Skirting 120 english

[@mikemontagne2703]

As suggestion if I may, when one is trimming the inside corner's 90 degree(at approx.1:55 sec in & again at 4:38 in to video), insert a flat scrapper,(That one has modified by cutting a 90 angled point, or just use a small, thin brick layer's trowel) flush to floor, beneath the skirting, below the razor's cut, so as not to damage the flooring surface below :) .

[@ThePixilator]

Thank You! I've been watching several of these tutorials and yelling at my TV because none of these tubers have given any thought to the flooring as they cut! Was driving me crazy 😄

[@paulmiller6277]

​@@ThePixilator you will find a skilled flooring installer can cut material with a sharp knife without marking material below

[@aqwaaqwa7819]

Why the unlike?.. this is great!

[@bodasencantoxsiempre]

❤❤❤ awesome thank you so much for your time to show us, can I ask what type of Glue you used?

[@Fishingtuts]

Outside bottom corner lays flat on the floor, best ive seen

[@wicopanthers]

Ummmm why we not using cove base again 😑

[@matthewnicholas6365]

Would this work direct to a brick wall and unfinished concrete floor? Trying to make my garage cleaner so painted the brick down to to the bottom row and will put rubber floor tiles down

[@eddypetch]

Then it depends on the adhesive you use. Spend some time searching and you will find one.

[@chrissheafer]

Nice pencil marks you left there.

[@MaxwellFlooringau]

comes of with a wet rag

[@AliS-ec2tk]

The people complaining on here in the comment section, 'oh I could do this quicker, this method is long etc' are basically cowboys who rush the job, and looks awful in the end.

[@chrissheafer]

Except all of the manufactures recommend cove base glue not contact cement and they do not recommend you smashing the lip to the floor. It would be great if people like you who are willing to look like your real smart and bash people who actually install according to manufacture recommendations which validates the warranty btw would just look it up instead of just commenting like an uneducated MORON.

[@JMorris216]

all that extra work and you didnt even get that inside corner tight.

[@bigd211069]

That inside corner would fail inspection at the top.

[@OtherDalfite]

That's what I was thinking. Just inset a dab of caulking and smooth out? Looks impossible to get it perfectly tight

[@paulfisher7911]

well iv never seen it fitted like that .i have to mitre every corner on site as walls are aways shocking

[@Womble1978]

What was the device called that you used to hold the pencil ?

[@Maxid1]

Pencil holder...

[@reysinclair4258]

@@Maxid1 lol

[@LuisGutierrez-ks2uh]

Very nice

[@Maxid1]

0:22 that height gauge marker looking thing is called a height gauge marker..

[@reysinclair4258]

no were to be found, ill like to buy it

[@Maxid1]

@@reysinclair4258 If you google height gauge marker you will find dozens of them.

[@GaryGoRound]

this method would take way to much time...and it would only work on perfect walls...9x out of 10 I am working with walls that are old, have holes in them, beat up, etc...the drywall guys never ever mud and sand down to the floor. They say it's the flooring installer's problem to make the base on crappy walls look good

[@carlhurley6134]

No way’s

[@jonvon2044]

Sounds like hack behavior to me 😂

[@J1SMOKES]

What adhesive is he using ?

[@n2itsion]

Looks like contact cement

[@selectflooring]

where do you get the scribe for marking the wall

[@krystinthaboss7816]

Ian Hadfield right, that's a nice little tool.

[@fintanduffy60]

If it's a one-off job just cut a block of wood. If you are a pro buy the tool.

[@jrhhandle]

did you ever find out the name of that scribe tool ? I cant find it online.

[@markallen8097]

Janser do them, called a wall scriber for cove

[@northwestgardener5076]

If I ever took this long to install base i would be fired for incompetence and milking the shit out of the clock. Oh nice pencil mark above the base have fun selling that to the GC who just watched you spend half a day doing 1 room of base. Oh and good luck on the piss test they will be sending you to tomorow.

[@eoaks5296]

This would probably be a great video with out the music

[@erbrooks]

Can this be painted?

[@bakhtiaressa]

Thanks good job, what is that hand tool Called that have you been used it for please ? Chisel ??

[@jasonhamilton9200]

Carpet stairtool

[@jerrymoralez5602]

what adhesive is using it?? I tried but it doesn't work

[@MaxwellFlooringau]

contact

[@clintonlowen]

You just made this 10 times harder. 😢

[@chesterc.cabrera1560]

El que ha trabajado con este tipo de material sabe que después después instalado tiende a encoger, entre 0.5 cm. ¿Alguien Sabe por que pasa esto?

[@eddypetch]

If heat is used the material will shrink when it cools.

[@mikesacco8457]

I have always tan caulk at floor and wall. Base has a gap at bottom so this way you can try to prevent water damage. And don’t we all wish we had perfect walls. Drywall guys. Screw it let the finish guy deal with it

[@wesleywarren5992]

Perfectly and professionally executed. This is indeed the way vinyl base cove is always to be installed. Any other way is pure laziness and shortcuts to product failure and poor looking workmanship..

[@Honkahonky]

Try doing those corners with roppe 700 series or jonhsonite and have good luck without grooving then.

[@ericfisk7206]

agreed, why not at least score the back at inside corners to get a clean 90 deg corner. versus a rounded corner?

[@chrissheafer]

BS. This is not how to install cove base and no, the bottom is not supposed to complete lay flat on the floor. Also, after 45 years, I rarely see walls this good. Doing this method would look like crap in most applications. Here are the facts. A good installer knows all the methods of installing cove base and uses the application that best fits the job and circumstances. Besides that, show me a single cove base manufacturer that recommends using contact cement to install their product! No, they recommend using cove base glue. They also don't recommend you push the cove base down so it fits flat on the floor. The flare they manufacture is the flare it's supposed to have what it's installed. The only reason why a person would install it like this video is if you are ignorant and don't care.

[@xLegionnair]

I hope in 6 yrs youve aged some

[@jezeus5493]

That is way to long to do a corner.

[@ollu5586]

Great, Tanks

[@kylegrant1881]

The fumes from that much contact cement will kill you real quick. Just cut the inside and outside corners completely and put one over the other. I use zero contact cement and have seen old outside corners from 5 years ago still perfect where contact would fall off. DON'T USE CONTACT CEMENT THE FUMES ARE BAD!

[@punchogunter2362]

This method takes too much time! For instance im working on a school 🏫 or hospital 🏥 and I only have a few days to complete the whole first floor🤔🤷🏽‍♂️😔🏋️‍♂️

[@ProgressProfilesTV]

Dear user, this video shows you step by step installation to get high installation quality and greater understanding of the method. The speed of installation depends on the installer. I invite you to contact one of our technicians to help you with your projects. www.progressprofiles.com/en/contacts

[@danyfilion6024]

1500LF would take him months to finish

[@TheManorBeast]

I can smell that F60 from here. Fumes are lethal. It’s neat to be fair but you can’t take that long on two corners

[@ProgressProfilesTV]

Dear user, this video illustrates the correct installation of the product. We are sorry that many users complain that the installation process is long but the time required for installation is the time to obtain a quality installation.

[@danyfilion6024]

@@ProgressProfilesTV when you have to pay unionized workers $45/h to install VB they better get some serious LF's done just to break even

[@jonvon2044]

Where do you live that they pay that?

[@thisbetterman]

Wonderful video. Thank you. Horrendous music.

[@mrscloverfields294]

Dont bother saying what ANY of those tools are called. "Pencil in vice measurer thing" Type of epoxy? Nope. Details? Nope. Hints? Nope.

[@dougk06245]

i'm thinking contact cement and a stair tool and i'm not sure about the pencil thing

[@reysinclair4258]

lol

[@charlesgunter2478]

Too much time spent! Cut the back of the corners and keep going!

[@jesuszavala1155]

@Charles Gunter right! fuck yea I’d be paying rent at the places if you catch me doing that shit😂

[@j.p.sharma3223]

J. P. Sharma

[@kfej5380]

Your inside corner is all fucked up. He had to learn how to scribe or do free style. If you want her inside corners tight. Good luck.

[@rolandsnyder9703]

This seems way overkill.. if I took this long to do one wall, I'd do my boss the favor and fire myself

[@maurogiaretta6385]

What do you suggest then? This video is a demonstration...

[@jaydee9005]

lol this is the worst possible way to install wall base especially without taking off the backing of inside and outside corners ull take 4hrs doing three lengths xD

[@Meatpopsicle2050]

So much wrong here

[@javiermeneses1272]

This people work hourly too much work. And time consuming....

[@northwestgardener5076]

No joke I would starve working that slow for piece work,,, especially when you get a call back to come erase the pencil marks above the base on the outside corner.

[@ekremtunca2783]

Wf you can’t work like that how much are you charging for this baseboard you can’t make money and if they wanna changing how they take off with contact cement you guys crazy mapei eco 575 baseboard glue nice for baseboard you have to try 😂😂😂

[@williamdiedwardo1386]

Slow

[@LeeJF1]

Video 👍 Music 👎

[@billymacktexasdetective5827]

Great, now I've got visible pencil marks everywhere...

[@xLegionnair]

What a terrible tutorial. Totally wrong beginning to end

[@ProgressProfilesTV]

For many users the tutorial is very clear and expresses the correct installation of the product. Please contact our technical service for more product information.