Solidworks tutorial | sketch Worm gear Animation in Solidworks

[@wongcinsheng3937]

In order for the worm gear (small one) and worm wheel (big one) to be mesh. The pitch must be equal for both. The diameter of the worm wheel is also important. It can be calculated using this formula >> (Diameter = (pitch x number of teeth)/pi). If the pitch is 6 and the teeth is 60, the diameter will be 114.59mm. If the number of teeth is 60, the gear ratio would be 1: 60. Means that when worm gear rotate one rev, the worm wheel will move by one gear. For 30 teeth, the gear ratio would be 1: 30. Hope this help :)

[@matheus.alcantara]

Your content is great! And the videos are very helpful. Now I go to class, sit in front of the sreen, put my headphones on and draw whatever the professor tells us to. Thanks for sharing your knowledge

[@unclesam6764]

GOD bless you! i acknowledge u as my teacher!

[@emiellambrecht3663]

When you start to design a shaft (or any revolved body), you should start with a construction line as centerline and then add diameters instead of radii. Move the cursor from the line to be dimensioned to the centerline and move a bit across the centerline. The dimension changes from radius to diameter. The gearmate can be reversed to correct the animation.

[@KulbirAhluwalia]

Thanks a lot for the step by step explanation sir! Kindly make a video on how to calculate the dimensions of these gears when gear specifications are given

[@vuongquoc1981]

i have a question: when u draw the thread for the shaft in 5:50, why don't u just draw a circle at 1 end and then draw the helix to the other end and then sweep boss/base. Instead of that, u start drawing from the middle and then u have to draw 2 helix to 2 ends?

[@muhammadmuzamil3248]

Thanks for the tutorial. It would be great if you could show us how do you get the dimension based on the formula.

[@MrMytubevidmaker]

Gear ratio is 44:1. The number of teeth on the worm wheel is 44 and the worm acts as a single tooth gear, so the ratio is 44:1. Cheers!

[@CADCAMTUTORIALBYMAHTABALAM]

it's not real ration just imaginary ratio to show the way of gear ratio plotting,

[@JibzCastor]

It's hard to do this video if youdon't show the data/calculation on how to make a worm gear... The data given to me by my prof is: - RPM Driver 1840 - RPM Driven 240 - Shaft Angle - 90 And I will make a worm gear? :( please help

[@SUPERPUFMAN]

I have the same problem, but instead RPM I got HP and reduction ratio, did you get good grade?

[@KulbirAhluwalia]

So the ratio in Gear Mate would be 44:1 mm right?

[@jaatsaab3020]

good video

[@sk32md]

The proper gear ratio for the motion study is 83mm/gear x 2mm/shaft. I think I made made my threads on the opposite end so I had to un-check the reverse box. And great videos BTW!!!!!

[@CADCAMTUTORIALBYMAHTABALAM]

thanks

[@shastraniti6883]

thanks for helping us in learning solidworks may god bless you fulfillment of your dreams

[@CADCAMTUTORIALBYMAHTABALAM]

Thanks.

[@jeffhi-lander5038]

I always go back to this super tutorial. Very concise. Very accurate. 10/10. Thank you very much.

[@abdulkareemalmotairi3488]

You are an excellent engineer😍👌🏻 Greetings to you

[@diegofernandesdonascimento7729]

You've been doing a great job here on KZbin...Keep it up!!

[@CADCAMTUTORIALBYMAHTABALAM]

Thanks.

[@glendcruz6456]

Thanks for your tutorial. Unfortunately in Inventor I do not have the spiral tool, however I managed to get it done and it runs well.Thank you .

[@ErdemOrs23]

Nice work, thank you for the effort.

[@cameronross-day9197]

cool job dude very helpful

[@enzonicita2000]

Incredible

[@monsterjesse]

excellent, thank you for the effort.

[@Truth_teller10]

Keep doing ..your efforts helped alot

[@jansonbiswas8486]

great sir

[@abdulrouf8564]

Nice Job

[@fergianetti1579]

Bro your videos are very nice, thanks for all the time spent on making them!! Just one detail man please try to avoid breathing on the mic haha it's like you're breathing right on our ears

[@MohammedSiddig-w2s]

he is nice breathing love it

[@muhammadafifhidayat2566]

did a mate between origin point and circular gear , made a gear rotate on origin point?

[@KH-pf7uh]

👍🏻Good

[@gennadygerun7329]

Very informative, thx. Unfortunately, absence of the geometry calculations makes some questionable moments unclear.

[@bstevermer9293]

Awsome!! Thanks for up loading!!

[@guinglamesh]

how do you did the calculation of this parts

[@we9092]

I have the same question

[@AmitPatel-ty9nx]

Good video for making toys, no calculations, no formulas, all dimensions comes from ........

[@achournourhen6635]

great tutorial, pls how can i check if it is irreversible system

[@LucasFSPimenta]

Nice work man. I need to make something like this with more worms. Something like an automatic barbecue station. I've added one more screw to the axis and i'm trying to atatch one more gear on in the assembly but i just can't make it spin like it should. What would be diferent?

[@jjwil1508]

Tanks you for this tutorial

[@jasoneyes01]

Thank You teacher!

[@CADCAMTUTORIALBYMAHTABALAM]

Thanks.

[@rizkiputraprastio7553]

It's an excellent tutorial. But, I think the gear is spinning in the wrong direction

[@vishalnenual3119]

Take gear ratio 44 for worm wheel and 1 for worm shaft in gear mate and Take distance 38.5 mm in mate between worm shaft's face and right plane. Do this and Ur gear's teeth will not overlap each other.

[@EnricoDellaVolpeTechnology]

Amazing

[@Hayness_Morata]

Hi, how did u share the screen. Any tutorial?

[@chappyaugusto]

Great video: I wonder if you can teach to do machines if it is so I will be at top of the list , whit proper remuneration for you of course. let me know. tank you.

[@rishabhswarnkar8388]

Is this possible to draw directly from the tool library?

[@kanchonful]

in 6:26 times you make helix again? why did you make two times helix? instead, why did you not make one-times helix?

[@_blank_3737]

Just do it dude

[@catkeys6911]

Great video, and I appreciate your effort, but if you are trying to teach this subject, you really should have the correct gear ratio of 44 to 1

[@PavanKalyan-ig2bp]

No it's not correct, because 1st selection is worm and it has more gear teeth than shaft. If u give that ratio (44:1) then worm will rotate 44 times for 1 rotation of shaft

[@josebordes8829]

Thanks for the tutorial ;)

[@CADCAMTUTORIALBYMAHTABALAM]

welcome.

[@Netsroht72]

Hm, i think you made a mistake. At 13:00 you choose counterclockwise, at 17:09, for the 2. Sweepcut, clockwise. Thats wrong in my opinion. You can make that sweep in 1 cut, choose the Startpoint wisely.

[@zahramaleksabet7205]

that was very useful thank you so much :)

[@surveyengineer2372]

Thanks for the tutorial. i draw in F360 and 3D printed. it didnt work. i supply motion by using a motor(14 000 RPM). Do you think this motor not suitable? too fast maybe?

[@s.s.torgal1324]

Nice tutorial thanks

[@gilbertofructos3955]

👏👏👏

[@3ddesign452]

nice

[@CADCAMTUTORIALBYMAHTABALAM]

thanks,

[@tariqhussain3371]

can u make a video on how to make a casement windown using a single arm operator crank

[@ashokkumar-kc9jb]

can you please explain me the start angle i cudnt understand abt it is it the lead angle ??? or what pls reply soon

[@abderrahimfiguigui8079]

please witch is your vga cards?

[@MrWinterblade]

Very useful

[@CADCAMTUTORIALBYMAHTABALAM]

Thanks, please share our videos which is help us to do more and more in Solidworks.

[@MrWinterblade]

Very useful, just a question: how can I prevent the gears to slide into themselves while rotating? they cross each other. Thank you for the help

[@CADCAMTUTORIALBYMAHTABALAM]

actually use contact relation during motion analysis, check my new video in that you will see how to avoid interference between gear. kzbin.info/www/bejne/iHrMiZuYmdGorrM

[@GaneshHosur97]

the notch at the center of the gear is rotating in the counter-clockwise direction while the periphery of it (the gear) is rotating in the CW direction..how could it be? Nevertheless, great video!

[@zicozizo9558]

That's a good question!!

[@vikasmange383]

Yes i also observed.

[@emiellambrecht3663]

In the gear mate, you should select the opposite direction

[@amanchander7837]

How did you know that the number of threads (at 18.34) on the wheel gear? I think that the number of thread impression on the wheel gear depends on the pitch of the screw. Please explain. But the tutorials are good. Thank you!!

[@catkeys6911]

OK, why did you start your worm gear in the middle so that you had to do 2 sweeps, instead of starting at one end and only needing 1 sweep?

[@catkeys6911]

Oh, and also, the second part is the GEAR, not the worm. The worm was the 1st part you made.

[@jonassalazar5467]

Is amazing, i loved it but why do you keep using solidworks 2014 instead of 2016?

[@VijayKumarVijayKumar-oc5qf]

Bakwas karate hai yar

[@mahfuzulhasan1366]

Your video is fine. But I don't understand why did you make the worm wheel as a driving gear? Is it practical?

[@happybreadfruit3530]

Bcs it must be... How you would push worm gear with normal gear ?

[@vietlinhnguyen6321]

what a outstanding video! But i think you probably should change your mic, the sound was too bad, too much breath

[@rajen2954]

In animation the motor is connection is impractical. The gear would never move. The motor has be connected to the shaft and not the gear.

[@samosiriano4296]

thank you :)

[@leoedison3879]

Hii ..How can I increase the number of teeth in warm wheel???

[@turboblain3281]

nice，thank you！

[@CADCAMTUTORIALBYMAHTABALAM]

thanks

[@matthewschmidt106]

Whenever I spin the gear the worm moves with it what did I do wrong?

[@emiellambrecht3663]

The worm is not mated correctly. The only freedom should be rotational.

[@thronex4741]

the wheel and the worm is literally cutting each other man

[@مرتضیکشاورز-ت7و]

🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻❤❤

[@j.n.d.p.5891]

thanks brother

[@antunvojnic879]

Gospodine, Imam utisak da niste mašinske struke. Možda poznajete korišćenje SW programa. Jedino što se tu može korisno naučiti od Vašeg pokazanog znanja je modul Animacije. Na modeliranju mašinskih delova i sklopova morate još poraditi kako bi čitaoci mogli korisno i korektno naučiti.

[@TanvirAhmed-sj1hp]

dear sir, Pl, tell me where is flip mat icon

[@CADCAMTUTORIALBYMAHTABALAM]

once you select any mate a small window will popup there you will find flip option or at the end of standard mate option you will find aligned(flip) & anti aligned option,

[@anwarzeb7094]

Both the teeth are not exactly mash you need to create a mate to perfectly mash it. Then suppress this mate ensure the rotation then create a mechanical mate

[@HKhiat]

Bonjour.J’ai constate un décalage des engrenages après une certain de rotation de la vis, ce n’est pas normal. Peut-être le contrainte et male règle, est ce que vous pouvez le remplacer par contact. Je m’excuse pour mes commentaires et fautes d’expressions. Merci.

[@CADCAMTUTORIALBYMAHTABALAM]

its true, its not perfect mate we need to correct it,

[@Snehesha2416]

thank you so much

[@CADCAMTUTORIALBYMAHTABALAM]

Thanks.i hope you enjoyed.

[@DudyOne]

Nice job, but I was brought up with the worm as the driver and the worm gear as the rider! You named the first part as the worm gear, not the worm!

[@manuelmejia-h4o]

I will like to see one that turn left and raight

[@sunildodke4981]

Gear ratio is depend upon no. of teeth on worm wheel divided by no. of starts

[@CADCAMTUTORIALBYMAHTABALAM]

true, the gear ratio is not correct,

[@billeawang8951]

Why do we need half clockwise and half counter clockwise

[@FarhanAli-sj7pq]

Worm gear cant rotate the worm, one of the most important property of worm gear

[@vaghelabhavesh4255]

how i will get 2d drawing for this tutorial???

[@JulianVerdouw]

If anyone sees this< can someone help me with how to make a worm and a rack motion? I can't figure out how to connect them to each other. They keep going through each other

[@thronex4741]

why 44 threads on the wheel??

[@Abdurrahimmm]

thanks

[@yossydhimasirawan587]

link for download application solidworks please !!

[@esedesedov1140]

ela ok

[@trollz0r579]

Hello Mr. CAD CAM TUTORIAL Could you pass me a channel that has a tutorial teaching the tools all in detail?

[@CADCAMTUTORIALBYMAHTABALAM]

you can learn basics tools of solidworks in my channel check playlist.

[@trollz0r579]

Link from the videos?; my skype Unless you add me: ramligasf

[@suhasgorthi7466]

This method is difficult. Please suggest an easy method.

[@CADCAMTUTORIALBYMAHTABALAM]

Ok in future i will try some easiest way, thanks,

[@tarankalsi2128]

I am not able to convert entity 12 : 47

[@sumedha706]

Sir can you please share the parts

[@satyanarayan2700]

You need to motor the spiral wheel not the gear please see other are ok

[@harshserasiya8341]

Everything is good but you just need to change your mic it’s very annoying

[@김원종-j4p]

good video, but gear ratio wrong

[@CADCAMTUTORIALBYMAHTABALAM]

true the gear ratio is wrong, just to show how to make the gear relation in Solidworks,

[@АКИФЛА312]

кончаю от ваших видео

[@vicomedia1]

high reflective surface is hard to see

[@creatures96]

Man the gear ratio is wrong. it should be 1: number of teeth of the wheel

[@telwat]

direction inversed

[@CADCAMTUTORIALBYMAHTABALAM]

Actually i forget, Thanks,

[@LuisGutierrezGomez]

Gear turns in the wrong direction!

[@Alzexza]

Doing rather than teaching, unfortunately... " do 1.3mm".... why not "5.6 MM",,, come on guys your better than this

[@yugautogeirej3099]

sir Hindi me video banao

[@berquijano5608]

Not realistic model...

[@CADCAMTUTORIALBYMAHTABALAM]

true its not realistic model

[@tonyhill8300]

totally pointless unless you use a standard tooth profile and include your workings for every dimension .

[@ManjitSingh-vw2qy]

totally wrong tutorial

[@stema84]

that the gear moves in the opposite direction at the end of the video? :D

[@sumitmandlik5367]

Manjit Singh I was going to comment same.. And teeth were colliding.. He chose wrong faces for gear mate..

[@hafizmuhammadwaqasbadar6024]

the most important thing is in worm gear and worm wheel system wheel can never rotate worm gear.. hahaha but solid works can do that.

[@rcarulasan]

driven and driven gear was wrongly configure. worm gear will drive the spur gear. but still good job, just need to review about the mechanism.

[@valdircarlos6769]

0K.