SPWM 3 Phase Inverter Step by Step Simulation on Simulink

[@gadegroof]

Thank you so much. I am investing my knowledge more in electrical drives because of the zero-emission goals in the further. I gonna try to link it with a physical hydraulic model.

[@TheUrbanScholar]

All the very best Albert!

[@gadegroof]

@@TheUrbanScholar May I ask you something? I am very happy with the model, but I cannot get it linked to a hydraulic pump/powerpack model. Do you have a tip as to where I can find out how to connect these models?

[@shubhranshuranjansharma4892]

Great sir ... Please also make one vedio on fault tolerant of inverter. If any leg of inverter get damaged,then how it work . Thanks

[@bluemuhendis]

Thank you for your help

[@SantoshYadav-Bgm]

Do video on field oriented control of induction motor drive Sir. ..

[@TheUrbanScholar]

Sure we'll do it 👍Stay tuned 😉

[@ani.tha13]

What will be the output AC voltage when 200 V DC is inverted ?

[@frf3ed439]

Hello sir, do you mind teaching me how do make goto to from. Thanks

[@ankitasharma5803]

I am not able to find not gate in my matlab version wat should i do?

[@pratyushdas]

How to fine tune it more to resemble sine waves?

[@shashvatmukatiwala4494]

sir, this reading which you get in the scope.... is it the phase voltage or line voltage?

[@TheUrbanScholar]

Anything measured between line to ground is phase and line to line Is line voltage, scope reading is phase voltage

[@yanshengsoh6215]

What is the use of triangle generator

[@ahmaddeab_5415]

You are amazing Thank you so much ❤🌸❤ I wish you do simulation about open ended winding induction motor drive

[@TheUrbanScholar]

You're most welcome!, we'll do the Simulation in future for sure 😁 Pls share our channel with your friends as well,they will also find it very useful like you did 😉

[@ahmaddeab_5415]

@@TheUrbanScholar I will shar the chanal I'm doing master degree in open ended winding induction motor drive Do you know haw to simulate it❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

[@hhcruz1999]

Sir I wanted to simulate a single phase inverter with at 500W, 12V. So the output current must be close to 41.67 Ampere. But my simulink block generates close to 4A at 12V. That's a total power of 48W. Can you suggest methods to increase the power rating on simulink. I have used 12V 65Ah battery as the source.

[@TheUrbanScholar]

Hope you're doing well! Current drawn depends on the load. You can represent loads in multiple ways like in terms of ohms or interms of watts, I'd suggest you to represent in terms of watts so that uou get W/V current

[@hhcruz1999]

@@TheUrbanScholar It's not working sir. i used series rlc branch at different ohms. I used series rlc load at 500W active power. There is no useful change.

[@TheUrbanScholar]

Could you mail us?

[@mahdeenafis6937]

Can you please make a model of SVPWM

[@yakubmakandar4111]

Value of R, L, C and Value of DC source?

[@abhishekmaji7555]

I cant find normal NOT gate. only CMOS NOT is there. Matlab 2013 . pls help

[@bechainvines3372]

Hello, I want to ask something. Can you please tell me how can I give inverter output to my simulink model?? Please replay ASAP my fyp become stuck because of this. Thanks

[@TheUrbanScholar]

I didn't quite understand the issue. Maybe you can tell your problem at [e-mail]

[@wickbron8964]

Hi can I know your email? I want to ask regarding of three phase SPWM inverter

[@TheUrbanScholar]

Mail us at [e-mail]

[@wickbron8964]

@@TheUrbanScholar hi have u received my email?