How to make a Weather monitoring system using the Nodemcu ESP8266 board and the New Blynk app

[@sritu_hobby]

Code and circuit diagram links in the description.

[@karthikgamers7069]

Noo sir it rally works

[@OnlyWork-v6g]

I am doing this project but the temperature and humidity sensor is not showing any results . i have done the connections properly as shown in the video . rain sensor , ldr sensor and pressure sensor is working correctly . please suggest what to do .

[@golamkabir1160]

thanks now i can make a roverthat monitors all these + soil mosture😊

[@topuhr1057]

Sir i couldn’t connect wifi with blynk... No problem in code.. The code was uploading but didn’t get any ip in serial monitor that i was used for connecting wifi with nodemcu...what would i do for this please help me!

[@aegchannel7369]

Hi I tried the raindrops module, but the rain sensor doesn't detect water, it rises when i touch it.

[@arif2xyz]

If i want to add fir sensor to this project, can you please provide the info, it will be helpful.

[@HarshithaKadiyala]

Which bread board did you use?? Can you tell me.

[@sritu_hobby]

830

[@abelvarghese4000]

Liquid crystal i2c library is not supporting can you help me

[@victorhurtarte7563]

My rain sensor gives a reading of 100. I check and recheck without success..any advice on this?

[@sritu_hobby]

It's normal.

[@victorhurtarte7563]

@@sritu_hobby , thakns for answer. But....when it is no rains reads 100, and when start rainings read a lesser value, Is that normal?..thanks again!

[@Arnay111]

Awesome project

[@sritu_hobby]

Thank you

[@amrtechandgaming9396]

Which version of Arduino ide you used sir? Because i can't to it with latest version(1.8.18) showing lot of errors

[@informativefuntechz6838]

Hlo sir, I had tried this project and everything is running perfectly and it also showing reading in the app but jo lcd display hai uspe reading hi show nahi ho raha hai kuch bhi jaise aapke me show ho raha hai instead phone me accurate readings aa rahi hai sir plz help me with this lcd problem

[@aegchannel7369]

Hi, will it work if I dont have the LED Screen?

[@BeckyG77]

How many pin Breadboard are you using? 830 or 840?

[@Niv888]

sir i have question for you, If I don't use jumper cables can I still run this project?

[@Niv888]

i mean get test with clip jumpers

[@mun5660]

Tried doing this project but with a LM35, LDR and gas sensor using an esp-01 wifi module.. The readings for LDR and gas sensor are correct but Lm35 is not showing correct temperature. If I just use the Lm35 only then it shows correct answer but with other sensors in circuit it shows wrong answer. What us the problem please help?

[@sampreethnagabandi3543]

what is the external 5v power source that is used ?

[@sritu_hobby]

Not enough power

[@Misqueen2023]

Sir i wanna ask i have 2 problem, so i use Nodemcu esp 8266 V3 different with you then on the Arduino when i run the code error i mean the problem is Nodemcu module what should i do ? Then for DHT 11 i use different to with you so the graphic can't working and LCD can't read that what should i do sir? Please answer sir

[@Freefire-h6v4t]

Bro It showing compilation error in SFE_BMP180

[@YUVARAJKR]

sir can we give the power supply to the nodemcu board

[@sritu_hobby]

Please use 9v battery

[@asggaming5390]

Sir code bhi upload ho ja raha h fir n led screen pe kuch dikh Raha n blynk server se ESP8266 connect ho raha h. Sare connection bhi miine 10-15 baar check Kiya please help sir

[@karthikgamers7069]

Thank you sir

[@sritu_hobby]

Welcome

[@diaryiklanlucudiarylancu8367]

Sir Add digital output relay for automatic and manual swicth?

[@RixtronixLAB]

//Creative video, thanks :)

[@sritu_hobby]

Thank you too!

[@aronnoarnab6438]

Thanks bro.Its working❤️

[@salehinahmmed9355]

Can plz give the I2c module library code which was used by you it will be helpful

[@aronnoarnab6438]

@@salehinahmmed9355 it was in my laptop bro..my laptop is not with me right now. I can provide it to you later.

[@YUVARAJKR]

Sir my lcd is not showing the measurments but i can read the measurments in blynk application what is the problem and lcd only show the green screen what can i do sir

[@YUVARAJKR]

Sir pls reply fast

[@19orkhan94]

Hi, The rain sensor shows 100% without water, but the percentage decreases when water falls on the sensor. How can I do it the other way around?

[@sritu_hobby]

You can change it using code

[@19orkhan94]

@@sritu_hobby Please can you change the code accordingly and give it back to me?

[@19orkhan94]

I did the code myself, but it doesn’t drop to 0. The minimum percentage shows 1 and when water hits it, the value rises to a maximum of 55.

[@pradeeptakar974]

LCD 12C is not displaying the output

[@DUYTHANHTV626]

sorry but i have a trouble, my ldr sensor dosent work, have something wrong in get value LDR sensor

[@sritu_hobby]

Check your sensor or jumper wires

[@ramyadhanala8279]

Can you provide list of components for this project and including cost

[@ketanpatil7146]

no

[@aprilladaru]

Hello sir, why not using bridge on breadboard? Can you explain please, thank you

[@sritu_hobby]

What's bridge?

[@aprilladaru]

@@sritu_hobby wire bridge to connect +- 2 side on middle of breadboard

[@aprilladaru]

@@sritu_hobby oh i see you using bridge on white cable, it's hard to see it

[@Ааааааа-т5й]

Hello? I can't find the port, will you tell me everything

[@sayax4464]

Hello I am in sti2d terminal and I have a project to present which is the smart cane for blind people and in this project I must use an accelerometer which plays the role of the motion detector and I must add the alarm clock/sleep function it that is to say when the cane moves towards an axis it lights up and when it does not move it is off. I need help because I'm really lost 🙏

[@sayax4464]

Can you help me ?

[@sritu_hobby]

What is your issue?

[@sayax4464]

@@sritu_hobby my teacher has already sent me a code I have to add a wake-up/sleep function of the cane for the blind, that is to say when the cane is at rest and it moves towards an axis (x,y,z) it lights up but when it does not move it is off.

[@engineeraatifmemon5872]

Plz help me I'm getting error in this project

[@HarbansSingh-ce2tm]

Good job bro...

[@sritu_hobby]

Thank you

[@sreyachakraborty186]

My ldr sensor only showing 1 light

[@amruthagrammu634]

Board name to install in arudion ide

[@YUVARAJKR]

sir how to install libraries

[@hanielfelix8501]

I can't connect my esp8266 card to wifi or blynk app, please help

[@sritu_hobby]

Please visit my blog srituhobby.com

[@AtharvRathod-e5s]

How much it cost to you , please tell me i have to make it in less time

[@sritu_hobby]

Description

[@anushay7726]

Hello sir port is not enable in arduino, what is the problem can you tell me sir

[@sritu_hobby]

Please include the COM port drivers

[@saqibhassan7552]

Hello brother im facing 'class LiquidCrystal_I2C' has no member named 'init' this error what should i do...

[@saqibhassan7552]

LCD displaying

[@saqibhassan7552]

plzz help bro

[@sritu_hobby]

Please include the I2C library

[@saqibhassan7552]

@@sritu_hobby i have included but its not working

[@saqibhassan7552]

@@sritu_hobby i have erase the int () command the project runs but lcd shows some ?.!.! theses signs

[@gurmansinghsidana1978]

Sir can we make this using raspberry pi 3 and without the use of breadboard as a pcb?

[@sritu_hobby]

Yes of course

[@gurmansinghsidana1978]

Can you tell how?

[@gurmansinghsidana1978]

I need to do it can you help me?

[@SubashSubash-h4k]

Bro I got error exit status 1 how to fix it

[@engineeraatifmemon5872]

Same problem

[@MdAzizulHaque-ht7yc]

Please provide source code. Your link isn't work.

[@sritu_hobby]

srituhobby.com

[@princechintu7960]

Coding is not working 💔💔💔💔💔

[@samarthsolanki2561]

Sir I can not find code link..... please can you help with it :)

[@sritu_hobby]

srituhobby.com

[@SaliyaEkanayaka-ul8np]

මෙක hoda ගැන තාම වැඩි 😢

[@aditprasetyo3651]

lolin or amica?

[@ketanpatil7146]

lcd,inti() pribllem in code cant solve

[@sritu_hobby]

Include the I2C library

[@vigneshp175]

Coding not working

[@yunusisrar4125]

Hi sir can i get you number regarding this project plzz help us our submission on monday