Spyder Auto How to Install: 2007-2013 Chevrolet Silverado Headlight (PRO-YD-CS07-HL-BK)

PRO-YD-CS07-HL-BK (Black Housing w/ Clear Lens)
This video demonstrates how to install a set of Spyder Auto This video demonstrates how to install a set of Spyder Auto 2007-2013 Chevrolet Silverado Headlight w/ Black Housing. This complete how-to walk through tutorial guide you through the complete install process from start to finish and offers helpful tips throughout to facilitate a successful installation.. This complete how-to walk through tutorial guide you through the complete install process from start to finish and offers helpful tips throughout to facilitate a successful installation.

[@jessicamaddox9814]

This tutorial should show you which wires the guy pre tapped into. This was the whole reason I watched the video and he does even show you what goes where.

[@spyderauto]

Sorry, you need to use a voltmeter and figure out which ones are the correct wires to tap into.

[@whisperproductions9880]

@@spyderauto you should show it for this specific truck like Jessica said. What a waste of time.. your videos suck.

[@kyleatlas1]

What method do I use to tap into the main harness?

[@whisperproductions9880]

@@kyleatlas1 run the positives of each running light to a "ignition on only" fuse on the fuse box and add a fuse also..

[@dee3368]

You want to tap into the parking light. That is the harness that goes to your marker lights in your headlight. but you'll definitely need a voltmeter to check . some Vehicles it's the center wire of the marker light harness some Vehicles it's the left wire the ground is always black so you have two wires you need to test when you find the parking light wire it will be a constant 12 volts it will fluctuate slightly the directional wire will increase and decrease in voltage rapidly you do not want to tap into that one

[@stevenahm3044]

Bought this kit. I have a lifted truck and will need to adjust the headlights. You do not demonstrate how to transfer the adjustment mechanism or how to properly adjust lights. Also, do u include the electrical components or will we need to make a run to the auto parts store? Please advise.

[@leticiasoto5020]

Can u break down to me how to connect the led lights. The black and white and res wires to the connectors

[@johnrojas8366]

Which color wire is the parking wire on the main harness?

[@LetsRVtv]

Did they ever answer your question? I'm doing the installation now but they didn't show a close up of the wires.

[@oreothes1974]

@@LetsRVtv did you ever find out?

[@Fishnfreak]

I purchased these 2 yrs ago. Taken to 3 mechanics. No one can figure out how to properly wire these. Called the company and talked to product specialist, still, couldn’t find the problem as to why my low beam keeps shutting off. HIGHLY NOT RECOMMENDED. Spend more money and get something better quality.

[@R.J.333]

Just installed mine and the Halos nor the Leds work.. They do work connected straight to 12v so they are ok. Could it have something to do with my 2008 Z-71 having DRL's with auto headlight switch ????????

[@jaydenstoddard6099]

Mine are 3 white and 3 black no reds. Would I still do the same?

[@rodneyhendrix93]

Great example

[@MrFreakfortatt]

My lowbeam driver side quit working its not the buld what could the problem be?

[@hectorvides2741]

Where does your ground go????

[@ernestvaldes8218]

Can I get some advice. I installed these on a 08. The low and high were easy direct plug. I wired the LED and halos to the ignition. Those work great. The issue is the low and possibly the high are very dim. Honestly worse then my factory.

[@jmdpo17]

From what I've found they are dim no matter what.. Did you go w another light brand?

[@raymondchen6720]

Make you make a vid on installing low beams?

[@asaparsons5746]

You know I bought I said headlights and tail lights from you guys and are you gave me was the headlight where are the tail lights

[@rickyalmaguer1191]

I have the 5083524 mode that I want the led lights to be my drl. How do I wire that so that the headlight is not the drl?

[@spyderauto]

Sorry, they are not meant to be used as DRL. They are to be tapped into your parking lights.

[@jeremyrobinson5312]

What about the ballast and hid bulb that came with the kit also??

[@spyderauto]

We do not sell our lights with HID kits. HID and LED kits will void the warranty. Some sellers may choose to sell the lights with such kits, but please note that using such kit would void the warranty.

[@Scorpio_Slayer]

Will these projectors work with HID? And would HID melt this housing?

[@crazyangel1128]

What about ccfl halo

[@tobylee3963]

What about adjusting the Halos how do you adjust the lights

[@andresramirez2844]

Can i put led bulbs or hid ?

[@fernandom.3174]

Hid !

[@jessemurray1757]

I was going to buy this but without instructions on how to wire, yea no way.

[@ricksanchez7999]

Best aftermarket headlights. Don’t get spec D they don’t have a huge quality control... bought spec d before and always faulty or cutoffsheild is upside down... blinding people.

[@speakerboxexpert]

do yourself a favor and dont use T-taps ever. Worse type of connection you could make and its just lazy if you ask me. other than that good video

[@maxbluntz6145]

what is part number for replacing low beam bulb

[@tommyeastberg123]

H1

[@TheTexan_87]

Not all H1 bulbs fit though..Im having a hard time finding the right size of H1...its annoying

[@tommyeastberg123]

@@TheTexan_87 I have auxbeam h1 in mine.

[@TheTexan_87]

@@tommyeastberg123 The fan housing lets it fit in yours? I have a 2011 Silverado and the fan housing wont fit because of a metal frame thats in the way

[@tommyeastberg123]

@@TheTexan_87 yes they are very tight but they fit in my 08

[@larryogkushnoriega7776]

Everyone know why the dislikes

[@jameslovitt994]

My Brother in Law bought an '07 Silverado with these on it, absolute junk.

[@jackmarlin3666]

Not a very good video, dont care for the music either. I have a 2013 and the wires do not plug in the way he shows. I bought the Spyder Headlights with the C halo.

[@l8tapex]

Video will save you time and is a cool service! Be aware! This isnt a complete plug and play. Go here : kzbin.info/www/bejne/mYrSlWyHmLN_r6s They dont tell you what color wire is the + and which color is the negative even specifically to this year truck in this video . It is intentional, So you will have to get a meter , learn how to penetrate each wire until your figure out the lead needed.

[@Fishnfreak]

Yea and terrible job explaining how to wire these buddy, thanks for nothing

[@jonathandutton1992]

Worst ever