CZ 75 CZ Recommended Cleaning

[@jojobfast]

Took this to the range for the first time, along with a Glock 19, an Beretta APX. The CZ 75 was the best of the 3 by far. Racking the slide was like slicing butter with a hot knife. My shot group was tight and on target. Recoil was soft and all in all, the CZ 75 was amazing. I have the CZ 75B, not ideal for conceal carry, but definitely an outstanding firearm.

[@3.eyes.open.]

As long as you have a quality gun belt and a comfortable appendix holster it's actually a lot easier than you might imagine

[@Jaybird-oo3ih]

I have the 75B and love it as much as the others I own

[@NaptownSubaru]

Just finished my first time cleaning. Had to rewind a whole bunch but I’m definitely satisfied with how it turned out. Thanks man.

[@chris3383]

I have experienced nothing but joy from owning my CZ's I will never part with them !!!

[@davebowrin7361]

I have a good friend I worked with at the Air And Space Museum with. Our unit would go shooting at a range near Dulles Airport. He was former NYC arson investigator. While the rest of us were shooting our Glocks and and sigs and berettas and 1911's he was happy shooting his CZ75. It was the 1st time I shot it. And I was really happy with the way it shot. And it shot any type of ammo you put through it.

[@ronschramm9163]

I would suggest adding a pair of non-coated nitrile gloves to help keep any lead residue off of your hands. Also, a trick to cleaning the spring is to insert the edge of your cleaning patch into the top side of the spring, so that it runs between the coils, wrap the patch around it and then using a twisting motion, run spring through the patch. You would be surprised how much residue comes off.

[@sootch00]

Thanks for the tip Ron!

[@ronschramm9163]

@@sootch00 Glad to help the community. My wife says I am anal about my firearms, because I wipe and clean them on monthly schedules, even if I haven't put a round through them.

[@jasonb8712]

Very thorough and informative.

[@gunsquawk4443]

Ditto. Works great!

[@richardkluesek4301]

q tips and the industrial ones with long handles for use as applicators for springs, nooks, crevices, and rail slots..

[@worsel2113]

Yet another good video. Thanks. I use a little variation. (1) I use Ballistol, and lots of it. I soak most of it - not the firing pin area, and let it sit for a while. It won't hurt rubber, plastic or wood. In fact, wood loves it. Then I brush, and spray again. Then dry, with an air blaster a little, and wipe with clean cloths. (2) I use a bore snake instead of a brush. (3) I don't use "oil" on the barrel, slide, or other parts that have metal-to-metal contact. I use only grease for that. I like Lubriplate SFL-0. It's non toxic (Ballistol is too). The main difference between grease and oil is that oil "migrates." It will flow anywhere it can. That's good in some places, but not good on the slide. You want something that will stay put, and lubricate until it's lost its usefulness, not until it migrates away. Not all of my shooting buddies agree, but this works great for me, and I am seeing very few signs of wear even after thousands of rounds.

[@sootch00]

Thanks Worsel! I appreciate your sharing your process.

[@Gieszkanne]

Yes grease for barrel, locking lugs and rails makes more sense.

[@shawnbane585]

Czech steel over Austrian plastic any day of the week

[@krazymoney33]

@Maurice Crosby did it work

[@arturraban1738]

Austrian plastic is combat weapon, czech steel is not combat, easy malfunction. 22 parts austria vs. 76 parts czech

[@hoppinggnomethe4154]

​@@arturraban1738 lmao you said that the Czech steel ain't a combat weapon? it's been in combat since 1975

[@3.eyes.open.]

Only real men carry full size steel frame pistols 💪🏴‍☠️

[@3.eyes.open.]

​@@arturraban1738ha lmao the MRBS rate of malfunction with a Glock is a whole hell of a lot less than a CZ 75 buddy and the 1911 man himself the legend Jeff Cooper loved the cz 75 he considered it the best service 9mm weapon ever so pull up ya britches young man and get yourself a CZ

[@hornetbrown]

My (1990) CZ-75 pre-B was my first CZ pistol, owned it for 27years, probably shot 300-400 times since I've had it. Great shooter, tad to heavy for concealed carry but occasionally in the winter (big coat). We used to clean our Berettas this way in the Guard--I apply what I've learned to all my pistols. Plenty of revolvers and autos since then, esp. my P10c and SP-01 Tactical, both awesome shooters.

[@Sloopy40]

I’m very quickly becoming a huge CZ fan!

[@ronstone6677]

Sootch... Bought my CZ75B in 2003 and it has never had a FTF in all those years.. Workhorse of a pistol.. I carried a Browning High Power in Vietnam, and my CZ reminds me of it every time I squeeze the trigger.. It truly is one of the Wonder 9mm of the world and I highly recommend it to anyone considering a purchase... Go Army, Beat Navy !

[@MBZ-Nation]

I can't believe a seasoned veteran like SOOTCH00 doesn't know the first stage of the hammer is the slide hold position to remove the slide pin! Come on man! It's genius on CZ's part! You don't even need to be cautious about lining up the marks on the slide/frame. You just pull the hammer back to the first stage, and then pull the slide back. The lines match up, and you can pull the slide pin out.

[@gregggruse2522]

You should share your information on your website

[@arodrigues2843]

I use a CZ-85 Combat, for IPSC.!!! ( The '85 differs from the' 75, in having ambidextrous controls, adjustable rear sight, and a hammer without the ring)!!! GREAT gun, great balance and handling. I've put thousands of rounds thru it, NEVER ONCE jammed.!!! Love it.!! BTW, I think it actually has EXTERNAL SLIDE rails, and INTERNAL FRAME rails.!!! Allways nice to watch your videos.!!! God bless GOA, Long live the Republic.!!!

[@atlantajunglepythons1744]

Long live Democracy!!

[@SergiusLigurAugustus]

Thank you Sootch I have CZ 75 Sp 01 and i love it!

[@kimsiewers]

The CZ75 B was the first gun I ever owned; it spoiled me for other guns. I clean it similar to this video and use Remoil for lube. The trigger has smoothed out over the years.

[@82luft49]

It's important to change your guide rod spring after 4,000 rounds. The slide will eventually begin to malfunction (mainly not going into battery, dead trigger) causing stress on the gun. It happened to me, so I thought I'd pass it along.

[@pkretschmer]

Danke für den Tipp, werde sie bei meiner CZ 75 SPORT austauschen. Außerdem habe ich mir ein neues 3 Punkt Visier neu aufbauen lassen.

[@krazycisco5029]

I just want to say that I bought my first CZ five days ago, 75B and I went out to shot it yesterday. I love it. Now I'm thinking of getting the SP-01 and the Remi. I hope I can save up fast enough that it'll still be at the store that I go to. Thanks for this video. I cleaned my CZ prior seeing this video and I did somewhat what you did.

[@benjaminmarkson7161]

There is nothing better than a CZ in design, function and finish. I just sold my brand new S&W Shield Plus for a loss, it was defective right out of the box, 12 weeks for warranty repair.

[@gregggruse2522]

I too just parted with a shield plus for a P01 but I still have 2. They’re awesome too.

[@michaelburke3731]

I love my CZ 75 SP-01. It's simple to take apart and clean and it fires with little kick up on recoil. I think it's a great gun for the money.

[@looselatigo]

The CZ75 is an old favorite of mine and I have several as well as Italian, Israeli, and Turkish clones. All work well. One CZ I really like is the CZ40B sadly now discontinued. It started as a collaboration of CZ and Colt on a .40S&W service pistol. Really nice gun.

[@stevenwest2047]

I put a little synthetic gun grease on my slide rails on all my CZ’s. Smooth like butter. CZ’s are an addiction.

[@matthewcooksey5411]

Zero issues with any of the weapons ive chosen. (Cz sp01 being one of them). Couldnt be happier and glad I did my research.

[@traceycroom6036]

Thank you I just purchased my 1st gun the CZ 75 Tactical in Grey & I love this gun! Thanks for showing me clearly how to take it apart & clean it! Thank you 😊

[@spiketheadventurefurry8732]

I just relentlessly got my hands on the SP-01 tactical. Best gun I own.

[@Sheltowee1775]

These are the kind of videos that originally drew me to the channel: how to and practical helpful things.

[@sootch00]

Thanks Johnny! KZbin spoiled a lot of the Gun How To Videos with their new policies but we're working on more.

[@davidpirozzi3984]

Thank you for taking the time to show how to clean it "as instructed by CZ". This video was very informative and I had to rewind quite a few times since I was cleaning my new CZ 75 P-01 while watching you do it.

[@laf43777]

My CZ85B would only shoot flawlessly with certain ammo like Remington 115 grain. In KZbin I found other owners with similar problems. Mostly misfires and the remedy is to change the firing pin. I was able to find an extended firing pin through Numrich. Since then my CZ will cycle every type of 9mm. It’s my favorite pistol. It’s elegant and definitely accurate

[@ronniemw5022]

Magazine maintenance is just as important, thank you for including it! I have a P07 and my 17 rd mag is devoted to carrying my self defense rounds. Every month or so I empty it, disassemble it, let the spring rest for a while, then wipe it down with clp and reassemble. You can keep your gun like new with regular cleaning but if your mag fails what good is your gun?

[@tonydeaton1967]

Modern magazine springs don't typically need a rest.

[@Eupher6]

My CZ75BD is a keeper. I'll use a tiny bit of gun grease on the slide rails - seems to work well and the grease does a great job of trapping residue. Just wipe clean with a dry cloth folded to get in the rail crease. After about 1,000 rounds or so, I'll remove the firing pin and clean out the channel using a dry Q-tip.

[@hvy747]

I keep watching your videos on the CZ75, I just love mine.

[@Jaybird-oo3ih]

The greatest thing about the CZ 75 line of pistols is that the amazingly low prices I find them at the gun shops. I picked up a lightly used PCR for $350 in 2024, I just smiled and paid the man. 😁

[@fixedit8689]

I bought one over 15 years ago. Fell in love with it that I bought a stainless model with cocobolo grips. Both perform very well and are accurate. Anytime somebody ask what pistol I would recommend and I always recommend a CZ 75 variant. Never fails to disappoint

[@iowapanner2223]

Mine eats any ammo I've ever tried and functions despite my weak old grip. Excellent pistol.

[@coupekrause5650]

my first gun is a CZ and this video is great know how for first time users. love this guy makes great videos

[@randyb.5604]

I always put a drop of oil on the spring coils in the sear cage, and trigger return spring when i reassemble. I don't remember where I learned to do that, I thought it was in the owners manual but couldn't find it.

[@keithreh9338]

great vid...don't currently have a cz & miss my p-09 from time to time; my cleaning-lubing process is more involved...guess my ocd pushes me; hoppes 9 or custom blended lube (more on that later) in bore, internal surfaces with fouling (breech face, ramp, mag well, locking block area, etc...bore gets bronze brush 35-50 times to clear our grooves as much as possible (seen used guns for sale with oxidized copper fouling in the bores within the grooves); revolver chambers get 10-15 passes with bronze brush; then use patches, qtips, brushes (nylon, bronze, stainless steel...varies on gun finish) to detail clean tight areas; after that I use polymer safe degreaser spray and hit everything to remove solvent, lube, grime (especially firing pin channels, revolver internals, internal workings on semis); use qtips with degreaser to detail clean tight areas; allow to air dry (shake components to get excess degreaser out of tight areas; meanwhile I take patch with lube & clean magazine bodies & followers; bore & revolver chambers get lubed patches & sit a few minutes while using lubed patch on all visible surfaces (including polymer frames to remove residue, carbon, abraded skin, etc; all lube is removed with microfiber clothes, qtips, patches; lube applicable working surfaces (drip 1-2 drops into revolver internals) & reassemble firearms; work mechanisms & remove excess lube during 1st hour after reassembly...recheck in 24 hours to remove excess oil creep (same thing whenever handling after storage); home brew lube is currently g96 & 15w-40 motor oil in approximately 1:1 ratio (shake aggressively several times during first few hours after mixing to 'burp out' aerosol propellent & occasionally let sit with cap loosened up to allow propellent to dissolve out)...shake dripper bottles to blend mix when using for cleaning /lubing;

[@josephsimonis959]

I don't know what happened, all the sudden i've got a bunch of CZ boxes on the shelf!

[@MrVuicho]

Thank you, Sir! Good instructions for all CZ owners here in Europe as well. I use the brass brush, the CZ brush and patches work fine. Respect!

[@billjensen6216]

I have a cz remi for the wife. And it has an issue with not always feeding properly. It does it with all the magazines we have for it. So I don't think it's a mag issue. I will fallow your cleaning instructions and see if this fixes the problem. Your videos are very informative. Thank you

[@malcolmriggs1767]

To get residue out of those annoying little cracks and crevices, are use carb and choke cleaner spray. It’s a very powerful degreaser as well so you need to clean and oil afterwards.

[@inboxgame550]

I have a lightened spring kit (all 3 springs 13lb) in my Shadow 2 and i have snapped a takedown pin after approximately 5-6000 rounds. Now i use one for training and then i change to one i only use at competition since you obviously don't want that happening during a match. Keep track of your rounds and change it out when you feel it's necessary.

[@sootch00]

Thanks for the tip. Competitive shooting reveals a lot. I used to run the 1911's shooting IPSC matches and what can go wrong, will go wrong.

[@JunkfoodZombieGuns]

Love my 75, and my Shadow 2. The Shadow is just on another level.

[@robertashworth1568]

The shadow is single action only correct?

[@JunkfoodZombieGuns]

@@robertashworth1568 My Shadow 2 is double/single action, just like most CZ75s. I am pretty sure that CZ does make single action only variants of the CZ75. Not sure if the Shadow 2 is one of them, but I think it may be.

[@JunkfoodZombieGuns]

@@robertashworth1568 That being said, it can be used just like a 1911, carried cocked and locked, which would essentially make it like a single action only pistol in that mode.

[@robertashworth1568]

@@JunkfoodZombieGuns ok. Very ice

[@JunkfoodZombieGuns]

@@robertashworth1568 It is. I posted a video with it in it a while back, along with an FNX-45 Tactical. That's a fun one too.

[@brianhondel8348]

I've always gone over every crevice with hoppes 9(scrub if needed) , wipe dry and then follow that up with hoppes oil on a patch and then wipe off the excess oil. Takes more time but hasn't failed me yet. Thanks sootch

[@sootch00]

Thanks Brian. I've done the same in the past. For this video, I wanted to keep it as close to CZ's recommendations but as long as you go back with oil, you're go to go.

[@jbutle4]

Love my CZ 75B and my CZ 75 Compact. So easy to shoot and accurate.

[@AMF96]

I have a CZ 75 Compact that I bought new almost 5 years ago and love it. It’s currently the only CZ Pistol I own but I’m still considering getting a CZ 75B or CZ 75B Retro Edition. Can’t go wrong with a CZ! 👍

[@francujka9875]

I absolutely love my CZ 75B. It’s the perfect pistol

[@Tadicuslegion78]

Well I use cleaning gloves to minimize how much lead and chemicals get on my hands, and then I use 2 of those green cleaning mats, a small pistol one on top of a shotgun one just to all the excess oil that may or may not seep through the first mat is absorbed into the 2nd and not my table. And also I tend to spray my CLP outside in the backyard away from the house just to make sure I’m as well ventilated as possible. And also I have a roll of paper towels at hand just in case. And then when I’m done I try to avoid touching anything until I’ve thoroughly washed my hands in cold water

[@jillianr1]

I found this extremely helpful and clear for my first proper clean, thank you so much! You are a great teacher.

[@calishark408_3]

Just cleaned my CZ while watching this as a refresher. I can’t like this video again so...LIKE

[@kfeltenberger]

Excellent video! One thing, though...I'm not sure it has a low bore axis as the barrel isn't that much lower than it is on other guns (when I compare my CZs to 1911s, Glocks, Hi Powers, and Caniks). The Glock and some other polymer guns have a much lower bore axis. What the CZ-75 does have is a smaller slide (but corresponding higher frame sides) so there's less reciprocating mass and the beaver tail allows a higher grip.

[@WiitRiic]

Thank you Sootch, always love your videos. Thanks to your recommendation, I got myself a RAMI and a PCR. Love it!

[@willwilliam217]

I just got a rami, put cgw night sights on it yesterday. It is a very nice pistol.

[@scotttish7808]

Thanks. I just bought a CZ 75 B Omega. This walked me through the cleaning process without a hitch. Great info, well presented, easy to follow.

[@1EDsson]

CZ PCR fan here!! Fits my hand better than anything else! ave a feeling it won't be my only CZ.

[@Asifkhan-ip8ft]

I found this handgun one of the most elegant and beautiful 💕. Love it. I wish I could find it in Pakistan.

[@jdk_360]

I'm definitely a cz fan. Love my compact PCR and suppressor ready p10c.

[@77Infidel]

I am a lefty, So I chose the PCR. Unless a hammer fired gun has ambi safety, it is hard to carry cocked and locked. I love the decocker on my PCR. I have bought and sold many guns but any CZ will be handed down to my offspring.

[@floydsouth5770]

I really liked the accuracy and quality of your video. I have the same pistols and just love watching everyone else's techniques as I already have mine. Great to bump up against what I am doing vs others! Keep on keeping on!

[@eddyj01258]

I recently bought a 75 bd and an sp01 Tactical and love em both, great shooting guns.

[@antouab221]

Thx sootch00, this video made my day, not because I needed a lesson on how to clean my CZ pistols, but just to see this awesome pistol talked about and cleaned by the guru and the video makes this cold snowy day just a bit brighter and warmer. Now to my hot coffee :)

[@sootch00]

Awesome! Glad I could make your day brighter! I was looking for an excuse to get my CZ 75 out and this was the perfect timing. Thanks Antoua!

[@jimbrown8818]

I have found microfiber towels work great for gun cleaning. I keep one slightly oiled in a Ziploc bag inside my range bag for quick wipe downs.

[@stevenewcomb2702]

Primo video! I like to use a bamboo skewer with patches. Gets that crap out of slide rails & other tight spaces. Thanks Sootch!

[@georgebailey5328]

Recently purchased 75sp01... love it, very smooth shooter! Thank you for a very simple how to video for new shooter like me... I’m over 50 and learning fast!! I use Hoppes for solvent and G96 clp and aerosol gun oil/ cleaner. Kroil for inside barrel after solvent.. thanks for your honest review this gun... Maby for next vid a tutorial on proper holding of gun to get best results ... two hand... lots of vids w very different styles... that will help me keep things simple... more accurate!!!

[@protectiverailroaddad7541]

The bore axis isn’t really that low on the CZ75, it’s the short slide that gives that illusion. The bore axis is pretty much on par with other hammer fired guns, it just the slide isn’t as tall as say a sig/hk/beretta/1911. Measure from the beaver tail to the bore and see for yourself

[@Banshee365]

Nobody ever realizes this.

[@michaelpeila8794]

Everytime I hear the low bore axis thing, my eyes roll. I LOVE my CZ's, but my god I hate the marketing .

[@protectiverailroaddad7541]

TheDoonzman bore axis is the relation the bore has in regard to the hand or how close in line with the hand, nothing to do with how much slide material is above the hand. The slide and bore are two separate things. That’s why guns like the Rhino and Alien are truly revolutionary guns, the bore axis is in line with the knuckles more or less but there is still material above the hand. I get what you’re saying, I wish others would as well. We are now in a low bore axis short trigger reset crazed gun world. That’s all you hear about anymore. Not saying that’s a bad thing but it’s just getting to be annoying

[@ThisCanNotBTheFuture]

Correct. According to one chart on the web, the CZ 75 comes in at 1.57" so low-ish for a hammer fired gun (significantly better than a Beretta 92 or a 1911) but not in the same low-bore axis league of the P-10c, glock, steyr, and other low-bore striker fired guns.

[@Fedaykin8]

I love my P-01! Seems like one of the harder models to find too, took me a while to get one!

[@Steelcurtain75]

I just added the 75 compact to go along with my 10pF. That’s the long and short of it. 😊

[@haileymaya2030]

No disrespect intended I see your videos at least once or twice a day when I'm not working and they are very informative thank you

[@sootch00]

Thanks Brother! I am honored.

[@mctourer5549]

Hey Sootch, check out Strike Hold! It's like CLP but better. I've used a lot of Break Free CLP in my days, but since switching to Strike Hold I've never looked back. I am a HVAC mechanic and I use It on everything at work as well. It's good stuff!

[@sootch00]

Thanks Brother, I'll check it out.

[@MrHurch]

When taking out the slide stop, I use the bottom of a magazine to pry it out instead of my fingers. Little bit easier that way, especially if the gun is still new.

[@willwilliam217]

My rami is only a week old. Was having a hard time disassembling with a magazine. A nickel seems to work pretty good. Will try the magazine again in the future once I get more comfortable holding the slide back to 1/2 cocked hammer. Awesome pistol, very accurate and little recoil for a 3” barrel.

[@hoppahaole3155]

I also set the slide upside down push on firing pin block and firing pin so the pin is sticking out of breech face to push out any goober that might of got in while cleaning, I just use a q tip and wipe tip of firing pin.

[@easy56wedge]

If you move the hammer back to its first stop, the lines match up perfectly. You don’t have to go farther than that as shown in the video. Makes it easier to hold the slide in place when tapping the slide stop out.

[@InfBerBat143]

With the omega System, you must full cocking the hammer.

[@erg0centric]

Half cock, line up witness marks, push gun against your workbench. Lube your magazines with Teflon spray, not oil. Then the dirt won't stick

[@down2wunderland516]

I've watched many cleaning videos for the CZ's this video is the best cleaning video on how to and how not to. Perfectly demonstrated! Thanks for posting!

[@spacebear49]

Alcohol, CLP, M-Pro 7, Boresnake, rags and a silicone cloth. Works great on pretty much everything.

[@saxtx09]

Watching this I’m reminded of the scene from Forest Gump where the drill instructor is yelling at him during the rifle disassembly. “Sootch why did you disassemble the weapon so quickly?! Because you told me to drill sergeant”.

[@joeperez3520]

Thanks for this video. Awaiting delivery of my CZ 75B Retro, and wasn't sure if there'd be a thorough video on how to clean it. How little did I know just how popular the CZ 75's are.

[@kimleith1378]

Mine's on order. Been putting it off way to long. The wait is brutal. 6-8 months.

[@gunsquawk4443]

That Hoppes is old school, Don. I found Ballistol spray works great and doesn't damage any finishes.

[@sootch00]

Yeah but I'm old school! lol! I also use Ballistol but I was trying to stay kinda basic. Ballistol is awesome. Thanks Brother

[@tomasrecinos448]

I have 2 p01 1 p07 and planning on getting more cz just love them

[@robertbranyan794]

I used my new CZ 75 at the range. The second clip jammed when I went to shut. I was told I to easy on the slip action when loading the first round? Is this true?

[@tomasrecinos448]

@@robertbranyan794 this are military grade tools i would recommend you to shoot is as much as you can to break it in once all the parts in the guns are loosen up they should run with no problem

[@spartaninvirginia]

Ballistol for everything.

[@sootch00]

Ballistol is a staple here as well. Thanks Brother

[@HillbillyNitroUSA]

Ballistol all the way ! 💧

[@gamerdaddy8597]

^bump

[@gregcampwriter]

Agreed--thanks to Hickok45, I've become a convert. It does everything needed through the cleaning process.

[@spartaninvirginia]

Bloke on the Range is the reason I tried it. Haven't looked back.

[@August-Iner]

Danke Sootch für die immer guten guten Videos. Hab seit einiger Zeit eine 75 B als Backup Waffe und sie ist Perfekt. Grüße aus Deutschland

[@uncletom2962]

Dieter Dengler , ich glaube Dir ist nicht klar was eine Backup Gun ist. Gruesse aus Arizona

[@AtomicSea]

This works just as well for the Jericho/Baby Eagle. Pretty straightforward

[@orygun9mm]

Thanks for the info. I ordered that very CZ yesterday. Can't wait for it to get here.

[@sootch00]

You'll love it. Thanks Brother

[@orygun9mm]

Can't believe how good this pistol is. I was literally laughing because it's so easy to shoot.

[@AntiFederalist58]

Excellent video, once again. I've been shooting CZs since before it was cool. I recommend changing all of the springs every 5000 rounds.

[@sootch00]

Thanks Chuck! I appreciate the heads up on the Spring. It's way past time for me! lol!

[@mhinz2]

I have a CZ75 SP01; totally awesome. That little extra weight on the nose from the pic rail vs. the base 75 really makes it just a little nicer to shoot. Everyone that tries it really likes it. Yeah it's big and heavy, but that's what's nice and makes it a great gun for going to the range with so you can really concentrate on becoming a better shot. Low recoil and great for new shooters.

[@sootch00]

Oh yeah, the SP01 is awesome on the range. It rivals my Hudson H9 by being so flat shooting. Thanks Michael!

[@apb2887]

I just installed a set of Dawson precision night sights on my P-01 a few days ago. I'm really surprised that Sootch didn't change out the factory luminescent painted sights. They are the worst sights I've ever had on a pistol in my life

[@apb2887]

@@ejhagan Mine never worked, even holding them up to the light they wouldn't glow in the slightest. Tough to see in the day too

[@wisnog99]

I own a Pre B CZ-75 and I love it so much

[@blueslurker1]

Try using the little brush that came with the gun for applying and spreading oil to the slides.

[@bobw3]

i was a 1911 guy until I bought a 75 SP 01. Then a 75 B Compact to carry and then a 75 Cold War Edition. I've never had a failure to feed or eject or fire or ejecting brass hit me in the face with a CZ with any ammo. The only problem ever was when I put a short mag in a full size gun and the ammo wasn't high enough to feed. That was user error, not the gun.

[@richardescareno2433]

I'm a CZ fan! Awesomeness.

[@HillbillyNitroUSA]

Great video bother Sootch! Cleaning firearms is like therapy for me. Just watching the video and hearing the sound seems to mellow me out.🤷‍♂️🤣 Gun nut...💧👍👊

[@sootch00]

Lol! Thanks Brother! I felt the same way doing the video.

[@kevanschaum9452]

I use ballistol and Lucas oil & grease. I have 3. Rami, Shadow2 and a Tactical sport orange. Love them.

[@DarlingEbony]

I just got an SP-01 and a Rami. So this is helpful.

[@tinman8972]

I can't say enough good things about this weapon. I am going to lubricate the slide with molybdenum grease (applying it very sparingly and wiping off all excess). We'll see if it makes it smoother or easier to rack.

[@AMX86]

Gotta agree, CZ75 is a great firearm. Have 3 myself, sweet shooters, accurate, reliable, love the solidness of the arm. Nice refresher on CZ recommended ckeaning. Thanks much.

[@sootch00]

CZ are great firearms. No better range day than a good CZ 75 on deck. Thanks A M!

[@gunsquawk4443]

I have 2 CZ75bs in 40. And a Sarsilmaz 45 CZ copy. Best guns ever made!!

[@Doggie_San]

Just got my first gun this week (Shadow 2) and this video was really helpful! Thank you so much

[@06GTblue]

Thanks for the video! I have a CZ75 BD Police.

[@teejayArts]

Who’s watching in 2024?

[@joshuapowell9501]

I'm here

[@Jaybird-oo3ih]

🙋‍♂️

[@johnivanp]

Makes me miss my original CZ75 from the 80s. Good video

[@sootch00]

Thanks John!

[@johndeere1951a]

Metal - no plastic -CZ's and Walther's in my arsenal 👍👍

[@theflaver]

very helpful thanks. Just brought my CZ 75 Compact home so time for first cleaning and then the range!

[@roberttrujillo4431]

I have the CZ 75 D compact and CZ 75 P-01 and have been having issues with failure to load on both. Both guns are new, I have maybe maximum 300 rounds through each. I have tried different ammo, and each time I take them to the range, I'm having failure to load issues with both. Yesterday my 75D Compact froze up. It would not fire, so I dropped the magazine, tried pulling the slide to empty the chamber, but the slide was stuck. I pulled the hammer back and tried firing it down range but just got the click of the hammer, I did it a second time and nothing. It finally expelled the round on the third attempt. I thought it was just a fluke, so I put in a different magazine, and after the third shot, the same thing happened. I couldn't even pull the slide back. everything was just stuck.

[@bryancarmody1617]

Great vid sootch! Appreciate all the maintenance vids!

[@jamespage4092]

Thanks for your instructional videos and warm ending admonitions.I learn much and am encouraged every time I watch.Being a plane mechanic by trade,I've used Cotton Qtips on small parts,and wore health-workers gloves to prevent marring critical parts.Would these steps apply to gun maintenance also?Just a thought.God's blessings.