Steel Design L5G| LSM| Compression Member | Analysis of Single Angle Strut| Numerical Problem| Hindi

This video lecture is suitable for Civil Engineering students and aspirants who wish to brush up on their basics.
References:
• Limit State Design of Steel Structures by S.K. Duggal (Mc Graw Hill Publication)
• NPTEL Lectures on Steel Structure Design by Prof. Damodar Maity.

[@maheshkumar559]

Please also provide the lecture of RCC and structure analysis

[@40rajanandce82]

Love the way of teaching. Please complete whole DSS syllabus

[@civilengg.withakriti2556]

Stay tuned 😊

[@samarjeet5578]

I don't know why... But every mam teaches far better than sir... Thanks a lot mam ❤

[@civilengg.withakriti2556]

You’re welcome 😊

[@gk7800]

Mam plzz start competitive exam series Also which book is better for the preparation of PWD JE.?

[@civilengg.withakriti2556]

Books by authors "Gupta and Gupta" and "Agor" are good for competitive exams with multiple choice questions.

[@gk7800]

@@civilengg.withakriti2556 thanks mam😇...

[@Pitapuramthaluka]

Mam i love you ❣️🎉

[@civilengg.withakriti2556]

Thank you ☺️

[@undrothukarthik7891]

Mam please do videos on slab base concrete pedestal

[@civilengg.withakriti2556]

I’ll try to cover it

[@undrothukarthik7891]

@@civilengg.withakriti2556 mam please do video on concrete pedestal

[@kks9502]

How to calculate using the same procedure if one end fixed and the other end hinged? What extra we have to do other than what you explained for each end fixed? In such case we will have two values of both "equivalent slenderness ratio" as well as "Fcd values" ; then what we will have to do next? PLZ REPLY

[@ShambhuKumar-zb1kf]

Thanks mam Very useful 👍

[@civilengg.withakriti2556]

Welcome 😊

[@amritpainuali2589]

Thankyou.

[@civilengg.withakriti2556]

You're welcome

[@SaarthRaisagar]

Mam, the first condition was one bolt at each end. What does this mean? Is it not one bolt at each legs are connected? If it is so then it should be eccentric connection not concentric. Pls explain

[@Civilocity.]

Thank u so much mam

[@civilengg.withakriti2556]

welcome 😊

[@vatsalyanetam7945]

mere steel table meh yeh value nhi hai mam

[@priyankapriyadarshinisahoo7582]

Maam, can we use tables for values of FC’s instead of formula?????😅😅

[@civilengg.withakriti2556]

Yes that can be used But in subjective exams you might not be given marks for steps if the answer is incorrect

[@sanketkadwade4263]

Mam from where the k1 k2 and k3 values are taken ?????

[@civilengg.withakriti2556]

Table 12 of IS 800 : 2007 Depending on the end conditions given in the question

[@Civilocity.]

Mam angle section steel me kha h

[@civilengg.withakriti2556]

Please go through all the videos… numerically on angle section have been discussed

[@samhithbeeravelli9412]

gross area wont be decreased with the bolts?? nat sure.....

[@civilengg.withakriti2556]

No gross area will remain same… Effective area decreases

[@MukeshKumar-xy2tz]

Mam, ye qus. LSM ke according hain ya WSM ke according ??????....

[@civilengg.withakriti2556]

LSM. It is mentioned on the first slide.

[@MukeshKumar-xy2tz]

@@civilengg.withakriti2556 first slide??????

[@civilengg.withakriti2556]

The questions have been solved using LSM

[@MukeshKumar-xy2tz]

@@civilengg.withakriti2556 ok Thank you mam

[@shwetakashyap7503]

How to contact u mam,, Plz reply mam I have doubt in steel

[@civilengg.withakriti2556]

Post your query in the comment section

[@hsbtestudyzone]

Mam fixed ya kuch bi nhi diya gya ho to

[@civilengg.withakriti2556]

Take k=1