SKD #30 - TUNDRA BEDSTEP BUMPER STEP INSTALLATION 👀😮😍 UPGRADE EASY & QUICK TIPS

[@SKD_4830]

LIKE, COMMENT AND SUBSCRIBE‼️‼️

[@Tobstertacoma]

Thanks a TON! This is the best video out there with the short cut added.

[@SKD_4830]

@@Tobstertacoma glad this video is helping so many people 💪🏽👍🏽 and thank for the comment

[@Johnson-Sequoia]

You saved me tons of time! Thanks

[@SKD_4830]

@@Johnson-Sequoia 💪🏽💪🏽thanks for the comment and glad I could help 👍🏽👍🏽

[@bryanbowers5491]

Dude, the tip to just cut the factory bracket worked like a charm! You saved me hours of time, thanks!

[@SKD_4830]

I’m so happy for all the comments like these 🙏🏽 💯. Have a blessed day 👍🏽

[@BritannyDuhh]

Salute 🫡🫡🫡🫡

[@SKD_4830]

@@BritannyDuhh 👋🏽🙏🏽🫵🏽

[@BadBoy4U]

Hey, how is the bed step holding up? I’m getting ready to pull the trigger on one for Black Friday and wanted to see how good it’s held up.

[@SKD_4830]

@@BadBoy4U holding up fine👍🏽 I don’t think you will go wrong with this purchase💪🏽

[@BadBoy4U]

@ ok thanks. I appreciate the quick reply. Much appreciated!

[@seahorse4678]

Great video, my friend. I just installed mine today. The instructions are not that great, but when I see you cutting the original braket, I did the same, but without removing it, it saved me lots of time. Thanks for the video.

[@SKD_4830]

That’s great👍🏽. Glad I could help with this video. Thanks for the comment and feedback.

[@butchtaylor5086]

Nevermind! I see that you did use it! Great helpful video!

[@SKD_4830]

Ok no problem 👍🏽

[@ivan2056]

Thanks for the Vid! Helped me tremendously!

[@SKD_4830]

@@ivan2056 glad I could help👍🏽💯

[@panathrasher]

This is a very informative video. The step by step could use a few more details, but you more than made up for it with the bracket shortcut. I also cut the original bracket while it was still on the truck, and that saved a lot of time as well as simplified the installation. Thank you!

[@SKD_4830]

Thanks for the comment I really appreciate you 🙏🏽👍🏽

[@ryanb5442]

Thank you for sharing the shortcut! I was looking at the assembly and was wondering if I could utilize the stock bracket. You confirmed what I've been thinking of doing with the install. This will save so much time. 👍

[@SKD_4830]

Awesome thanks for the comment and glad this made it to you in time.

[@250plate]

just did mind, i just cutting the bracket while on the truck. thanks for the video and advice!

[@SKD_4830]

Sweet👍🏽💪🏽 no problem and thank you for the comment.

[@southernrrman]

Thanks Brother! Saved me a lot of work!

[@SKD_4830]

No problem🙏🏽. That’s awesome, had to find a easier way 👍🏽 for the community

[@elong35]

Found your video after trying to pop off the bumper cover… then your tip tip cut the existing piece! Boom! Thanks man!!!!

[@SKD_4830]

Glad I could help and thanks for the comment 👍🏽

[@user-by3ii4ec1n]

Thank you! I was struggling to get the bracket in.

[@SKD_4830]

@@user-by3ii4ec1n glad to help 👍🏽 thanks for the comment

[@butchtaylor5086]

Sorry to keep bugging you but if you cut and use original bracket do you still have to use the strap part you placed beside the little spacer part? Thank you so very much!

[@SKD_4830]

It’s all good not a problem but I see that you got it now

[@WaymondJr]

This is an awesome video man, just awesome ❤😎👌

[@SKD_4830]

Thanks

[@lindaflorian5486]

Thank you for the tip my friend!!

[@SKD_4830]

Glad I could help, thanks 🙏🏽

[@kevinjcooper]

Great idea cutting the Toyota bracket. After seeing where you cut it, I was able to cut the same spots right on the truck, which eliminated so much extra work. My only slow down was that I installed the angle brace upside down the first time and quickly realized it wouldn't get all the way to the bed panel attachment point. Overall great job. Thanks SKD_4830.

[@SKD_4830]

Thanks it’s comments like these that I enjoy. We have to help one another if we can. Thanks again for the feedback

[@dougm.635]

So to bolt this up after cutting bracket (on truck), can you do it all from underneath witout having to take bumper end off? thanks

[@SKD_4830]

Yes that’s what I was trying to say at the end of the video. You can install this bracket without taking the bumper apart 👍🏽

[@butchtaylor5086]

Would an angle grinder be too clumsy to cut the bracket while it is on the truck? Apologies for my ignorance!

[@SKD_4830]

Use what is comfortable for you. I used what I had which was a Dremel.

[@lennyperry6210]

If you cut the bracket while on the truck, no need to tape corner and remove bumper plastic, right?

[@SKD_4830]

Right. I forgot to make that clear in the video l. Thanks for the comment and please subscribe if you haven’t already. Thanks again 👍🏽

[@thfourme]

Hello…great install video👍 One question…does your truck have the resin rear bumpers? I have a 2019 limited and have them …just want to make sure I don’t have to do any cutting on it besides the bracket bottom ? Thank you 👍

[@SKD_4830]

I think. They are the colored match bumpers front and rear, that comes on the platinum tundras. Thanks for the comment and sub 👍🏽

[@wiscowalleye7954]

Great video thanks!! Does the step work with the tailgate down?

[@SKD_4830]

Yes it does work with the tailgate down. Thanks for commenting and please subscribe if you haven’t already.

[@cathypost602]

what name brand step are you useing?

[@SKD_4830]

Amazon purchased (ZONFANT Rear Bed Step, Retractable Side Tailgate Step Compatible with 2014-2021 Toyota Tundra, Replace#PT392-34140 75316-01A)

[@Jeffc288]

I was lazy and snipped the sides and bent it up.

[@Jeffc288]

Also, Why’d you tape it? I’m confused

[@SKD_4830]

Was going by instructions when I did it. Tried to let my viewers know that if I was to do it again I would not follow the instructions. I would just cut the bracket and install the step without taking bumper loose or bracket off.

[@Jeffc288]

@@SKD_4830 that’s basically what I did. Lazy but efficient lol

[@BenIsraelDavid]

I need one of those for my truck

[@SKD_4830]

Yeah man, anything to make it easier to get into the bed of the truck

[@BenIsraelDavid]

I want a F160

[@SKD_4830]

Is that a new model? What’s that? Lol 😂

[@SKD_FAMILY]

❤👍🏾

[@SKD_4830]

Thanks family ❤

[@butchtaylor5086]

Very confused (it’s not that hard to do!) what was all that instruction about #2 and #3 regarding bumper caps? That’s the only part of the install that I did not understand, but you did not show that? Sorry to be so dumb but what am I missing, please?

[@SKD_4830]

I started by following the bumper step instructions, but halfway through I decided to use the original bracket because the bracket included in the package was flimsy. So, I cut and used the original bracket which was more sturdy. Then I tried showing in the video that I didn’t have to remove the original bracket from the truck. All I had to do was cut it while it was on the truck which would have saved me a lot more time.

[@butchtaylor5086]

Thanks for your prompt and gracious responses!

[@SKD_4830]

@@butchtaylor5086 thanks for the comments and hope that this video was able to help you with your project.