VAN CONVERSION SRS light fix

[@philliplewis7689]

Thank you! It worked on the Vito 114 2016 model. Pulled the seatbelt out and left it connected as suggested. Save loads of headache and money.

[@SuperClotted]

For NCV3 906 driver seat replacement can use a 100 ohm resistor to resolve SRS warning [3.3 ohm for passenger seat], then use Autel AP200 to clear error code

[@stevenfrost4188]

Spot on fix thanks for the info saved me a lot of money👍👍

[@KevinBroom-p6x]

I have a mercedes benz sprinter 2012 i have the srs light on.put on the dionostic at the garage and they say i need a new unit .srs unit replacement .and also it on my dashboard it sed the same thing as your mercedes .

[@nuklearpuppy]

I don’t have to yellow clip on my sprinter van . Will this work if I connect the wires to the resistor using crimps ?

[@MrMeltedwellies]

not sure

[@jumabioya2235]

It sure wold help if you told where to buy this device on eBay !!! Also what is it called?

[@paulwhite256]

Do you have to disconnect the battery

[@MrMeltedwellies]

i didn't

[@mrhbarker]

Love the video but can't see a link...

[@bugtec]

Good job! TKS for share.

[@stefanstroie]

I have a question. If the airbag will pop up even when nobody is on the seat? Or the airbag will pop up only when someone is on the chair.

[@MrMeltedwellies]

only if in the seat as i think its a pressure switch

[@stefanstroie]

@@MrMeltedwellies thank you for your response. How can I check if the pressure switch is good. Can a tester indicate that the switch is good? If the switch is good then this trick with that device would solve my problem.

[@Profesyoneldroneçekimi]

2013 model sprinter aracım var ve srs ağrizasini kesemiyorum bu alet ise tararmi sizce

[@unkelartgarf3792]

You don't need that piece of garbage off eBay. It works with a 10p resister (2.2ohm).

[@especiallyforzozsings]

2,2 ohm, are you sure ? I saw a tutorial where the guy used a 3,3 ohm resistor (on a Sprinter though...) and a seller on Ebay told me that 2,7 and 3,3 ohm are the best seller resistor. Thank you for your response. Where did you get your resistor, please?

[@alanjohncattanach]

Link does not work, need something for 2012 vito113

[@michaelgraves5005]

I can’t find the eBay link ? Any help please

[@TheRazvancristian]

Hi, I have an error in the board "SRS, restraint system faulty drive to worshop", this error appeared after I moved the seat further forward or further back, what could I do? (at my Mercedes benz a class A170, 2005 oil 1.7)

[@MrMeltedwellies]

check you haven't pulled the wire apart you can get them reset at local garage

[@ejdoney]

Hi there, I am having the exact same problem and van has failed the MOT. I cannot find the product in the link you've put. Where on ebay did you get this resistor? Thank you

[@mauromaoddi8202]

Hi, im having the same problem on my vito. As i put new cover seats probably I unplugged from somewhere the yellow little plug. I'm wondering if you know where it should be plugged. Many thanks

[@andylaauk]

Resistors work either way.

[@gordondavies8970]

Hi. Can you give me the address of the supplier. Got the same issue with my Iveco daily.

[@karldingbat]

That srs light should of gone off on its own once resister connected, after 30 seconds, if not you have other restraint faults and possible airbag issues shouldnt need dtc reset. Mine was the same but i had passenger airbag malfunction.

[@tahransaeed1617]

Sand send me the name please

[@hemiv8949]

You keep saying RSR surely it's SRS