STALKER Kraken TAC-41 TDC Hopup Chamber Installation Video Short

[@ernstmeijer3067]

You will all love the Complete Stalker tac its top notch

[@stalkerairsoftdesigns5716]

thank u!

[@niksu1580]

I was probably the first one to order from Skirmshop! One minute after they came to stock. Super exited to get my Tac41 rocking!

[@stalkerairsoftdesigns5716]

Niksu, Good you are watching this video, next week we will make a in depth video about the installation and features. Many thanks for purchasing our product, it means you can expect more of these kind of upgrades on the market. Have a good day!

[@niksu1580]

@@stalkerairsoftdesigns5716 Cheers! Looking forward for the in dept video.

[@wizardthereaper]

Had you beat, skirmshop accidentally put it up 3 weeks ago and I bought it super excited then got an email that it wasn't available yet

[@elrulio9889]

i probably buy it before one minute sorry but nice try

[@Blinks_cb]

At 1:24 you seem to tighten a 3rd screw yet you only indicate the 2 flat headed screws are used? There is only 2 flat screws in the box. Can you please advise why you have a 3rd screw?

[@kerimercin6893]

Hi Chris, did you find the answer to this question?

[@stalkerairsoftdesigns5716]

hi thanks for asking. its not a 3rd screw. its the 1st and 2nd screw over and over again just a little bit until the set centers itself. it would be good to tighten one side completely and then the other set. so we advice to do it switched and devide the turns over the two screws until the inner barrel centeres and both screws get tightened at the same time.

[@WM84629]

Hi. I’ve got major issues with my tac 41 Stalker Kraken hop up. It hardly hops the bbs and if you put too much hop it just jams. It’s as if the Morpheus barrel sits too far in the chamber as if you pull it out slightly so the grub screws are off the cut outs the hop will work better. Can you advise what to do? The bucking is clean and air seal is perfect. This is using all your parts. If I put the stock parts back in the hop up works perfectly. I’ve tried multiple of your buckings and does the same with all of them.

[@stalkerairsoftdesigns5716]

@@WM84629 send to the shop back where you got it from, then i will receive it and show you how to install it. because all my parts are the same each batch and i install them weekly without any problems. if your hop doesnt hop its not installed correctly sorry to tell you. for any futher customer service please send an email to the shop you bought from with your order number in the topic. Thanks!

[@WM84629]

@@stalkerairsoftdesigns5716 Thanks for your response. I followed your install guide religiously. The kit is out of warranty so I can’t send it back. Do you have a number or email so we can speak directly

[@stalkerairsoftdesigns5716]

​@@WM84629they will still help you, can you send them the email for extra service?

[@WM84629]

@@stalkerairsoftdesigns5716 do you have any ideas to trouble shoot the issues?

[@stalkerairsoftdesigns5716]

@@WM84629 i don't know sorry i cant check it from here but it seems you are having an issue in other parts or with your order of how you setup the TAC-41 again. have u read our new product description carefull theres a build setup order in the description.

[@Yankee2-2Nomad]

Does the tool that you used to tighten down the cylinder head come with the Kraken? I havent seen it in any of the promotional material before.

[@stalkerairsoftdesigns5716]

It does not come with the kraken, we designed it to use in our tech department. If people like it we can release it maybe.

[@albro8853]

Especially that the cylinder head is a custom Stalker one, that tool should have been included in the hop up package, like silverback did for their cylinder head. 3d printing this would be a pretty low cost and would have been a nice touch considering the price of the hop up unjt

[@Yankee2-2Nomad]

@@stalkerairsoftdesigns5716 Please do! Its kinda nice to have a tool perfectly designed around the cylinder head and to also have an easier grasp on putting the cylinder head on.

[@stalkerairsoftdesigns5716]

I will do it, have to see what kind of material i can use to make it affordable for the airsoft. TBC 🤘🏻

[@longshotbutcher8003]

Is this a whole kit. Just looking at the barrel and I have the original one.

[@stalkerairsoftdesigns5716]

You can find complete upgrade kits with our inner barrel on www.skirmshop.nl Oir TDC unit works with GBB/VSR style barrel only

[@longshotbutcher8003]

@@stalkerairsoftdesigns5716 thank you

[@arkinator114]

I’m trying to install this on the 330mm twist barrel from silverback and it’s not goi g far enough to where I can put on the TDC wheel or the bottom screw, do you guys have a solution for this? I’ve put a shit ton of force into it and it’s just not going any further

[@black0960]

Hi, I've fitted mine today but have x1 oring and x2 tapered grub screws left over. Have I missed a step?

[@stalkerairsoftdesigns5716]

No, its totaly fine! You need to check which O-ring fits the best on your cylinder because we think not all cylinders have the same diameter so we included two different O-rings for the cylinder head. 1 small, 1 bigger. For the screws, the pointy grub screws are for inner barrels with a small side cut, the flat grub screws are for stalker morpheus inner barrels and align the inner barrel a little better with big flat grub screws. Game on!

[@Diggilicious]

Do I have to have morpheus barrel for this? Or will the stock barrel work?

[@stalkerairsoftdesigns5716]

advice to use the stalker barrel cause all parts we make are made for eachother but, you can use our hopup with other GBB open cut barrels sometimes but the best performance you get out of our complete set because its made for eachother.

[@Racenietzohardjo]

Whats that tool you use for the cilinderhead at 2:55?

[@stalkerairsoftdesigns5716]

We made some for our tech department and using it for over a half year now. Its nice and strong! Maybe we should release it for the public..

[@IsteMortuum]

@@stalkerairsoftdesigns5716 pls i need this

[@benchapman2703]

Is it just the outer edge of the screw on the bolt you need to sand down?

[@stalkerairsoftdesigns5716]

IF your bolt does not go down like normal but stif, then sand this bolt nut a bit down. This is the reason why your TAC41 is so silent after this installation, you make a FIXED setup so your bolt set does not wobble or moves when you are shooting. this means your setup is fixed and steady between receiver and front of hopup. all the shocks go trough the rubbers and there you go ;) good luck!

[@benchapman2703]

@@stalkerairsoftdesigns5716 thanks for the info, I have sanded it down but now after a few shots the spring guide stopper starts to pop out and I am unable to pull back on the bolt. Any advice?

[@stalkerairsoftdesigns5716]

@@benchapman2703 Hello, then you are probably use a short spring for the TAC41, maybe you can use rapax lightpull, silverback spring length or similar length spring, then your problem is solved. You can use short springs like rapax RMS but then you need a thicker bumper pad in the cylinderhead, we sell them in 3mm, 5mm or 7mm and right now you have 3mm. 5mm will eat a bite more volume but its a thicker rubber so it will absorb the impact of a piston slightly more than a 3mm rubber. The spring guide stopper of the TAC-41 needs the tension of the spring to be able to kept in place, if u use a shorter spring then you change the tension and then the guide stopper can wobble or in worst case, can fall out. You can choose one of the methods we wrote above and the spring guide stopper will be kept in place.👍🏻

[@benchapman2703]

@@stalkerairsoftdesigns5716 So I am using a Silverback m150 spring, do you think I need to switch it to a Rapax 2.2 spring?

[@stalkerairsoftdesigns5716]

@@benchapman2703 i use it myself as well works like a charm

[@enonock]

i follow the video on YT a and upgrade stalker GBB hop chamber step by step. other upgrade part are 420mm morpheus inner barrel+ rapax 2.8J spring. when I tighten the hop ,fps go up. (max:168m/s) loose the hop ,fps go down. (min: 155m/s) whats the problem? air seal issue?

[@stalkerairsoftdesigns5716]

hi there thanks for upgrading with our parts. the thing you notice is normal, its called joule creep :) you can read a lot about it on internet.

[@a__rbd]

hello , quel est épaisseur du joint vert ?

[@stalkerairsoftdesigns5716]

www.skirmshop.nl/en/anti-shock-rubber-pad-set-3mm-111915562.html

[@elrulio9889]

Ce petit joint beaucoup de gens vont le négliger pourtant ca va faire toute la différence niveau son

[@stalkerairsoftdesigns5716]

vous pouvez simplement utiliser l'épaisseur que vous voulez, il existe différentes épaisseurs disponibles. l'épaisseur que vous obtenez est de 3 mm