If you're worried about the bolts coming loose, it's probably a better idea to put some blue Loctite on the threads rather than over tightening them (which I would probably end up doing).
@bungel6573 жыл бұрын
I would like to add a couple helpful hints when installing these types of Tow Mirrors, First off it will be a lot easier when removing the Outer Plastic Covers if you use a Thin Putty Knife instead of a Flat Blade Screw Driver, Also, when your ready to insert the Washers, Sandwich them between a long piece of Scotch Tape and leave a 1" tail on it, then poke a Hole through the tape so it will be easier to insert the Bolt through. At first I used 3 Washers, which made my Mirrors Perfectly Level, "BUT" when I went to install the Plastic covers, they would not Snap Shut because the Top underside of the Mirrors Arm was to low which prevented the cover from closing, I then lifted the mirror up which took some pressure off of the cover, which let it snap close, "But" when I moved the mirror to close them the covers would Pop Off, So I ended up using just 2 Washers, which did the job, I would also recommend that you use Lock Tight on the Fine Threads of the Bolts when you tighten them down.
@_flexxx_ Жыл бұрын
Mu thoughts on what you commented.... do you think using the two at the mirror and maybe one on the top stud at the base mount might give the proper angle with out pushing it out from the door to far and making a gap?
@bungel657 Жыл бұрын
@@_flexxx_ You can try it, But doing so may require you to purchase Two Longer Screws for the Top, because adding Washers to the bottom may cause the Top to be to far from the mounting Holes, But I and many others found that Two Washers at the Top is all you need to make your Mirrors Level, Just make sure you use ether the Blue Locktite or the New Orange Locktite, which is in between the Blue and Red, But is easy to remove. By the way, If I ever do this again, I would take one of the bolts to my local Hardware Store and Purchase 4 that are just a little bit longer, for the top Right and Left side, that way when you add the Two Washers to the Top, you will gain back what you loose when adding the Two washers, But then again, I have had mine on for Two Years, and they are still Holding tight with the added Blue Locktite.
@benjamindavis4130 Жыл бұрын
Appreciate your tips
@B-Smalls Жыл бұрын
Did it hold up over time????? And is it hard to wire in turn signals to a work module with no power windows or mirrors?
@ronthompson23664 жыл бұрын
Add just a little finger nail polish or light dap of blue loctite to the bolts. Keep them from vibrating loose and snug up easier an prevent [less chance of] stripping. You two are the best, I say it every time. But it truly is refreshing to see a young couple who are a team like the two of you. Continued success... so now what's next for the build ....
@TruckMaster4 жыл бұрын
Thanks Ron we have our order in for HSP parts also Anthem wheels are ordered as well
@boards65dilligaf204 жыл бұрын
Good job - much better looking!! I will have my son do his 2500HD and my Duramax!!
@saltysteel39964 жыл бұрын
If you have a strong magnet you can shave down the thickness of washers on a belt sander to dial in the level-ness just dead perfect. It's like making your own custom shims.
@davieboy19703 жыл бұрын
Thank you for posting the video. I just put a set of aftermarket ones that I got off eBay on my Ford F-150. And it's driving me nuts how unlevel they are. Now I know how to fix the problem. Thanks again guys
@revived_diesel44454 жыл бұрын
The mirror always look different because the drivers mirror is twisted farther out and the passenger side is twisted closer to the door
@TruckMaster4 жыл бұрын
I never knew that
@JoesGarage8314 жыл бұрын
Yup, all mirrors for vehicles are made that way, the passenger side mirror is farther from the driver, so it has to be at a different angle for optimum viewing angle. From oem factory the passenger side is engineered that way too, the glass has slant to it instead of the whole housing, if you want to check it out...
@justinusaf183 жыл бұрын
Hahaha I was about to send my mirrors back because of this!
@jamesherald39274 жыл бұрын
Great content. Happy wife is a happy life be safe guys
@hotshot007 Жыл бұрын
I'm glad I watched you. I'm going to add 2 washers before I put my new mirrors on 👍
@stevenjohnson75712 жыл бұрын
Just bought a silverado yesterday and hated the mirrors leaning. Going out tomorrow and fixing this. Thanks for the tip.
@nickhutcherson4 жыл бұрын
Sweet video man glad you leveled them! Just got my stay tuned decal and I love it! Thank you for your time and effort!
@TruckMaster4 жыл бұрын
Awesome! Thanks Nick
@UnhappyDuramax3 жыл бұрын
Truckmaster, I’ve got a problem with this method. I had yitamirrors on my last truck and followed this leveling method and it worked. Now I got boost mirrors, and when you try to put those spacers in there, even when you snug it back down it wobbles and won’t get solid meaning that spring behind the little lever wedge is just pushing out far enough now to not hold the mirrors tight. Does that make sense? Please message me I ended up putting spacer in top of the 3 bolts that hold the mirror to the door.
@alphapackoffroad4 жыл бұрын
I had to do the same thing to mine after I installed the newer style mirrors!!! All cat eyed chevys need the washers. Mine are perfectly level. I used 3 washers on each side.
@alexanderweller65093 жыл бұрын
How thick were the washers you used. I couldn’t get the cover back on when I used 3 washers
@alphapackoffroad3 жыл бұрын
@@alexanderweller6509 they were real thin i believe. If coverwont pop on then try 2 washers. Or trim cover a little where its hitting.
@anthonylucia6500 Жыл бұрын
Watched this when you first posted three years ago. Now i’m back in 2023 (with inflation and the price of stainless hardware) to make a joke and say you should change the title of the video to “Spend 8 dollars to level your tow mirrors”. Lol.
@scottwilliams50594 жыл бұрын
I have an 2001 hd project so keep the ideas coming 30 over injectors 68 mm turbo 5 inch exhaust so far
@TruckMaster4 жыл бұрын
Nice Scott
@Chevyfan-tl2kw4 жыл бұрын
Video
@davidwolff88784 жыл бұрын
you need a shorter handle ratchet the longer the handle is a greater chance of striping
@reddirtdiesel50634 жыл бұрын
I can't believe you are almost at 100k subs, it's so awesome. 👍
@TruckMaster4 жыл бұрын
I know it’s crazy man
@mrkanook92264 жыл бұрын
You need a longer extension on the drill
@chriswheland98954 жыл бұрын
I like both of y’all trucks. The cat eye body style is the best.
@salty_terminal_civilian53743 жыл бұрын
Damn I'm jealous of the truck and the wife lol. Wish my wife would help me with the Tahoe lol.
@Ryan87752 ай бұрын
I have the same mirrors, and this method will leave a gap at the top and when you hit a bump your mirrors bounce. Wish there was a better way to get rid of that look.
@repairvehicle4 жыл бұрын
Any idea if tuned duramax runs hotter in terms of egts and coolant temperature?
@petek65224 ай бұрын
I've been watching your videos for years and i never owned a chevy pickup, im getting my first, it's a black 95 silverado 2500 regular cab 4x4 and my second modification will be tow mirrors , are you happy with those still ?
@05llyduramax434 жыл бұрын
I put 3 washers on mine. Modified the cover and I also put super glue to keep the covers from flying off
@zachrouse52344 жыл бұрын
Wifemax looks awesome and it’s not even done ✅!!
@FarmerSteveO4 жыл бұрын
I went 3 washers out of personal preference, had to lightly grind some plastic on the bottom side with the dremmel on the cap to get it flush, but looks factory. Just have to know any mod on any part ( like my grinding) will void warranty. Question, "Do the chickens have large talons?" JK 😂
@knoxvibes99182 жыл бұрын
hey do you have a problem with the passenger mirror being able to see behind on the top passenger side ? because i cant see the back of my truck on passenger side
@northwestoff-roadopportuni71764 жыл бұрын
Helpful hint: I super glued 3 washers together before installing
@TruckMaster4 жыл бұрын
Thanks
@Eastsidee8173 жыл бұрын
What size washers?
@CCCC-tq8yo5 ай бұрын
?
@shanelebeau13154 жыл бұрын
Just a little FYI the mirrors are diff angles side to side dirty max jack did a whole video on this exact topic check it out. It’s all abt the angle the driver sees from driver seat.
@tylermaassen4 жыл бұрын
Looks alot better!!
@tadheath58564 жыл бұрын
Reason everyone likes the wifemax so much is.....it came from diapers to almost depends build!!!!!....👍👍👍👍👍👍👍👍
@tonylucero11402 жыл бұрын
We need a video on what to do when you drop a washer in the bottom base of the mirror lol crappy part I can’t even use a magnet I bought Ss. You make getting them top 10mm on the head of them bolts look easy. Mine wanted to round out the head. Thanks for your tips.
@owenpullen63564 жыл бұрын
Will this work on the older mirror
@tmspete73542 жыл бұрын
HER tow mirrors. Love that pride.
@aaronpodgorski16174 жыл бұрын
Awesome content Josh&Melanie
@TruckMaster4 жыл бұрын
Thanks
@christopheradams740011 ай бұрын
Do you have a video of wiring these mirrors up?
@asianpersuasion18074 жыл бұрын
I think it looks way better. Wife max on point
@zumspeed26884 жыл бұрын
I have those retro fitted on my 98 Silverado so ima give it a shot
@domeniccaldarelli44434 жыл бұрын
i’m about to install some on my 97 yukon
@zumspeed26884 жыл бұрын
@@domeniccaldarelli4443 super easy
@domeniccaldarelli44434 жыл бұрын
zumspeed 26 any tips?
@wbn47603 жыл бұрын
Driverside looks level. Great job. 🤘👍
@kozmicflush980 Жыл бұрын
The passenger naturally sits different, that's why driver side is perfect
@jamesjordan74602 жыл бұрын
Great video bro! just had replace mine cause I was side swiped bout 90mph on freeway by another truck....can you believe and luckily all he clipped was my drivers mirror, it sounded like he took whole side of truck with him....I did buy exact mirror for driver side and appears is opposite of yours....my passenger mirror looks level and driver looks to be at angle? great trick shimming and I may do mine as well but really only 2 people know....me and you so I might jus leave. LOL!! Thanks!
@stealthcon69752 жыл бұрын
Hey truck master since u built a few dirtymax on the cat eye front bumper bracket are they Interchangeable with the gmc without cut and welding
@LordTominator4 жыл бұрын
Looks great!
@TruckMaster4 жыл бұрын
Thanks
@salamander25474 жыл бұрын
1/4in plastic spacers worked perfect on mine
@HannaberryJB3 жыл бұрын
Bought some China tow mirrors and can't get them to adjust far enough in to see my rig or tow vehicle. Best I can do is watch the white line go by beside my vehicle. Do the Boost mirrors actually allow you to see your tow vehicle? And does leveling change the viewing angle much? Or is it more for how it looks to others while truckin' down the road?
@hollywall9626 Жыл бұрын
Did you ever figure this out? I’m having the same problem…
@bigturclakelife89804 жыл бұрын
Wow that’s night and day man
@seabee734 жыл бұрын
Thanks for the tip. Mine are finally level now.
@ARdave3112 жыл бұрын
Hey man I had a question for you on those mirrors were they the ones with the turn signals? And if they do have the turn signals were those mirrors plug and play? Or did you have to run wires for the blinkers to work? Been really wanting these mirrors but I do not want to have to fool with wiring I’m hoping they are just plug and play
@andrewt2482 жыл бұрын
They should come with shims from the manufacturer when they say it fits this body style of truck.
@iansampson2515 Жыл бұрын
Where'd you get that shirt!?
@averyyuzicapi7233 жыл бұрын
Hey you said if you put 3 washers on you might have to mod that covers that snap back on, what did you have to mod on them because I only put 2 washers on both driver and passenger. The driver side one snapped in fine the passenger side however does not wana snap it what did you do?
@chadwhittaker58093 жыл бұрын
Where did you get the mirrors?
@blownbird974 жыл бұрын
Looks good. I agree with your wife, the driver side looks more level.
@clarkwilliams9967 Жыл бұрын
Mine was the same , i used three washers on the passenger and 2 on the driver to fix that issue
@classyjeremygaming4 жыл бұрын
Thanks to both of u i am going to do mine now haha that truck is getting done up looks awesome who makes thoses light head lights
@robbybowermaster62704 жыл бұрын
I know this post isn't about braking, but I have a brakes not holding when I brake boost (I drag race). Is a 2007 GMC LBZ Duramax, have already flushed the hydroboost and brake system and still very poor brakes. No leaks, but just wondering how I can tell if is master cylinder or the hydroboost. Any help would be appreciated.
@Neftali924 жыл бұрын
Cant wait to see wheels on wifemax
@TruckMaster4 жыл бұрын
Same here
@MrTrump-hx4lb4 жыл бұрын
When are you going to make a videos on installing the edge monitor mount for the wife max truck?
@murdered_gmc4 жыл бұрын
my mirrors looked the same way. i actually put 3 washers on one side and 2 on the other to make them look even to my eyes anyway lol.
@colingriswold27654 жыл бұрын
Can’t wait for rims and tires !!!
@547Rick4 жыл бұрын
Looks good!
@jsavage89864 жыл бұрын
wow it looks way better
@HewHolden4 жыл бұрын
Wife max is clean but you’re red truck does look better. Show us how you cut those covers?
@jrodpadilla224 жыл бұрын
Wifemax has come a long way!
@eaanstokes88714 жыл бұрын
Drivers side is level
@UnknownUnknown-se1qu4 жыл бұрын
How do they hold up. Do they shake alot
@joekeller71843 жыл бұрын
I just ordered those mirrors for chevy tahoe
@packwoodperformance4x4744 жыл бұрын
Those mirrors are nice.
@rafaelmunoz163310 ай бұрын
What size washers
@zlspears114 жыл бұрын
How much longer until the new wheels and tires come in
@gilvietor19182 жыл бұрын
Can I do this on my 2003 GMC Yukon 2500 XL?
@solo_volo34553 жыл бұрын
What size of bolt. Thanks
@at1w4 жыл бұрын
Will this work for a OBS Chevy
@f.ll.2 жыл бұрын
What's the inside diameter of the washers
@willtharp74774 жыл бұрын
Why no lock washers?
@thechristianbiker8122 ай бұрын
"Go ahead and"
@bernhard85404 жыл бұрын
it does help the look alottt for sure haha
@phillipkrol33384 жыл бұрын
Dosnt look bad. Boost auto parts does not recommend leveling them. "Our mirrors are designed off of the OEM mirrors, and the OEM mirrors do not sit level. Many choose to level the mirrors out and there are many writeups out there on how to do it, however we do not endorse this. Disclaimer: Leveling the mirrors can cause additional glass shake as well as damage to the mirrors."
@TruckMaster4 жыл бұрын
Thanks for the info 👍
@phillipkrol33384 жыл бұрын
@@TruckMaster no problem. I'm sure you knew this, just didn't want someone coming after you especially if they try it with the ebay knock offs.
@donaldlong96494 жыл бұрын
great video!!
@brendanmacdonsld2macdonald484 жыл бұрын
Put a level on top of the mirrors see which one is more off then the other
@marksomma6169 Жыл бұрын
You would have to be on perfectly level ground
@stephenmireles1363 жыл бұрын
Is it six or eight washers?
@haromaster60862 жыл бұрын
I don’t mind the angle it’s sort of matches the cat eye angle of the headlights.
@joemacdonald96724 жыл бұрын
I'm pretty sure passanger side mirrors sit at a different angle then the driver side.
@garrettguidotti63813 жыл бұрын
They look different because the mirrors are at different angles off the the body if that makes sense
@summitdave87823 жыл бұрын
Her truck it dirtyyyy..The mirrors are gross...Sorry i had to for the haters....Getting that out of the way...lmao...Good stuff guys...
@JaredisOutdoors4 жыл бұрын
almost 100K
@eddiefinch4364 жыл бұрын
She sure is Pretty
@carmen_playz_21123 жыл бұрын
💀🤣 bruh thats his wife
@Joec22x11 ай бұрын
The angled look gives the truck a more aggressive look, leveling it makes it just look bad imo
@lenhofer32144 жыл бұрын
Get a milled billet chamfered plate ....n do it rite
@dangermouse33144 жыл бұрын
Knew it was the level Mirrors 🙌🏻
@erwinnez37354 жыл бұрын
Yes! I love this idea. Thanks wifemax haha #MarriageGoals
@ronnieyoung80493 жыл бұрын
still watching
@mph35004 жыл бұрын
Nice cheap hack. But it works!
@benjamindavis4130 Жыл бұрын
Gorgeous truck 👍🏼
@nathanbrodeur4 жыл бұрын
Josh why don't you level your truck as well
@carmen_playz_21123 жыл бұрын
why did chevy even do that tho
@firstname51344 жыл бұрын
That's what I did to mine
@3324jake4 жыл бұрын
Where’s the giveaway announcement lol
@TruckMaster4 жыл бұрын
It’s on my Instagram @truck_master07
@JAWGA9122 жыл бұрын
*Guarantee you've never backed a trailer up in your life*
@TruckMaster2 жыл бұрын
I was a truck driver for years so…
@TheRhpatton4 жыл бұрын
Why not put a level on it
@mishammer96984 жыл бұрын
Where’s the rims?
@TruckMaster4 жыл бұрын
It’s ordered but it will take about 1 month
@mishammer96984 жыл бұрын
Truck Master oh nice are they going to be colored?
@dl60434 жыл бұрын
Josh ur eyes are fucked up, driver side looks good passenger side needs another washer