Skidoo 850 Secondary Clutch Roller Replacement And Test Runs!

[@jeffcarine9108]

Absolutely love watching your videos humor mixed with knowledge

[@CP-lj8ob]

3/32 punch for the roll pins. Always replace stock rollers with the ones from HI-Torque located out west. That pin on the chaincase should not be pulled it looked like it was in the wrong spot.

[@PolarisEricson]

Tech tip for the 850 guys. Rollers snap when you go from reverse to forward and you slap the rollers. Ease into it when going from reverse to forward

[@ChrisLohr-u1b]

I'm very impressed with your clutch rebuild skills

[@D00640ER]

Hey Pete and Jim, this is perfect timing to put out this video. I'm right in the middle of tearing into my 2011 Legend 600 Etec with broken rollers! Awesome to see the step by step process before I get deep into it. Thanks for adding the humor also! Always good info with laughs thrown in. Think snow!

[@tedneitzel]

Excellent work as always! She dangles!

[@jordancaleb5790]

Great shots and editing! Always enjoy how too vids as well even for a sled i dont own, its all great information that can be re applied in lots of ways😊

[@calcobb442]

Enjoyed the dangle at the end...they were both rippin'. Thanks for another great vid.

[@shaneeickmeier6213]

Love the video, especially with my beautiful Yamaha being used for demonstration purposes. 😁👍🏻 Here’s 🙏🏻 for all the snow.

[@bradbraun6271]

Awesome knowledge you and jimmy are doing. Keep me entertained and alittle jealous. Have a merry Christmas and new years.

[@rayharris5097]

Great how too on the secondary. No skidoo in my fleet and likely never will be, but I've got a couple buddies that are gluttons for punishment lol. I'll be ready to help out when theirs are due for rollers... Nice one!

[@prestonbear8981]

Excellent video, very detailed and the drobe footage will be great! I'm wondering Pete if you could do a video on greasing the etec pto and mag crankshaft bearings next? It's a bit of a job and that isoflex grease ain't cheap!

[@ryans6014]

Almost jad to watch yhe video again.....no beer break?? Lol. Jere in Minnesota no snow yet. Fingers crossed though as always keep on keeping on

[@davidpickens3117]

As always, Pete your videos are always entertaining

[@coffeestocks3571]

Great Stuff Boys! Well Done

[@faykos9267]

Good video. Common issue, I have had to replace the rollers on my Skidoo’s. It is possible to replace the rollers without pulling the bearing and splitting the clutch. It is tight but there’s enough room to get the rollers in.

[@craigwhitehouse9573]

Nice one , good to know I own a ski doo🍻

[@ashleyfuller1333]

I can't wait for you to take a look at my sled. I know it will be in good hands that's for sure.

[@michaelhaueisen513]

Great job and very educational. Thanks

[@ronnielamb5958]

Love your content bro please keep it up my dudes

[@tomchalette1509]

What a pain in the ass than his clutches. I'd rather do 30 of the old clutches. Then even five of those. Definitely after that beer time lol. 🇨🇦

[@michaelyarmie4858]

Here in Winnipeg it's -20⁰C. The maintainer just went by and filled my sidewalk that goes across the boulevard to the street with about 2½' of snow. Not a '' nice one '' lol. Ride safe, Dudes and Dudette..

[@GYPSY400]

My secondary is off my sled right now to install the new updated Skidoo rollers as preventive maintenance. It doesn't take too much time to get the secondary off.. And you dont have to pull the bearing off to change the rollers.

[@jeremymullen5378]

Hell ya. Nice work guys. Owners odd to be happy with two fresh rippers cheers 🍻 👊

[@danagibbons9643]

Nice one Pete 👍

[@davedemo8229]

if your easy going into reverse they last a little longer. did mine on a 2015 600 mxz but I don't remember removing the bearing. are the new ones different?

[@GYPSY400]

You don't have to remove the bearing if it's still good.

[@oldjarhead386]

Replace those smooth torx bit bolts on the back side of the secondary with standard hex head bolts. Then you can get a normal combination wrench on them without having to take that jackshaft out. I recently put a full clutch kit spring and helix without having to pull the entire jackshaft.

[@haydenrichardp3712]

Pull the Jack shaft to service the driven clutch ? Crazy engineering !

[@GYPSY400]

I just did mine, took maybe 30-40 minutes to get the hood exhaust and clutch off.

[@chadpeterson-rf8yd]

Great video buddy

[@berttracy90]

Having the belt deflection adjusted properly and having proper track tension. Goes a long ways with rollers breaking. along with not being a bonehead when switching from reverse to forward and back. Ive logged well over 10k on 4 or 5 different ski doos with that clutch design and ive never broken a roller. That being said i see people break em all the time. You want a great video on belt deflection dynamo joe has a good how to.

[@KyleKnowles-sh6vi]

I like watching your videos

[@CurtSchrock]

Ya seems like the old school way isn’t always inferior 🤗

[@tboystoys5682]

I have a 2017 renegade 850X and had to take my secondary to the dealership to change my rollers because I couldn’t get the pins out but I had them change the bearing to. There a pain in the ass and the rollers break a lot more often than you think until you upgrade them

[@Swampkiller1Tv]

New video ……Nice One 🎉🍺🍻

[@Georgebd2]

Happened to me on mine I put the heavy duty ones in no more troubles!

[@xboxgamer6630]

Nice one bud 🍺🍺

[@devonjames9584]

I got a problem with my 700 xc edge she over heating on me yesterday while getting off the lake hopefully I can figure it out!

[@kevinbushey1879]

I love the video can’t wait till you start drag racing when you get some snow. What Mackinski up to .I don’t think I spelled it right 😂😂😂😂. Say hi to your beautiful girlfriend for me. I just closed my auto body shop up and now I’m retired so I have time to watch your videos. My shop was like your every one can over to hang out.❤

[@devonjames9584]

Pete do u have any cooling issue videos on the older liquid cooled sleds probably 2001 to 2002 Polaris sleds?

[@CULT539]

They’re bad for water pumps.

[@devonjames9584]

​@@CULT539thanks for the info anything helps!

[@jeffpine3036]

there is a aftermarket kit that solves this engineering ridiculous design. solves pete's problem of removing entire shaft. team or rapid reaction 2 roller design seem to always bind vs the older 3 helix design. nice video pete cheers

[@MattGuard-s5u]

I know 2 guys recently having seconddary clutch problems. Must be pretty common problem

[@chestermcgillicuddy4368]

Pimento! hahahaha Hilarious!

[@DaveMasse-e6g]

Hey Pete, Check out Thunder Products Clutching out of my home town Cedarville mi in the UP . They sell replacement rollers for the ski doo clutch , they are far superior to the stock ceramic ones. And they are cheaper than stock. I know of several people that have used them, and I am about to change mine out on my 900r. Thanks for the video on how to do it, will be very helpful in the swap . Perfect timing!! You and Jim rock!!!!!! ,

[@mikecallan8346]

Change the helix bolts to hex bolts. Use the circlip roller bolts if you can. Buy the qrs helix tool. Buy the good rollers.

[@haydenrichardp3712]

After watching this video there is no chance of buying a Ski Doo. Totally ridiculous for this to be that complicated. No wonder prices are so high.

[@oldjarhead386]

He made a bigger deal out of it than it really is. I broke my rollers and the first time I made the repair it didn’t take much time at all.

[@MattGuard-s5u]

A new skidoo at least. I love Yamaha triples but I respect the late 90s and early 2000 skidoo mxz . there good sleds

[@oldjarhead386]

@@MattGuard-s5u I have a new Doo, An Apex and an RX-1. None of them are perfect and all have inherent issues. Some of those issues are easily addressed and never worried about a second time. Rollers are one of them. Use hardened rollers and never need to do it again. My older Yamahas have plenty of well known design issues as well.

[@CULT539]

What ARE you going to buy? I’m guessing nothing. Don’t have nothing but sore thumbs on the Obama phone.

[@MattGuard-s5u]

@@oldjarhead386 just ment there easier to work on and 20 to 30 years old with minimal problems unless you beat the snot out of them. Personally I like the older sleds better. Its all an opinion. Not saying I'm right. Just my preference

[@rondierckens6618]

If you don't mind ..what year of skidoo an how many km?

[@berttracy90]

This design although has varied slightly but the roller design dates back to 2008. They just updated the material the rollers are made out of. It's not a km issue. They can break with 1 mile on em. Ive seen em go 7k without breaking

[@72mmALKYDRAGGIN]

162nd 👍 Comment love gents Frm CHICAGO

[@chrisgaudin6395]

Let's go on lunch break even

[@Georgebd2]

What are the skidoo guys has a trick to get in them in without removing everything

[@FridayHavioyak]

I got a 600r etec Renegade just put new pto injector n wih buds on with computer but won't start yet maybe need new ecm? It's hard to get help iin a small community love watching your show

[@otahu26]

AN JUST like that. I am Glad I Don't own a SKI DOO. Couldn't work on that on the side of the trail and get you home. Deff Would need a tow job.

[@GYPSY400]

My buddy blew his and drove it home.. it wasn't pleasant, but he made it.

[@bigjay6743]

Hey Pete I live about a 1/2 hour away from you. Just wondering do we even get winter anymore. I haven't even fired my sled in 2 years. I think in the last 5 years I've only been on maybe 6 or 7 rides. It's getting depressing And I hate trailering.

[@KyleKnowles-sh6vi]

I have a 1991 Arctic cat cougar 440 looking for a primary clutch

[@ericm1430]

Geez there is a ton of corrosion on jimmies 850? Trailer that thing in the salt spray or what?

[@DaleTerry]

Think snow guys!

[@Swampkiller1Tv]

I never realize how big it was 😅 u know ur vise 😅😂

[@TaylorGalarneau]

Why would you not put hitorque rollers in it..they are made of fiber and will last way longer, you are gonna be replacing them again soon

[@rickleclerc4964]

I'll stick with my arctic cat 🐈

[@davidanderson1763]

You're looking like us in Northern Wisconsin. No snow. I'm worried about this season being a repeat like last yr also

[@jeremeysmith5661]

Did anyone hear about artic cat

[@DavidNielson-m7n]

Let the engineers manufacturers work on them once then nothing twice maybe but I kind of doubt it two bad that Yamaha went out of the snowmobile business Jose hasn't reliable sleds

[@MichaelBilodeau-v9i]

I hate to see the grass around your shop!!!! That means we don't stand a chance here in northern Maine!!!

[@cichlidbabys4841]

NO BEER BREAK WHATS GOING ON

[@calcobb442]

Pooh-Doo is right. Never liked them. Polaris guy.

[@haydenrichardp3712]

New technology is not good technology !

[@patyagecic3075]

What a pain in the azz maintaining that driven clutch, you can keep that piece of crap.

[@johnskidmore9020]

omg don't put it in thr wrong hole , you will neaver hear the end of it

[@timseles3044]

What I found very weird was. You were stroking that skidooshaft one too many times😅

[@thomashanke6750]

They make it that way so the regular guy can't work on them.

[@PolarisEricson]

Just need some tools. Then from there it's just plugs and fuel filter every season