Bro okay so I'm 15 and I REALLY want to restore my great grandpa's 1985 GMC Sierra and the fuel pump is what I need thank you a lot I'm ready to do this now! 😄
@noahhamilton90282 жыл бұрын
Hope you did it man :)
@SaraB16865 жыл бұрын
Thanks for the video. Makes me feel more confident about replacing the pump in my '75 Chevy.
@Pablo-gw5lu3 жыл бұрын
I got a 75 Chevy too
@marinervalley15883 ай бұрын
Same
@jaydurych2 жыл бұрын
It was very helpful to show all the needed tools at the start of the video. Thanks !
@1hernandez783 жыл бұрын
The less snap on tools u have the better parts u have for your cars😁👍
@Mrgrenades10004 жыл бұрын
Dude thank you so much, I'm doing my first real restoration with my 65 c10 and this just saved me a big headache.
@jerryjimenez82482 жыл бұрын
Just got a 1980 c20 how’s your project
@justnature135 Жыл бұрын
How's ur project ??
@orionburton38294 жыл бұрын
Thanks for the push rod shoot, very clear info. I'll change my self fuel pump of my chevy 86.
@FrenlawnLawn3 ай бұрын
I was having trouble didn't know you had to put your push the push rod
@obudoken2 жыл бұрын
I have a square body with a v6 engine. I have no room to work on my fuel pump like you have. I envy how how much room you have.
@WTFalcor4 жыл бұрын
Just a future truck to holding that pushrod, theres a 9/16 bolt just behind the fuel pump on the front of the block,i think its like an oil plug. take that out and put in a longer bolt untill it just snugs on that pushrod. do this before you remove the pump so you know its in its perfect position. then remove the pump and replace. Saves you time from messing with the pliers
@joshuataylor24734 жыл бұрын
You can use one of the bolts that holds the pump on too. Take one of pump bolts out and leave the other tight remove the closest bolt to the pump from front of the block. Put pump bolt in till it's snug. Remove pump and reverse steps for install. If rod falls anyway just push back up with finger and tighten bolt untill rod stays in place
@MrSFSTUDIOS Жыл бұрын
The pump came with two gaskets because there is a removable plate bolted to the engine block. One gasket is for that, the other is for the pump.
@prestonblaineroddam79866 жыл бұрын
Do more vids yo , you are doing amazing
@smokeydabeecharlescoleman83653 жыл бұрын
Nice try. Just the deep well socket to do the job with a wrench. You forgot to tell them to plug the fuel lines with a bolt to prevent the tank from draining. You only use one gasket, the other is a spare. Often two or more gaskets are sent incase the same pump fits different blocks.Instead of a saws all blade, use a hacksaw blade. You cross threaded that last fitting .It will leak fuel.
@MrChevrolet19715 жыл бұрын
Hello from Germany. May I ask you something? I drive a c10 Stepside from 1987. Engine 5700. Fuel injection. Since a couple of months the engine goes of while I drive. Only when driving less then 30mph . For example, if I go to an intersection and go off the gas. The engine then restarts again directly. I have already changed the idle air and imap. No improvement. You have any ideas? Maybe also the fuel pump? Thanks a lot for your help. Ciao Pino
@JinjuKim-j5e9 ай бұрын
Nice u just made this look easy 😂 now ima waste 9 hours of my life trying to do what u did 😂😂😂
@lucerog13743 жыл бұрын
Hi just seen yur video. My question is do I have to lube or something the gaskets or can I use the bolts like u did?
@MrTarkus0075 жыл бұрын
i would of liked to have seen to see how you installed the pump
@levilucyshyn9395 жыл бұрын
nick diaz I lifted up the push rod with the bent saw blade and it slide in
@terrywatkins44984 жыл бұрын
Peach Productions what if i dont have a saw blade?
@christined44522 жыл бұрын
is the middle tube connector a vent ? thank you
@bongripper10842 жыл бұрын
So did it start
@ryangillis96755 жыл бұрын
I am replacing the pump on my 86 C20 and the new pump comes with a spacer plate that goes between the new pump and the block. Any idea what that spacer plate is for? I have never seen one before? Thanks
@geecarrr23275 жыл бұрын
Spacer plate blocks off oil him when replacing it leave the plate bolts a little lose then put the pump in and line it all up helps out alot annnnd the push Rd stayed jn place for me i plunged the inserted end into valvoline heavy greas left glob on the tip and it stayed veefy well over night actually lol
@dirtyrafa4 жыл бұрын
Thanks for the video! I noticed that the replacement has 3 ports, my previous fuel pump only had 2. What's the purpose of the third? What did you do to it?
@senditkenny78384 жыл бұрын
1 Is a line that gives you gas from tank, smaller line is return line back to gas tank, 3rd metal line goes to carb. Older ones I believe never had a return line to the gas tank.
@c.mcadam.69113 жыл бұрын
I am pretty sure it is for a 2 fuel tank truck
@angelasanders262 жыл бұрын
What did you do for gasket
@jordanparker83594 жыл бұрын
Did it work??
@almor4575 жыл бұрын
I just replace my fuel pump still dont get fuel to th carburetor what u think is???
@levilucyshyn9395 жыл бұрын
Al Mor take the fuel like off from the pump to carb and blow it out. If that didn’t work, put a rubber line on the pump and put the other end in a jerry can and try. If that works then that means a fuel like from the tanks to the pump is plugged
@DirtyOperations5 жыл бұрын
What was the problem? Was it not receiving gas?
@levilucyshyn9395 жыл бұрын
DirtyOperations my problem was that the fuel lines from the tanks to line were plugged with rust
@daveklotter12725 жыл бұрын
Never use double gaskets !
@levilucyshyn9395 жыл бұрын
ed rettolk noted!
@geecarrr23275 жыл бұрын
Ya was without an airpukp in the way
@tannermedernach71416 жыл бұрын
Post more
@bolt_nation94286 жыл бұрын
Yah yet
@marktremper85183 жыл бұрын
I want a big block
@Pablo-gw5lu3 жыл бұрын
And I want mpg
@bolt_voiceless29646 жыл бұрын
Yee ha
@CommanderKlag6 жыл бұрын
YOU DID NOT SHOW THE ACTUAL INSTALL. Why not ? Does your procedures not work so good ? My guess is you are pretending :) Or needed to clean off the blood from your knuckles too often.
@levilucyshyn9396 жыл бұрын
Well you clearly didn’t watch the whole video. I can only use one hand while filming with my IPHONE. If you watched the whole video you’ll know I explained how to get the push rod up. This is a easy job and maybe if you spent less time commenting how to hold your hand while you do a easy job you’d learn how to it yourself.
@JohnnyMacalvee-cf7et5 жыл бұрын
@@levilucyshyn939 Commander Klag is a high octane troll. Pay no mind.