SPRINTER SRS Airbag light fix

[@mecanictransmision]

I have both airbag activated, can i put it in the place where the airbag plug? In the steering wheel?

[@ZEIMISJZ]

Probably yes

[@mecanictransmision]

@@ZEIMISJZ thanks a lot! I have 3 ohm resist. Will it works? Im in peru

[@mecanictransmision]

Wath happens if I use 3.0 ohm?

[@ZEIMISJZ]

You not gonna be able to turn off airbag light

[@walterjameson3896]

Great video. Can you advise me on your Autocom software, where you got it please?. I have an SRS fault on my middle seat which keeps activating when the wire is touched underneath. But i cannot reset the SRS code without having to bring to garage.

[@ZEIMISJZ]

I got it on ebay 5 years ago.

[@RobloxCraftStream]

Information is very good

[@ZEIMISJZ]

Thanks

[@griniovdumitru5808]

Спасибо За видос. Программу диагностики можно установить на любой Лаптоп?

[@ZEIMISJZ]

Yes on any PC

[@griniovdumitru5808]

@@ZEIMISJZ Где взять эту программу?

[@ZEIMISJZ]

@@griniovdumitru5808 € 69,58 45%OFF | Automotive Diagnostic Software delphis keygen 2020.23 ds150e double board autocoms for truck scanner tool diagnostic tool 2017R3 a.aliexpress.com/_vosr1c

[@bluemackay]

Hi can you tell me what obd or programme you are using please?

[@ZEIMISJZ]

I was using AutoCom

[@vladislavmitev7286]

hi i have the same problem but in this cable box i have 3 cables not 2 my question is where to put the resistor tnx

[@ZEIMISJZ]

on the yellow cable

[@vladislavmitev7286]

@@ZEIMISJZ yellow and which other tnx again

[@ZEIMISJZ]

I think only yellow

[@vladislavmitev7286]

@@ZEIMISJZ so the yellow cable is important no matter other side?

[@ambientsounds1416]

@@ZEIMISJZ Vladislav is saying that our connector has 3 wires, but the resistor only has 2. Which colour wires need to be connected to the resistor please?

[@englishkernigit8294]

Excellent

[@stu1c]

Hi, is it possible just to bridge those 2 wires together instead of using a resistor? Thanks

[@ZEIMISJZ]

No

[@alqui20000]

Thank you for sharing.

[@TheRazvancristian]

Hi, I have an error in the board "SRS, restraint system faulty drive to worshop", this error appeared after I moved the seat further forward or further back, what could I do? (at my Mercedes benz a class A170, 2005 oil 1.7)

[@paulbucknall2435]

You have pulled the wires from the airbag connector. Just re fit

[@МАСТЕР05-ру]

Доброго времени суток. Здравствуй дружище здоровья тебе и твоим близким . Это Уллубий. Всех благ тебе .

[@lucheteojete]

If you just put the resistance, will the SRS light be out? Or you must erase it with the scanner? The guy who use my sprinter just ripped the sensor from the seat belt...

[@ZEIMISJZ]

No you need to erase Airbag error in ECU

[@3bullzgaming442]

Only if you turn the ignition on. If you swap it over and change it before turning the ignition on the error won't appear

[@walter9495]

Молодцом