Ever tried to solder and you burn out your Hakko or clone soldering iron, these clone tips are made from dubious materials, I cannot believe they are not Copper. #Hakko #soldering #fakes
Пікірлер: 21
@dan3a2 ай бұрын
I remember using knockoff tips a long time ago... they were just erroding away, awful stuff. Was afraid the expensive tips on my pinecil wouldn't last either and would just disappear after a few months, but here it is 2 years later and all tips still look pristine.
@DetectorMods2 ай бұрын
We are caught with eroding tips and tips that do not transfer heat, I think there is a business opportunity for a start up.
@officermeowmeowfuzzyface44082 ай бұрын
Can confirm. Get quality tips.
@DetectorMods2 ай бұрын
It’s either buy GENUINE Hakko or run the risk of buying crap products.
@jamest.50012 ай бұрын
I have a couple of the soldering Irons, and even the knock off tips seem to been knocked off. The knickoff tips usually blast a while, the replacement tips i got. The tip of the tip eroded away. With it looking like it entered. The atmosphere at 10x escape velocity about 20%, of the 3-4 mm remaining. Almost impossible to use, I only use it to solder wires together, replace it for anything else,. Can't believe its sc crappy! Where does the metal go?
@DetectorMods2 ай бұрын
The metal is dissolved by flux and molten solder and is transferred to the solder connection, I found all the tips are picked up by a magnet, so they are iron.
@edwardneuman60612 ай бұрын
It;s just not Hakko. I bought additional tips for my TS-100, but they were 3rd party. The temperture on them tends to jump around alot compared to the ones that came with it.
@G-Hawks2 ай бұрын
Yeah i had the same problem with tips for my hakko fx-951, all fake crap, unless i order from RS.
@drbobsnightmare25212 ай бұрын
I thought he was Larry Bird. 😂
@donwright34272 ай бұрын
I made my owm screw in tip from a chunck of nickle .hard stuff to machine. Thought it would be good but didnt transfer the heat very well.
@DetectorMods2 ай бұрын
I want to make my own out of pure copper and plate the tip part.
@danielflinn35712 ай бұрын
Thanks for sharing
@DetectorMods2 ай бұрын
Thanks for watching!
@marsbabe002 ай бұрын
Looks like stainless. Try a magnet test.
@j.f.christ84212 ай бұрын
Stainless is almost the same weight as copper. Unless they skimp om that as well. Probably 303 if it is.
@darrenmurphy62512 ай бұрын
that explanes alot ive been cranking up the temp for years now thinking solder isnt as good as it used to be ! love that soldering tip thermocouple, where can i get one and can i use a k type meter i already have?
@DetectorMods2 ай бұрын
Aliexpress for $2 most are compatible with common multimeters.
@scotshabalam24322 ай бұрын
Why didn't you shop direct from Hakko? Was it too expensive? If the Hakko store is "too expensive" then you can't really complain that you bought the cheaper alternative from China.
@DetectorMods2 ай бұрын
10 tips from China $10 from Hakko $100
@scotshabalam24322 ай бұрын
@@DetectorMods If you can get a molecularly bonded solder joint without cooking the part or the board then it's fine for you. I would tell most people to stack the deck in their favor when soldering, though.