This video will show you how to perform Smart Pressure TX Calibration using HART configurator, So Watch this Video and Please Like Share and Subscribe.
Пікірлер: 53
@waqasaslam83793 жыл бұрын
you have good teaching skills dear. Allah aap ko ajar dy
Sir connection kaise kiye hart aur multimiter transmitter ka wo video banayea
@mohammedk11273 жыл бұрын
by using this protocol how can i set the jump step value in pt i want to make it very sensitive of pressure ( less the value or decrease it )
@industrialautomationandele63243 жыл бұрын
Sensitivity depends on TX range if u want more sensitive then select max TX range near to ur operating range. For example if ur operating/calibration range is 0~10 kg then select TX which max range should be 12~15 kg/cm2
@sanaurrasheed4 жыл бұрын
Plz make more videos
@dasarisurendrababu68243 жыл бұрын
Sir please make vedio about pressure switch calibration
@sawaulhaque63883 жыл бұрын
Please make video about how to configure from sensor1 to sensor2 in rosemount 3144P by using hart 475
@sushilgharat2264 Жыл бұрын
Hello sir, We are using Rosemount as well as Yokogawa pressure transmitter. In Rosemount PT we can calibrate PT with the help of Zero and Span push buttons on top without HART, so can we calibrate Yokogawa PT without HART as there is only one zero adjustment screw.. Pls reply..
Hard communicator aur multimeter ka wire conecsion kaise uspe video banayea
@sumeet2912 жыл бұрын
Multimeter series main lagaya howa hai .. I guess parallel main lagna chahiyeh..
@bonojitpaul6432 Жыл бұрын
Sir mujhe eska wiring diagram mil chahia calibration karne ka
@satyendra12742 жыл бұрын
Sir industry me Positive pressure and negative pressure dono measure karte hai to uska unit kya hota hai aur hart comunicater se calibration karte time kon kon se bat ka dhayan rakhana chahiye jaise ham new transmitter installation kar rahe hia pls suggest videos or make videos Pls
Asalaamu alaikum sir aap ki Training Centre kaha hai
@gopalakrishnagopal43565 ай бұрын
Coonection Daigram showme sir
@bonojitpaul6432 Жыл бұрын
SIR MUJHE CALIBRATION KA STEP BY STEP JAN NA HAI PLZ
@sushilgharat22643 жыл бұрын
Hello sir, Mera yokogawa ka Press Tx hai model hai EJA530E Range hai 0 to 5kg/cm² Iska zero to thik hai, 0kg pe 4mA milta hai lekin span 5kg press pe 18.6mA milta hai. Press Tx pe 5kg dikhata hai lekin mA kam aa rahe hai. Span adjust kaha se kar sakte hai.. Yokogawa me sirf 1 hi screw hai aur wo zero adjustment screw hai. Display me button hai wo local parameters set ke liye hai.. Can you please clear.. Thanks..
@industrialautomationandele63243 жыл бұрын
Is ki current ouput calibrate ho ge. normally ye D/A calibration ke name se hoti ha
@asirasperislamicruleswitho30222 жыл бұрын
D/A , do the D.A trim and also , EJA530E mien manually zero aur span ik he screw say adjust hoskta ha.
@bhupathiharsha42233 жыл бұрын
Please show me connection sir
@UmeshSingh-rg1qs2 жыл бұрын
I need your help... one transmitter range 0~600 but apply mA through HART display value here 4 mA=0 25%=152 50%=305 75%=457 100%=610 Plz guide me..
@asirasperislamicruleswitho30222 жыл бұрын
do the zero trim ,or D.A Trim. also check the acceptable error in data sheet.
@HuroHuroa4 ай бұрын
Hot comedy Bangla
@mdanishsheikh11773 жыл бұрын
Kuchh question hai jo samjha me nhi arha hai
@mahendrapahadia5518 Жыл бұрын
Voice????
@mdanishsheikh11773 жыл бұрын
Sir AP ka number chaheya
@Firesafetyworks3 ай бұрын
Not the helpfull this video, some points are missing