Hi Guys, The above video is about setting up the spark plug gap and what model to be used. Short reach Spark plug Bosch - W145Z1 / RE Part No: 141148 NGK - B7HS Champion - L82C Regards, BULLETO 6360703486
Пікірлер: 25
@msharief62733 жыл бұрын
Sir very useful information, And seriously educating is best thing to do. But company recommend. 0.45mm is for a battery which less amps (battery 1980s) suppose if you put 12v 5 amps then bike will choke in high end RPM it has to be a little more than .60mm. My personal experience.
@bulletodiy45483 жыл бұрын
Technically more gap will eat out more voltage and causes engine to run rough..
@anilverma-un5bf3 ай бұрын
HI ...I am facing this issue. My bike is 1977 Std 350cc, running on 6volt stator and 12 volt condenser and ignition coil with 12v 5 Ah Battery. I have checked spark plug gap, CB point gap, tappets, Ignition timing, compression and carburettor ...all good as per manual. Bike starts and idles excellent. Runs smooth with good power and pick up, but when I open throttle and crosses 50-55kmph it starts sputtering, lowering the accelerator, bike runs fine. Plug is Bosch HW 145 Z1. Is this coz of plug gap? As per your statement the gap should be .60mm. Need help on this...TIA
@SRakesh4203 жыл бұрын
Just a suggestion,not many videos are made on the avl bullet or the machismo 350a or the machismo 500. Keep up the good work and your content helps with understanding my bullet a lot more.
@bulletodiy45483 жыл бұрын
Thank you. Very few AVL's are available where I stay. Once I get a chance to work on them. I'll try to upload topics on them.
@shamdudaganvi9609 Жыл бұрын
Sir pls carburetor tuning bagge video madi old bullet
@nirmalbabu77992 жыл бұрын
nice information 👍
@adityaveerkaushik Жыл бұрын
What should the gap for 2003 electra without battery start limited edition?
@bulletodiy4548 Жыл бұрын
W145Z1 with 0.45 to 0.5mm gap
@adityaveerkaushik Жыл бұрын
Thanks
@vikramrawat24002 жыл бұрын
Super guru...
@karthiks63262 жыл бұрын
Wah what a focus of camera on rocker covers🤦
@chandrashekar-dr2xr3 жыл бұрын
Sir Hawksa blade use Madi check madboudha
@bulletodiy45483 жыл бұрын
Hi, Hacksaw blade is little thicker (0.63mm), recommended tip gap for CI Bullet is between 0.45 to 0.50mm. If you are using Hacksaw, ensure it is not passing freely in between the gap.
@chandrashekar-dr2xr3 жыл бұрын
@@bulletodiy4548 sir where u in Bangalore I want to visit us shop to check my wiring
@bulletodiy45483 жыл бұрын
@@chandrashekar-dr2xr currently I'm in hometown, Udupi. You can contact me over phone.
@aabcbb3 жыл бұрын
Pls, share the link to buy feeler gauge.
@bulletodiy45483 жыл бұрын
Generic 1 Set Metric Feeler Filler Gauge with 20 Blades Feeler Valves Measure Tool www.amazon.in/dp/B01AG9DNK8/ref=cm_sw_r_apan_glt_fabc_4EBHJR0YX5WT339VMTSX
@bulletodiy45483 жыл бұрын
I had purchased it from shop, which has pointed blades
@aabcbb3 жыл бұрын
@@bulletodiy4548 Thanks..
@vinodkaliyamoozhy19692 жыл бұрын
R ee feeler kg elleenth sikthe?
@bulletodiy45482 жыл бұрын
Special tool/machine tool shop
@shankarprasadagrawal19812 жыл бұрын
Very nice video sir 👍🙏 mere bullet ke spark plug ki chudi per halki oil a rahi hai main apni bullet ko mahine mein एक-दो bar hi nikal pata hun kya oil aana koi pareshani ki baat hai kya
@bulletodiy45482 жыл бұрын
Could be Wet Sumping issue... park your bike at piston Top Dead Centre (TDC)
@anilverma-un5bf4 ай бұрын
@@bulletodiy4548 To avoid wet sumping, i always park my bike on centre stand, it has never wet sumped again