Good information and straight to the point. In most other videos I have checked out, the person doing the video seems to enjoy hearing themselves talk. This guy gets to the point without all the b.s. Thank you Mr. Fortin for taking the time out to do this video, it helped me solve the problem on my 79 El Camino.
@josephpuchel64974 жыл бұрын
Hey nice tutorial video but I think you should have used a light to brighten up the area in question. The engine was on a stand.
@a1goines15 жыл бұрын
Man thank you so for showing me where the shims go. Thanks SOOO much!
@trickydick43117 жыл бұрын
This guy actually shows you how to shim it
@notoriouselwood92534 жыл бұрын
This is a well thought out explanatory video. The masses need accurate and concise direction. More!
@mexicanfrenchman69844 жыл бұрын
nice job no wonder i have went through so many starters i never shim i will now thankx
@elimonjal5 жыл бұрын
Great video, learned alot. solves my problem.
@ganjagod42066 жыл бұрын
Thanks alot this video was the best one I've seen
@olenairsoftguy883 жыл бұрын
great vid
@tj11477 жыл бұрын
this only works to keep it in good mechanical condition. As far as starter not working, you might want to check the starter control circuit. You can also have a few teeth broken off of the flywheel/flexplate, this will sound like a starter with a stripped pinion gear.
@johnniesmith7214 жыл бұрын
I put a starter in my car with no shims...it doesn't grind but it makes a knocking sound and wont start but after a few ignition turns it will start...will shimming eliminate this?
@kevinwright5973 жыл бұрын
Damn good information !!!
@gilbertdavis5064 Жыл бұрын
It was really great help my name is Gil I'm from Oakland
@rx7cl6 жыл бұрын
good job.....
@user-fh6ft4bp2i Жыл бұрын
Г- ключ сколько мм? 5, 6?
@kanz28444 жыл бұрын
hello I need your urgent help ... send this message using the google translator because I do not speak English so I don't know if it is understood ... My problem is this, I have a Chevrolet v6 229 that suddenly began to break the cover of the starts . Have the engine flywheel or "flexplate" repaired and when you turn it on, the starter locks and generates force ... what can it be (the boot has its respective shims) what is the distance in "centimeters" that should be the start? , will it be necessary to use 3 shims or more? ??
@tj11474 жыл бұрын
It is a SAE measurement between the pinion shaft of the starter and the ring gear teeth. 1/8 of an inch. In metric it is 3.175 millimeters. This is assuming the ring gear teeth are in good conditions. If they are worn, they will need replacements. I hope this helps you.
@notoriouselwood92534 жыл бұрын
Exactly
@linz57827 жыл бұрын
Hi ..so I put starter on. worked fine came home started it on to check if it turned on. but know it sounds like what your saying, so did it do that . sorry this was my first time putting a starter. I didn't know nothing about the shim thing. so the Other question is could know the starter or flywheel brake? or do I have a chance to put the shim. I really don't know .thanks
@tj11475 жыл бұрын
If your flywheel is broken, you need to remove your transmission and torque converter, there are six bolts that hold the flywheel in place fastening the back of the crankshaft. Also, is it possible that you didn't have the bolts tight enough? Check your torque specs for the application you are working on. This is a Chevy, 350 cid engine. I'm sure that it is the same for most small block engines, and a few small block based v6 applications like 4.3 vortec. But mostly the same for rear wheel drive GM models.
@tj11475 жыл бұрын
Also, if the flywheel broke, damage has already been done. But after replacing the damaged flywheel, it is very important to properly shem the starter during the final installment.
@studeystudebaker3 жыл бұрын
my problem is my replacement starter is to far from the teeth your allen is probably 1/8th inch so i din;t need shim how would i get it closer,do i just need to go get a different starter thanks
@tj11473 жыл бұрын
You might want to check the condition of the ring gear on the flex plate or flywheel.
@jonhsmith2706 Жыл бұрын
Mines gap is too far nothing was wrong before after 2 months started grinding I replace starter twice I have the right bolts no cracks in block I'm really just tired of car
@jbandshahayeah18627 жыл бұрын
How on earth can I even do this test, when the starter is installed, there's no where for me to insert the Allen key
@lucasrasmussen52986 жыл бұрын
Paint the pinion gear to see where the flywheel hits it, install the starter, start it a few times and pull the starter out to check placement
@tj11475 жыл бұрын
Usually, this only works on some older GM vehicles, you can take the flywheel cover, yes it's hard to do unless you have the engine on a stand. It can be checked installed, just really hard to reach.
@andremoncree40282 жыл бұрын
A flashlight would have been great!!! I have no idea and can’t see where your sticking the key at😩. I have no mechanical skills and need help. Still stuck a square one.
@ezwa99792 жыл бұрын
I still don’t see how to shim, EvN on Ur viDO was recognizes that no one shows how to shim, I watched it & I STILL don’t know where to put these shim gizmoz👋