SPINFISHER VI review, THE TRUTH! V is BETTER AND CHEAPER!

[@PENNfishing]

Jesse - Thought I would comment on your video as to exactly how and why the Spinfisher VI is an upgrade in a lot of ways, as it seems most of the points were missed. The Spinfisher VI was developed off the proven platform of the Slammer III, not just a rebranded Spinfisher V. I hope this info helps! -Ben at PENN 1.) Gears - CNC gears do not only have tighter tolerances than a standard zinc gear, but the solid aluminum and brass gear material are much more resistant to wear against heavy loading. Sizes 2500-5500 use aluminum and the 6500-10500 sizes use brass which is stronger for the higher loads they need to withstand. These are the same design as the Slammer III, however the Slammer III uses brass on all sizes because of the much higher drag pressures. Spinfisher V used a cast zinc gear. 2.) Drag - This was not a cost cutting measure at all. We moved the drag to a top stack so that it would allow us to save weight in a key location. In fact, the smaller sizes only lost about 5lbs of drag, while our larger sizes actually gained 5-10 pounds of max drag. Our max drags are still more than most anglers use for each size reel, and if you do need more, the Slammer III has you covered. Drags are still sealed like the Spinfisher V. 3.) Sealing - Here is where you missed a main point. Yes, we still use a perimeter body seal around the gear box like the Spinfisher V, but we have also added several seals to be able to reach IPX5. First, we have compression seals between the main gear bearings and the sideplates to stop water intrusion around the handle, a main shaft seal (main area of water entry into any spinning reel), as well as a hydrophobic labyrinth seal under the rotor. These were all upgrades over the Spinfisher V. 4.) Weight - We were able to cut out between 2 to 3 ounces from each size. This was done using a combination of moving the drag stack to the top, as well as moving to a carbon rotor on the smaller size reels (not to be confused with plastics used on entry level reels). Material advancements have made it possible to use carbon materials in places where only metal was used in the past, without sacrificing performance.

[@thesaltysquirrel3425]

@PENN just took a look at a spinfisher VI LL to replace my 8500 V Liveliner that only lasted 6 months of kayak fishing. Saltwater destroyed the liveliner drag first which I repaired, one trip later the slammer drag failed on a 40 lb wahoo, I managed to get the fish in but somehow the spring clicker arm came out and wedged against the spool, I have no idea how, never had it opened before the failure. I didn't look at the drag on the VI as I didn't realize it had been changed, but I was impressed with the liveliner upgrade to seal better. I am purchasing an 8500 (wish you offered the 10500 with the LL) for livebaiting tuna/ono/mahi here on Oahu. We will see how it holds up.

[@cruzweston7630]

I just brought a Penn spinfisher 6 8500 and love the look just brought it today haven't used yet but it looks nice 💯

[@pakde8002]

Thanks Penn, it's good to hear both from end user's experience and Penn's justifications on upgrading the reel. I think the change from zinc to CNC aluminum and brass is a definite upgrade. Except for kayak and surf fishing I don't consider the seals a significant issue, however I would be reluctant to buy a saltwater reel that didn't have any protection because you just never know.

[@jordanwaderosecatfishadven355]

Ben at Penn- My son and I are professional catfishermen on the KingKat tour. I need a Slammer III with a live liner. We are still using Slammer II's with the Live liner. We need a lot of drag for big cats. We do use your conventional reels as well but we find spinning reels to be more versatile. Can we expect to see a live liner version in the future?

[@PENNfishing]

@@jordanwaderosecatfishadven355 Thank you for your feedback Wade! We will take this into consideration! Have you checked out our Spinfisher VI Live Liner model? www.pennfishing.com/penn-reels-spinning-reels-penn-spinfisher/spinfisher-vi-live-liner-spinning/1454458.html

[@sreilly94]

From owning both I’ve to agree and disagree. Is the 5 a great feel and most likely more reel than the average angler needs in a spin reel? Yes. That being said do I think the 5 is better quality than the 6? Absolutely not, it’s sealed far better (yes you submerged your rod once or twice over 3 years, let’s look at the internals in a decade after countless submerging, side by side torture test my money is on the 6 any day of the week) gearing/internals were made of better material with better build quality, that can be put through bigger loads, higher friction (have to account for years of this shit) also, the 6 has as much max drag as I could ask for and seems a consistent drag level (no faults to me from what I can see/feel) to each their own. I love both reels Both are worth the money, if I had to chose I’d go 6 just because from what I see it’ll last much longer.

[@SlotCityFishing]

Shane Reilly even if it’s 3x the cost with marginal gains? No thanks.

[@sreilly94]

SlotCityFishing I bought my spinfisher VI 6500 combo under 200$ retail so idk where you’re getting the 3x the cost figure from

[@SlotCityFishing]

You obviously didn’t watch the video. There are snapshots from the penn website with the prices. I even displayed the solved equation so you don’t have to do basic multiplication.

[@sreilly94]

SlotCityFishing well, I went and purchased a full COMBO from a retail store for less than what you have the reel priced at, just saying. Can find them all day at cabellas, 6500 on 10ft penn rods for under $200. And while you’re being a condescending dick might I add usually it helps doing a comparison video when you’ve actually used both things you’re comparing and also have both products there, on hand to compare.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@C5drummer]

The biggest thing I noticed is that it is "possible" for Saltwater to creep into the reel by way of the screws that hold the side plate. The screws holding the side plate on the Spinfisher V are INSIDE the gasket compared to the Spinfisher VI, where the screws are outside. I still think that both are great reels, and with proper maintenance, each will last a long time. I have the Spinfisher IV 6500LL here in Florida and I really enjoy the reel.

[@SlotCityFishing]

Jim O'Callaghan that might very well be a good point. Thanks for the feedback bro. I didn’t think about that.

[@C5drummer]

@@SlotCityFishing -- Your opinion is still highly valued and highly regarded! It says a TON regarding how much and how often you use your workhorse Spinfisher V and it looked THAT clean w/ little to no maintenance after 3 years of use! Who WOULDN'T want that reel! Pretty stellar reel!

[@bloodybrit127]

With respect i would disagree. I dont think the V is inherently better than the VI. I do think that PENN used some cost cutting measures in some areas but that was so they could push those resources to other parts of the reel. 1.For the drag system I'm not really pushing my drag that high because the rest of the reel wont take it. 2 .It is definitely better sealed overall 3 .Amazon is selling combos really cheap now (but sill more expensive than the V) 4.The VI gears are much better especially 6500 and up (The V drag can hold up to big fish but the gears cant over long use in my experience) 5. Its lighter 6. Better balanced(imo) However 1.I prefer the drag sealing on the V 2.The extra seals don't make it submersible and the V sealing was adequate 3 .Phone companies pay alot for ipx testing put the cost into the final product so tested definitely mean more $$$ but untested doesn't necessarily mean worse sealing(tsunami shield isn't IPX tested but damn its sealed). 4. Even if i dont use it the drag system is better on the V Better bang for your buck? Sure V is better but not by much rn. Is the V inherently better than the VI? No because if you are pushing that drag to the max those gears wont take it and you should get a Slammer III Best, Kyle

[@SlotCityFishing]

Appreciate that perspective man

[@Machster10]

It depends. The VI has the good all brass gears but only in the 6500 models up. The VI has better sealing. The V (on my 6500) has the better Slammer drag system but located at top of spool. It actually feels better and much more adjustable and smoother than in this configuration. The bailess 6500 V is painful ergonomically though. I really like the size and weight and concept of the VI 5500 in long cast version but the gears are aluminum and they don't make it bail less. The Slammers are awesome but the spools are sooo tiny. As a surf caster I have gone to Spinfisher VI long cast in 6500 for heavy plugging. It has all brass gearing and the long cast spool. It very smooth and tight. An awesome reel. Too bad no bail less model though.

[@SlotCityFishing]

All great info and I agree thanks for watching!

[@taymerelane]

I know you said plugging, but for beach fishing, soaking cut bait, is there a risk that the line will come off the line roller on a bail less reel due to temporary slack from wave action? Are bail less reels only for lures, not bait?

[@Seanj1193]

One thing to note, the spinfisher 5 the sideplate screws are on the inside of the rubber gasket where the spinfisher 6 the screws or outside the gasket, just something to think about

[@lnelygacha6424]

Why is that Significant?

[@Seanj1193]

@@lnelygacha6424 if you have a sealed off area for water intrusion, does it make sense to have screws within or outside the seal, on the outside there is no risk from water intrusion.

[@SlotCityFishing]

Never thought about thatv

[@Seanj1193]

@@SlotCityFishing I exclusively use zeebass and van staal reels now worries now

[@SlotCityFishing]

@@Seanj1193 dang big balla

[@monkeyman4131]

OK, I have a lot of Penn Reels, my first ones were bought in 1982. A 320SS, 330SS,430SS, 5500SS, 650SS , 850SS and 5500SSV, 3200SSVI, 6500SSV, and a 320 GTI . Ive never had any problems with any of my reels at all. Most were made in " The USA ". My 320SSVI i bought when they first came out. No wories I live in Daytona Beach , FL . five min .from the beach and fish often. Surf and the " ICW " Halifax River. As far as the "DRAG SYSTEM " goes, there is NO "Slamer" drag . All Penn Reels ''SS" have the " H-T 100 tm " drag system. SS,SSV, SSVI. The "Slamer III " have penolic-coated carbon-fiber washers. This one is " sealed to IPX6 " specs. The other SS reels are " IPX5 ". There are very few Penn SSV's left. They are a bit less money and ar as good as the "Newest" SSVI's. I don't work for Penn or any dealer. I'm just a long time user of Penn Reels and Rods. Thank you, Tom , Daytona Beach , Florida.

[@SlotCityFishing]

it literally says slammer drag on the reels. the difference is the drag is the same as the reels in the penn international series and the drag stack is located on the bottom of the inside of the spool. im going to respectfully disagree with you on this. appreciate the feedback tho brother thanks for taking your time to watch the video.

[@SaltyStrikes]

Bought the V 5500 Black Friday weekend for $79 at Basspro shop and just bought the 4500 today on the Penn sight for $69, do I really need another reel? Who cares this is a great deal😁😁

[@SlotCityFishing]

Salty Strikes it really is man. I’m tempted to sell my slammer iii and by a few of them.

[@SlotCityFishing]

Keep makin vids bro. I checked your channel out and subbed.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@Danny-qi4lp]

No matter what Penn says, the Spinfisher V was built on the Slammer III platform and the Spinfisher VI is built on the same platform as the Battle. In a nutshell, Spinfisher V is a stripped down Slammer III and the Spinfisher VI is a dressed up Penn Battle.

[@SlotCityFishing]

Hell yes. Someone said it.

[@joeynunez9424]

If you are going to challenge one of the most popular mid-price point spinning reel platforms and an excellent ICAST performer with the VI, you have to tear these reels piece by piece and see the differences... clear clear differences in gearing durability, in sealing (main shaft seal, sealed bearing at the AR clutch, etc.) and the variety of models like the live liner, the long cast, and way way better line lay than is found on the V.... it's just bad reel maintenance to not take your reel apart and work on it, especially with the ease that Penn gives you to do so... big supporter of the channel, like your videos, just think you missed it with your incomplete review on the VI

[@SlotCityFishing]

Yea I could’ve been more thorough thanks for the feedback.

[@antaranexpress7502]

Here in Indonesia, many pro says that spinfisher V is better than the VI. Just bought the VI 5500 LC , and they said I should pick up Slammer III instead of The VI... Nice & comprehensive vid, Bro ...

[@SlotCityFishing]

What reels do you recommend?

[@seamurda100]

I appreciate your honesty. It takes guts to share an opinion like that. Penn fanboys getting butt hurt, lol. I've got a spinfisher 6 6500, I like it alot. I think the CNC gearing is worth an extra cost but not to the extent that they are charging. The Battle 3 finally got CNC gears but a 6000 is like 135 dollars. Why not get a Daiwa BG for 90 dollars? The fierce 3 is almost as much as a BG. Thats ridiculous. I have 3 fierce 2 liveliners. Only reason I bought them is that is the lowest you can go for a live liner. They need to hear this kind of feedback. I wanted to buy a battle 3 but no way at that price point. BG all day for that price.

[@SlotCityFishing]

CatfishCarl this is a solid comment. I agree.

[@seamurda100]

@@SlotCityFishing Thanks. Navy Vet. Gotta tell the CoC how it is.

[@vladimirlopez7840]

My Penn spinfisher vi’s have been workhorses. I admit I’m a Penn fan boy because I can open them up take them apart clean and lube etc. Diawa is pretty clear that they don’t want you taking them apart. Shimano is of course a great reel but I love my Penn’s.

[@SlotCityFishing]

Agreed bro

[@eves08109]

New subscriber here! Hey Jesse, I thought I could give you some valuable feedback on the Spinfisher V 7500. I bought this reel brand new in 2016 and I may have used it 50 to 75 times up to this year. I take exceptional care of my gear and to give you an idea just how well, I have never even had a $30 reel seize up from salt water. With that said, this Spin Fisher has served me well however I took it out shark fishing Tuesday night and for the 1st time I really locked down on the drag fighting a 100 lb Sandbar shark. On his initial run I probably only around 7 lbs of drag before I started to feel uneasy about the feel of the drag so I backed down to the point where it was a smooth release. Now my concern is this reel hasn't been used enough for the carbon washers to act like they're worn even though the reel is 7 years old. With a rating of 35 lbs of drag it should have no problem handling 7 to 10 lbs of drag. Now maybe I did something to cause that I don't know but I just spoke to someone from France that was using a Slammer III 8500 for 200 to 300lb Bluefin Tuna. The max drag on the 8500 is 50lbs. I also have this reel, the 8500 and he claimed the reel handled the 1st fight with his drag locked down to 25 to 30 lbs. After that it wasn't working as well handling that kind of pressure. I did the drag test on this reel and I noticed it was reaching it's max at around 30 lbs. So basically I'm finding out where these reels have their limitations. I'm not disappointed with these reels especially the Slammer but I just thought I'd have more use for the Spin Fisher 7500 before I bought it. The HT-100 and Dura drag is a decent system but I wouldn't recommend constant hard use of this drag system if you're expecting a fair amount of longevity.

[@SlotCityFishing]

No I would also make the argument if you are fighting that class of fish I would go with something g significantly more powerful like a saltiga or twin power. Thanks for the feedback.

[@eves08109]

That is exactly what I told the guy from France and I'm glad I was able to help with my experience.

[@pescabikeaventuras]

I think you don't know what gears are? there is wear, felt used with a lot of pressure, not the same as the new ones, carbon too, do you want to use a drag for 7 years and want it to be intact? Change the felts for new ones and be happy, boats wear out, our nerves, bones wear out, do you use a bike for 7 years without changing the brakes or chain? hugs from Brazil, horses

[@aco2518]

All I got from this was that the 6 has better gears and better sealing with a slightly inferior drag. And that you really really like your 5. I think saying one is vastly superior is just wrong. It depends heavily on what the fisherman values from the reel.

[@SlotCityFishing]

What about $ vs hype? They are very similar. I think you missed the point I was trying to make.

[@rubenromero4988]

After seeing this video You change my mind about the spinfisher v however my heart is set on the slammer! Can you please do a review on which is better. thank you

[@SlotCityFishing]

Ruben Romero yea bro I’ll do that.

[@rubenromero4988]

SlotCityFishing thank you

[@rubenromero4988]

So spinfisher or slammer?

[@Ranger-vv2jv]

I can't agree better, l have almost every reel you mentioned. One thing in fresh water the conflict ll, clash ll,is very light and durable reel 2500,4000,and 1 5000.l have 4 spinfishers.The 3500,2 4500 and 1 5500Vs. 1 think everyone is missing is the pursuit lll, it's great for the $ and will surprise you with a HT 100 drag..Rather have it then a BG,Shimano.But since l have 4 spinfishers v reels,and 8 pursuit 3 I'm set pretty good. For me it's PENN V, Pursuit lll .Fresh and salt covered.

[@SlotCityFishing]

Ranger 1780 Thanks for watching the vid bro if you aren’t already consider subscribing!

[@livenhfree]

Wayull... I have me a circa 1980 5500ss. Still kickin'! But I used it almost exclusively for surf and jetty. Striped bass and bluefish up here in New England. Time for an upgrade, and I was tossing between the Spinfisher VI and the Shimano Stradic FL. And max 4500 size, as I'm doing mostly inshore now. And no question, the V is a lot less coin than the VI. So now I have a dilemma (thanks fer nuthin'! JK!). To say nothing of selecting a good rod for a 4500 (St. Croix is a little pricey, but I'm up for other ideas). Great vids, just subscribed.

[@SlotCityFishing]

I have 2 st Croix mojo inshore rods and I really like them

[@wu3705]

I have 2 SSV5 8500 Penn Combos. Those things are tanks. Also have a few vintage Penn bait casting reels. At this time I don't have any reason to buy any new spinning reels as my SSV5's have never failed. A few in the 3500-4500 range may be in my future though. Something I can freshwater fish with and not feel like I am casting with a light pole :D

[@SlotCityFishing]

You still got the Vs?

[@wu3705]

@@SlotCityFishing yep

[@tisdale36]

Good video. Does this info hold up after 3 years. Of course now it seems harder to find the V. Also, I fish the Freeport, TX area, mostly inshore saltwater for specks, redfish and flounder, which Penn would suit me best? Or what reel of any brand is best. I am liking the Penn Spinfisher information I have seen. I have never used one yet, usually use Curados

[@SlotCityFishing]

For inshore you don’t need anything fancy or expensive. Even the cheapest penn is a great reel these days technology is so much better

[@SlotCityFishing]

I’d recommend something light that you wouldn’t be upset about losing. My opinion.

[@Al-oe8ib]

Totally agree, have 24 of the V series on charter boat. They have performed faultlessly for over 500 charters. Only problems have been bail arm bits, broken by novice anglers not releasing some line after winding it hard to the rod tip. Other charter boats supposedly upgraded, and were very disappointed with the V1, which is not as reliable

[@SlotCityFishing]

Yep!!!

[@fishing_in_blood]

what daimeter line u spool on it and how many meters? 4500series

[@SlotCityFishing]

I use 20lbs braid not sure diameter or how much fits it’s more than enough tho.

[@giorgishavgulidze6148]

Hey there i have watched some of your videos about penn reels, month ago a big fish took my rod with evrything to the sea, i could not run for it because i was in port area, i found my rod after a month on the shore 😅 penn spinfisher VI 5500 worked like new, if you want i can send you video for review

[@SlotCityFishing]

Dang nice

[@robertbrost7777]

Thanks for the honest review. Where can I find the Penn Spinfisher 5 for $69.98? At that price I'd be a buyer today! Thanks

[@SlotCityFishing]

That was a while back

[@selamatjailan7917]

Which penn model when we roll the line it light than other penn model

[@SlotCityFishing]

???

[@tyfishing3318]

How is that penn pursuit3 holding up? Is it the new budget reel from penn?

[@SlotCityFishing]

Ty Fishing zero probs still like new

[@Ranger-vv2jv]

I love the pursuit lll and it amazed me.But in all honesty l have a Spinfisher v 3500v, 4500LL, 4500,and 5500v. This reel gets it done,better then all my penn reels.I have a lot of Battles, Fierce, SS,Z,greenies ssm,ssg.But for fresh water l have a Clash ll,4000 and 2500.In salt not good but the weight, power, it's better for everything but large catfish.Sir you told the truth but I never go fishing without the 2 Clash' But I would not take the clash to the ocean. All 4 spinfishers would.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@andrewbilotta6735]

Hello great info. What Penn reel,you Fierce 3 or Spinfisher would match well with a Tsunami 2 Trophy 9ft. Thanks, Andy

[@SlotCityFishing]

Should be a good match thanks for watching and hope you subscribed

[@BJL0306]

Have two 8500 “work horses.” One is a V and one is VI. And I just bought two 10500 V. That’ll tell you something. Thanks for the info. What part of Sth Tx?

[@SlotCityFishing]

I was in corpus

[@MrHumbleShyam]

I have a doubt in my mind. I've ordered a spinfisher 5 - 10500 from ali express 2 days back. Is there a chance of getting duplicate product?

[@SlotCityFishing]

No idea man.

[@Palpac]

I’ve had 2 penn slammers for around 10 years? Not quite sure when I got them and pretty sure they are the of slammers. No gaskets at all, only just serviced the the other day for the first time as one took a drink. Both still like new but well used.

[@SlotCityFishing]

Yep people put way to much time and money into gear. The old stuff like 706z are killer reels. so good the remade them even! Thanks for your time if you arent already consider subbing to the channel!

[@Retwak]

whenever i decide to buy a penn i'll go to this channel to watch 😁

[@SlotCityFishing]

Nice dude!!!! What reels you end up getting?

[@hownowbrowntrouttasmania7389]

Hi there, I've been servicing my penn spinnfisher and slammer 3 and now they have some slight rotor back play as the roller bearing engages.Takle advisors had the same problem with his. Any advice will be great thank you from Jake.:)

[@SlotCityFishing]

I’m not a reel tech I wouldn’t know I just fish them

[@artbrigida7866]

Can you review the van staal vr 50 I think they're overrated I've had three of them all different sizes seems like every year they have to get serviced now they're telling me the vrs are not made to be dunked the new ones are sounds to me like van stalls trying to sell another product

[@SlotCityFishing]

I don’t have one sorry

[@peteranddorothybowles5428]

I think the point that you put about cost sais it all the 5 seems a lot cheaper and a hell of a lot of people out there don't need to spend the extra cash for the fishing they do I've spent 1000 s 0n reels when really I didn't need to the diving industry s the same You think more cash means better and it's not always true You were well worth listening to and I believe honest KEEP IT UP MR AMERICA DUDE

[@SlotCityFishing]

Thanks bro

[@SlotCityFishing]

There’s a lot of great new content on the channel you should check it out

[@jrollj]

What size penn spinfisher v model is good for a 12ft spinning rod 🤔🤔🤔

[@SlotCityFishing]

jrollj 6k or 8k

[@SlotCityFishing]

Depends on the target species.

[@jrollj]

@@SlotCityFishing ok thanks, l mainly fish for rockfish, croakers and blues in the bay

[@SlotCityFishing]

Where are you from. In Florida blues and croaker are small. You don’t need a 12’ rod or 6k for that. I don’t know what a rockfish is so prob not from the south huh?

[@jrollj]

@@SlotCityFishing I stay in the washington dc area,, everybody calls striped bass rockfish where I stay

[@derekcollins4306]

Is the surfblaster 3 a good surf reel

[@SlotCityFishing]

I’ve never used one and recently saw it. I’d like to try it. Thanks for watching! Hope you’re subscribed there’s a lot of great new content!

[@stepheno.2730]

After closely evaluating my ssv6500ll reels to the new ssvi6500ll, I have to agree with you. Although I did decide against a new VI, I did pull the trigger on a new Slammer 3 7500 size. That should help put the brakes on a big flathead and shake off a little river water/mud. Thanks for keeping it real brother. Tight lines. 🎣❤️ I do head out to port A/Rockport, TX usually once a year. Let’s get on some reds sometime.

[@SlotCityFishing]

CHS Miner Thanks for watching the vid bro if you aren’t already consider subscribing!

So instead of the Pursuit 3 should I just get the Spinfisher 5?

[@SlotCityFishing]

Pedro Ariano I would if there is any chance you’ll get the tee wet. If your bank fishing just save your money and get the pursuit.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@monkeyman4131]

Get what ya want, the Penn SSV and SSVI are the same. Tho the newer SSVI cost a bit more. Drag Washers are the same "H-T 100 tm. No Slammer Washers , not made. Tom Daytona Beach, FL.

[@peterstock1327]

All look great but look like toys compared to the early Spinfishers. 2nd and 3rd generation made in Philly. No solid BRASS main gears , tiny bearings as well - great video but 😎

[@mauricebrister6080]

What's the difference between a 850 and 8500

[@SlotCityFishing]

Nothing just different branding

[@Thefishingplumber]

Slammer 3 vs saragosa vs spinfisher 6 6500 for jetty action??!

[@SlotCityFishing]

I don’t have those reels

[@john.j16]

The only reel that I like as much as the spinfisher is the Diawa bg. It is a lot smoother than the spinfisher and a little lighter. It is also $77 for the 3000 size at Walmart. It is worth a try if you have never used one.

[@SlotCityFishing]

DV BamaFan you are the 2nd person to comment that I’m gonna pick one up and give it a shot. Thanks for the feed back bro.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@markmcgee6550]

Do you happen to know whether the spools are the same for the 5 and 6 (are they interchangeable)?

[@SlotCityFishing]

I don’t bro sorry.

[@markmcgee6550]

I have since found out, that they are NOT interchangeable.

[@robertbrost7777]

I see the 5 only comes in a 3500. Is that too big for us freshwater bass fishermen? Is this the reel that sells for $69.98? Thanks.

[@SlotCityFishing]

Robert Brost hey brother this vid was made a few years ago I’m not sure where you can find them here days and I would also say a 3500 spinfisher is a beast of a reel for freshwater. You’d be good with something way smaller and cheaper. The spinfisher is a saltwater reel.

[@Beyondthebreakers]

I caught sailfish and bunch of kings on spinfisher 5 5500 and it handled them easily

[@SlotCityFishing]

Beyond the breakers Thanks for watching the vid bro if you aren’t already consider subscribing!

[@wallace500001]

Once you get over a certain level the fishing is a fashion show. Spot on !

[@SlotCityFishing]

Truer words have never been spoken.

[@SlotCityFishing]

Check out our new vids bro. I still use all spinfisher Vs looks sweet

[@Palpac]

Cnc gears are cut from a solid block of metal in a cnc machine. A lot of gears are cast metal.

[@SlotCityFishing]

Palpac... yep.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@roelgarcia4249]

I have a 5 and I love it spinfisher 5 is my reel caught bullreds no problem still gonna use it no matter what good video.

[@SlotCityFishing]

Roel Garcia Thanks for watching the vid bro if you aren’t already consider subscribing!

[@caranx89]

hi!. well, you say that the new model is not as good as expected!.... Have you tried one of medium size as lethal80, spheros sw10k or cabo80? and big as lethal100? thanks!

[@SlotCityFishing]

caranx89 Thanks for watching the vid bro if you aren’t already consider subscribing!

[@thevernonposse]

Ill take a brass gear and aluminum gear over a cast zinc gear any day

[@SlotCityFishing]

Well…. Do it

[@Tight--LiNeZ]

I repair reels and have seen many V's with stripped gears, due to the grey "pot metal" they are made from. If you aren't after big fish, it won't matter, but if you want to catch Amberjacks (same family as Kingfish here in NZ), big sharks or tuna, I would go for the Vi, due to the gears. Take out the gear on a V, then compare it to a Vi. Pot metal makes me feel sick. It's like the stuff die-cast toy cars are made from. CNC brass gears will not easily strip and slip past each other eventually, like cheap pot metal gears will, when often put under big loads. It doesn't really matter with smaller reels (since the fish targeted don't have the horsepower), hence the SF 5500 and below use ali, not brass, and the 6500 and up use brass. I would personally say, if you want a large spinner for powerful fish and need the bigger sizes, go the Vi, but if you are after a smaller reel, the pot metal gears in the V's will be fine. The V do have better drags though, squeezing the spool from on top and below. Just get a Slammer III or even better, find a Torque 1 or 2 at a good price. A used one of them, is far better than a new SF V, Vi or Slammer III. If you are wondering my credentials, I have over 100 spinning reels of every make/price point, and service and repair them for a job. I don't like blowing my own horn, but when it comes to reels- I know my shit. Kia ora from NZ.

[@daddyramg]

Thanks for your info. Could you help me to choose between the spinfisher v and vi 4500 size please. I want it for 10 lbs bonitos and 25lb fish called "corvina". What should go better?

[@74monaro]

@@daddyramg If you are getting the 4500 in Liveliner model, don't get the Vi. I have had over 25 SSVi4500LLs returned due to the live liner system not working (which even when is working, is far too stiff on minimum tension setting, also have a clicker in live liner freespool model, which puts the fish off when running with bait in mouth). There isn't this issue with the 4500 Vi non live liner model, but I would still get the V over the Vi. It has a far better drag system, stronger bail arm, a nicer gold handle, and a nicer drag cap (cool little HT100 metal emblem vs being just spray painted on, on the Vi). The only benefit of the SSVi, is a slightly louder main spool clicker (negligible benefit), and it has a stronger gear material, but in the 4500 size this just doesn't matter. I have never seen a SSV with a broken or excessively worn gears (apart from totally abused reels, but that's the same with any poorly maintained reel). Also, when they say "sealed", they really aren't sealed like a Van Staal, Zeebas or Penn Torque, they are water resistant, put the SSVi isn't that much better than the SSV, and you should never wash down reels with water anyway. Just wipe them down with kitchen wet wipes after use. So everything considered I would get the SSV 4500, not the SSvi 4500. Just a more quality feeling, more solid, more reliable reel. And if you want the Liver liner model, DO NOT get the SSVi 4500 (it's only the 4500 size live liners that have issues, for some reason) Get the SSV4500LL. Like I said, the only real upgrade is the CNC gears, but they have down spec-ed the rest of the reel to maintain build vs profit margins. Get the SSV mate, I can feel fully confident/comfortable in suggesting the SSV, but not the SSVi. Besides, the reason the newer Spinfishers have such a good name, is from the V's reputation, not the Vi's. Answer: Get the SSV4500.

[@daddyramg]

@@74monaro thank you very much for your complete answer and tour knowledge, I appreciate that a lot. Greetings from Chile!

[@ioijiopjkiopjkp]

Dude have you even tried a VI? I have a V and VI and the VI drag is way smoother, way smoother gearing. You say you only care about how the reel feels while fishing yet you didn't try the VI??

[@SlotCityFishing]

I have a VI now and I still think the V is much better along with nearly everyone I know. My six now makes terrible noise and the gears grind. The v is still like new

[@ioijiopjkiopjkp]

@@SlotCityFishing that makes no sense at all considering the VI has more seals and way stronger gears

[@fishnhunt3488]

Cool video! Been trying to decide between the v and vi in the 55 series. The price difference is about $65 on Amazon. I think you helped me decide. Liked and subscribed! Thanks!!

[@SlotCityFishing]

Fish N Hunt Thanks for watching the vid bro if you aren’t already consider subscribing!

[@user-fl4wn9dn2c]

Is the slammer 3 quite a bit better ? it feels much smoother to me

[@SlotCityFishing]

Yea it is but it’s a lot heavier and more expensive

[@user-fl4wn9dn2c]

@@SlotCityFishing It is a good day if I am using any reel, need to buy a salt water reel for my 12' pole. Thinking Slamer 5 8500 or 10500 ? Mainl use is a beach pole.

[@deanmiller6177]

The PENN VI 6500 has CNC gears and the body is sealed and the PENN V does not have any of that.

[@SlotCityFishing]

Did you even watch the video? I show and explain all that?

[@drdimasadrianto]

Hi.. compare with daiwa bg magsealed ,which one better?

[@SlotCityFishing]

Dimas adrianto Thanks for watching the vid bro if you aren’t already consider subscribing!

[@mauricebrister6080]

And how can I buy one from you for $89

[@SlotCityFishing]

We don’t sell reels. Sorry I hope you are a subscriber.

[@mahzan1664]

Hi. Can u suggest for me between spinfisher V 4500 n 5500 for fishing gt

[@SlotCityFishing]

i wouldnt get either of these reels for that i would get a slammer 3 our a shimano saragosa. you need something with lots of stopping power. I use to fish for Ulua in hawaii (GT). Thanks for watching the video and subscribe to the channel we are always doin give aways and uploading new content. tight lines.

[@aleksandarpetkovic5734]

I have two v4500 and think that the handle is weak in comparation with the rest of the reel. I just have that feeling

[@SlotCityFishing]

…. Hmmmmmm what reels do you prefer?

[@AnglersLab]

thanks mate..but 6 looks more handsome..thanks for the explaination..good day

[@SlotCityFishing]

It looks good but I prefer the v

[@tellrich29]

Where abouts in South Texas?

[@SlotCityFishing]

tellrich29 I use to live in Corpus Christi

[@tellrich29]

SlotCityFishing I saw video from Trident Fishing at Bob Hall pier. Looks pretty bad.

[@SlotCityFishing]

I never fished there so many better places to fish in corpus

[@tellrich29]

SlotCityFishing Looking forward to seeing your vids. I live up 37N in the Alamo City and look forward to hitting the coast more often.

[@ommaka]

Whats your opinion about the slammer 3 ?!

[@SlotCityFishing]

Oussama Merebi I have one want me to do a video about it?

[@ommaka]

Yes please 👍👍

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@monkeyman4131]

They are nice ......tho the cost is HIGH ! Tho, if ya have the money ! Why not ! Tom Daytona Beach, FL.

[@youngblood8074]

How do you rate the 7500lc Penn.

[@SlotCityFishing]

I’ve never used it sorry

[@markdowney4029]

Terrible review. Main location of water ingress is the shaft . You did not address this area at all. V has no sealing here, VI does It seems you are not really knowledgable.

[@SlotCityFishing]

Thanks

[@john.j16]

I couldn’t agree more. I love the v and paid $84 for the 4000 combo and absolutely love it.

[@SlotCityFishing]

YEP YEP thanks for watching bro

[@odelaguila5003]

great, now can you talk about cheap and good braided line?

[@SlotCityFishing]

Magic O Thanks for watching the vid bro if you aren’t already consider subscribing!

[@Thebankfisher]

I talk closely with one of the Penn reps local in my area and trust me the only thing the 5 has over the 6 is they are cheap now ....glad you like your older 5 but it doesn't make it a better reel....

[@SlotCityFishing]

Let me ask you a question. What is the pen reps job.....? To sell you new reels. Of course he is gonna tell you that.

[@Thebankfisher]

@@SlotCityFishing both reels are good but the 6 is an obvious improvement

[@camboviet316]

Wish I saw this before I bought the spinfisher 6 5500. Smh

[@daddyramg]

You think v is better than vi?

[@camboviet316]

@@daddyramg I have the spinfisher 6 is cheaper made.

[@SlotCityFishing]

All good man that’s still a great reel I have one and love it too

[@wanzhaf932]

"solid alloy handle" your reel handle please...rather than pin jointed...small improvement but major on 2020 and years to come....

[@SlotCityFishing]

not a bad idea bro. hopefully @pennfishing will see your comment. thanks for watching and tight lines. i hope you are a subscriber to the channel we have a big 10k sub giveaway coming up and we did a battle 3 review that we are giving away as well.

[@danielzanders5191]

I have a spin fisher 6 and I’ve never had a problem with it

[@SlotCityFishing]

Great reels. Hope you subscribed to the channel

[@danielzanders5191]

@@SlotCityFishing I sure did

[@beachdude562]

i think so too and never even seen one or held one just from looking it up i also have different penn reels , great video.

[@SlotCityFishing]

beachdude562 Thanks for watching the vid bro if you aren’t already consider subscribing!

[@SlotCityFishing]

That down vote somone has buyers remorse.

[@rollin_with_romero]

HAHAHA!! They dont wanna talk about it tho......

[@SlotCityFishing]

Nah.

[@nirknass]

Thanks man, glad I bought the V model.

I might get the 3500 and the 8500! The 3500 for small fish and the 8500 for the big fish!

[@SlotCityFishing]

Pedro Ariano yea man. I prefer the 6k size reels for surf fishing. More manageable. The 8k is very big.

@@SlotCityFishing Thanks is because I'm new in the fishing world, so I thought that the Penn Pursuit 3 was a bad low quality reel.

[@SlotCityFishing]

Not at all man. Don’t let people tell you otherwise man. Lots a snobs in the fishing world.

[@Beyondthebreakers]

Unless you fish for big sharks from surf, you don't need 8500 reel.

[@BrandonBarton13]

I disagree. Cnc gears, higher waterproof rating and drop in weight is more important than the 5lbs of drag that they reduced. Close out sale price of the spinfisher v is a great deal though but wont be available forever. 🤙 tight lines

[@SlotCityFishing]

Emerald Coast Kayak Fishing thanks for the feedback brotha. Tight lines. Maybe we can meet up in pcola sometime and rip some lips.

[@FishWithBish]

Iv'e found this sometimes they change tackle without keeping the quality!!!!

[@SlotCityFishing]

Fish With Bish Thanks for watching the vid bro if you aren’t already consider subscribing!

[@fagnerbarros8252]

Nice video ,I have one no complains! Very good reel for under $100

[@SlotCityFishing]

Thanks bro if you arent already consider subbing to the channel we are doin a giveaway here soon! Im goin to do a penn fierce 3 review here soon too

[@morales2678]

2500 is the reason to buy

[@SlotCityFishing]

MMO GAMING you know a 2500 and a 3k are the same size right. Just different spools.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@monkeyman4131]

I bought a 2500SSVI when they first came out ,and it's GREAT ! Tom Daytona Beach FL.

[@alifahrudin3073]

5 or 6 . Spinfisher is Rhino rell .. salam dari Indonesia . 🙏

[@SlotCityFishing]

Nice what reel you gotcha

[@andrewmorke]

Sorry but you're mistaken.

[@SlotCityFishing]

Aight

[@Jasminelovesthenumder7073]

Thanks for the info, good video,

[@SlotCityFishing]

Glad it was helpful!

[@ronmb81]

The V is more or less on par to the VI in price in Australia, crazy

[@SlotCityFishing]

ronmb81 yea it’s an incredible reel

[@ronmb81]

@@SlotCityFishing hey mate, im looking to buy my first Penn. I want use it for rock/surf fishing on a 10'6" Rod. Would you recommend 5500 or 6500? or would long cast model be my choice?

[@kimiyahferreira6808]

Thanks for the eye opener.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@monkeyman4131]

Not every thing was true, there is " NO SLAMER DRAG " All are " H-T 100, drag washers on the Penn SS, SSV, SSVI, models. Tom, Daytona Beach , FL.

[@SlotCityFishing]

@@monkeyman4131 i agree its the same washers different mechanical design employing them.

[@bennyrosado5402]

Thank you for your display of information. It saved me time from having to do the research !

[@SlotCityFishing]

+benny rosado you are very welcome dude. Thanks for watching.

[@Bigbitefish]

Power reel brooo

[@SlotCityFishing]

Yeeee

[@jhonmukhlis5173]

Slotcityfishing better where is the reel spinfisher v or spinfisher vi?

[@SlotCityFishing]

Jhon Mukhlis Thanks for watching the vid bro if you aren’t already consider subscribing!

[@japinoybettajapan]

Thanks for great info boss

[@SlotCityFishing]

No prob hope you subscribed

[@japinoybettajapan]

@@SlotCityFishing I already did

[@dalehilltopfarm]

Always honest! Thanks!

[@SlotCityFishing]

Thanks dale

[@iancampbell1494]

You have an opinion on the Shimano oc baitfeeder? Looking to buy one but then I found the Spinfisher and now I’m torn

[@SlotCityFishing]

Ian Campbell I don’t have enough use on one to give you an opinion. Wish I could help.

[@iancampbell1494]

SlotCityFishing no problem , seems to be uncommon for people to use, any opinion on baitfeeder / liveliners in general? Is it a gimmick?

[@SlotCityFishing]

Live liners are my favorite I have 5 of them.

[@iancampbell1494]

SlotCityFishing the fierce or the Spinfisher

[@SlotCityFishing]

We have 5 fierce and 1 spinfisher all live liners.

[@tsuyang4173]

got one for black friday (2017) and i like it. good to know these facts.

[@SlotCityFishing]

good deal man! they are great reels both of them really. I just prefer the 5.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@reelwickedrods7147]

Good review. Thank you for the information. I'll pass this info onto my clients.

[@SlotCityFishing]

Lori Baird thanks Lori.

[@SC-dw3jz]

"Monster fish". Nah bruh. I'd rather have machined gears that aren't shitty zinc for actual monster game, like alligators. The 6 is an upgrade. And amazon has the 6 8500 combo for only $14 more than the 5 8500 combo.

[@SlotCityFishing]

S C alligators?

[@SC-dw3jz]

@@SlotCityFishing Yep. In Florida the way you catch gators is either a baited wooden peg or a treble hook.

[@BigTee-lp7qu]

Jesse, Not much good to say about review as you missed a lot of V vs VI changes... body screws moved outside of seal etc. and BTW a reviews and opinions are good for us reviewers looking for products but your lighting and videos and speech could use a bit of polishing and I'm just an old Tennessee hillbilly living in Bama these days, just saying... check out Tackle Advisors channel for production tips...

[@SlotCityFishing]

T. Long thanks for the feedback brother. The channel has developed a lot since then. We do appreciate the feedback, I did over look the screws as well you aren’t the first person to mention that. Tight lines.

[@THEBLACKANARCHIST]

U like the daiwa BG

[@SlotCityFishing]

FUCK YOUR FEELINGS BITCHES I’ll be honest with you man never used it. Would you like us to review one? I’ll try to pick one up.

[@THEBLACKANARCHIST]

@@SlotCityFishing yes .they say outside the Penn spinfisher it's the best bang for your buck.it has a massive main gear

[@SlotCityFishing]

I’ll try to pick one up and use it.

[@THEBLACKANARCHIST]

@@SlotCityFishing thx

[@SlotCityFishing]

Nah bro thank you for watchin man! I’ll try to make that happen.

[@theblake5356]

It’s not a matter of opinion. Better, stronger/more durable gear set.... better bearings, completely sealed lighter body, etc. The newer drag system on the VI is what ALL Penn reels are going to. The Spinfisher VI is by far and away superior to the V. It’s not even close. This is really on the verge of click-bait.... I can’t believe that you honestly believe what you’re saying here. You have a decent channel, no need for cheap views.

[@SlotCityFishing]

The Blake all that maybe true (I don’t think so) but you missed the whole concept of the video. I’ve had that reel goin on 4 years, never had a single issue with it, submerged it multiple times (still completely dry) has higher drag, and ive landed tons of monster fish on it. At what point is better necessary? I’ll save the money and use the cheaper (better value) reel... while you’re at it send us your old ones. Think about this no reels where Cnc geared or ipx 5 rated until the last few years. Cheers man. We can agree to disagree what’s really important is catchin fish.

[@theblake5356]

Gary Dodgson You should open your mouth a little wider when you speak.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@rollin_with_romero]

Wow crazy !! Glad im still running the SF V

[@SlotCityFishing]

Reel_life_Roland yea man.

[@nasiasteel9105]

He's absolutely right

[@SlotCityFishing]

Thanks

[@christianfortun4275]

Penn spinfisher vi VS Penn Battle 3 ?

[@THEBLACKANARCHIST]

Thanks so much brother

[@SlotCityFishing]

FUCK YOUR FEELINGS BITCHES no prob dude.

[@SlotCityFishing]

Thanks for watching the vid bro if you aren’t already consider subscribing!

[@rustydriver5697]

bone dry and never serviced or greased...........you need help

[@SlotCityFishing]

it was full of grease bro hah. I didnt even need to clean it. it was like new. thanks for the comments. tight lines.

[@FISHH00KS]

Tell the time don't build a watch.

[@SlotCityFishing]

Ten Millimeter clever.