STEMCO® offers installation training for the King Pin with the Qwik Kit®
Пікірлер: 43
@spewgilist4 жыл бұрын
I wish all repair demos on KZbin were this succinct
@dannyyo79487 жыл бұрын
actual is to torch to slight or bright cherry red then use largest special tool sledge hammer, and to finish with rattle can paint.
@c50ge3 жыл бұрын
At 0:57 notice the old king pin lands standing on concrete, let’s see you do that again!
@CTSCAPER5 жыл бұрын
That was a very thorough video.
@johnhutsenpillerjr17854 жыл бұрын
Very professional video Sir.
@DR-um2bvАй бұрын
Are these better or worse than than the 1's with yellow plastic on inside of bushing . How often should kingpins be greased?
@SYLVESTERHOPEevenstephen3 жыл бұрын
Where Can I purchase the King Pin Bushing and Seal Tool
@Chibchombia1003 жыл бұрын
You're just professional... thanks a lot
@lukachilufya-mw1ps Жыл бұрын
For how long does it take to remove and fit a kingpin
@7thfloorisnomoreq7906 жыл бұрын
That wasn’t a brass or dead blow hammer
@zainengalerion68324 жыл бұрын
What kind of sorcery did you use to get that damn bushing in? I've been at it for hours for just one... still can't get it started...
@makeitpay82413 жыл бұрын
there is a special stepped driver
@cbmech2563 Жыл бұрын
I love the kaiser kits and I've never had a problem getting the spiral bushing started
@thomaswhetstone2870 Жыл бұрын
Just turn and press at a angle honestly just like he said it'll shrink together so it'll roll right in
@cbcarper9681 Жыл бұрын
Excellent excellent excellent
@ابوجاسر-ف3ح2 жыл бұрын
Thank you
@Muddinguy7 жыл бұрын
Yeah I think ive had them come apart that easy.. umm never..
@ConTheDon1874 жыл бұрын
haha same. I'm gonna need a tiger king pin removal tool pretty soon here.
@bmdbigfeet10314 жыл бұрын
@@ConTheDon187 No shit. Why don't they show a video where the pin is just alot more than stubborn. And I haven't seen a tiger tool for these yet. Could sure one.
@ConTheDon1874 жыл бұрын
@@bmdbigfeet1031 I can tell you my boss destroyed one of these on a kingpin that was seized to the bushings in the knuckle, it's why I'm hesitant on buying one right now, if it fails in the middle of a job its gonna be very problematic.
@bmdbigfeet10314 жыл бұрын
@@ConTheDon187 I looked up the tiger tool and it exists. I ended up making my own pin press and it worked but not without any help from a torch. I made the bottom narrow but wide enough for the pin to push through while I had a 10 ton porta power on top. Found a piece of grader cutting edge for the top plate clamp, used 1in ready rod through the top clamp to the bottom and proceeded to pour the juice to it. The portapower was maxed out then I went for the good ole gas axe. Had to climb back into my skin when it finally popped. Was all down hill from there.
@ConTheDon1874 жыл бұрын
@@bmdbigfeet1031 yeah for the cost of this tool I think I'm just gonna make a jig for my 20ton pneumatic jack and give it a go
@CosgroveNotts7 жыл бұрын
Never fanny about like this lol ever!
@maxpuppy963 жыл бұрын
Ten thousandth's? This guy wants to sell king pins.
@10YearOldTom3 жыл бұрын
Don't heat axle. This tool never touched a bus.
@MarcoHernandez-du6im2 жыл бұрын
That’s what I was thinking, I’ve done kingpins on MCI buses and dang those Lock pins are a pain in the butt I basically have to melt them with a torch.
@heribertomejia91365 жыл бұрын
Good
@discoveryman594 жыл бұрын
Is this the training video you use when you try to recruit women into the field?? No need to use any force on a king pin they just FALL out ladies.
@Mazda_Geek3 жыл бұрын
Yeah bullshit 😂
@Chris-zm7wh2 жыл бұрын
It’s says use brass or dead blow proceeds to show the guy using a normal hammer lol
@kc8tyk86 Жыл бұрын
You must need a eye exam its clearly brass.
@solidgoldeazyaction8 жыл бұрын
He got hurt what a noob
@chukoyo49035 жыл бұрын
Español
@shatteredsquare3 жыл бұрын
ok then!
@slimjohn20902 жыл бұрын
This ain't real life 🤣
@bobocaterpillar36974 жыл бұрын
looks like a REALLY TEMPORARY cheap fix! all that labor... just buy new knuckles ....
@lynxstarautomotive2084 жыл бұрын
I agree.
@davidortega79574 жыл бұрын
bobo caterpillar- YOU GOT NO IDEA WHAT YOU ARE TALKING ABOUT DUDE!!!
@bobocaterpillar36974 жыл бұрын
@@davidortega7957 oh, ive done these CORRECTLY, HUNDREDS of times before... the RIGHT way to do it is to press in new bushings with tooling and HONE them to fit ( also with special king pin tooling ) .... NOT screw in a cheap ass looking piece of SOFT metal! this looks like stuff you do to a truck going to *auction* !! i bet it doesn't get HALF of the life of the original! oh yeah ... and NEVER seen kingpins come out this easy before! 0:50 🙄 yet again ...their is a pin pressing tool to remove stubborn pins for that $$$$ big trucks = big money
@walterbrown42783 жыл бұрын
Hundreds of times. You sure you are doing it right. I have used these and never had no problem with them. If you done it hundreds of time then you must work in a alignment shop and don’t own a truck
@j06c3 ай бұрын
You got a part number for the driver you use to take them out