask [e-mail] for help.

[@veepho]

@@SCULPFUNReal Thanks.

[@anthonymontemayor6134]

Hi! can this machine cut transparent acrylic?

[@SCULPFUNReal]

she can't , need to use CO2 laser. Diode laser is good at cutting wood or black acrylic.

[@anthonymontemayor6134]

@@SCULPFUNReal is it bad to use 100% power? I'm cutting plywood with 4 to 5 passes and 100% power, at 400mm/m speed

[@SCULPFUNReal]

@@anthonymontemayor6134 80% power is also ok. Only wait a longer time

[@anthonymontemayor6134]

​@@SCULPFUNReal Does using 100% power shortens the lifespan of the laser diode?

[@SCULPFUNReal]

@@anthonymontemayor6134 only a little influence, diode laser is much longer than CO2 laser in lifespan

[@joshuelicasartscrafts1250]

Why my engraving produces vertical line, though I engraved it horizontally..

[@SCULPFUNReal]

You should check the software setting

[@joshuelicasartscrafts1250]

@@SCULPFUNReal im only using lasergrbl.. what setting should I fix?

[@joshuelicasartscrafts1250]

The engrave look like it has the texture of the belt..

[@SCULPFUNReal]

@@joshuelicasartscrafts1250 vertical or horizontally can be adjust, you can search on lasergrbl website

[@3djulien]

Merci pour la démo

[@stevegrant6464]

Settings?

[@FernandoNeri7]

what is the setting to cut 6mm mdf?

[@SCULPFUNReal]

6mm MDF is hard for 5W laser, you can try SCULPFUN S10 laser

[@MarcDanielsMusic]

It can cut mdf?

[@SCULPFUNReal]

It can be cut about 3-5mm, but it is very easy to burn black, which affects the cutting efficiency. But our next generation products can solve this problem.

[@MarcDanielsMusic]

@@SCULPFUNReal cause I have this model and the kit expansion and I bought to do guitar templates on MDF. Wich parameters you recommend to cut MDF of 5? Thank you

[@SCULPFUNReal]

@@MarcDanielsMusic 100% power , 3mm/s

[@maroildofilho5826]

Friends, send the Rotary Roller with 360 to the warehouses with stock for Brazil! .... PLEASE

[@SCULPFUNReal]

you can try alibaba, mtw.so/5UGFjw

[@Jer0867]

Interesting video....but spoiled by that annoying "rave music" which does nothing to improve it. Why is it used? I just can't see the point. Only kids or teenagers would enjoy this kind of rubbish.