I built my 4.0 for fuel mileage. It has a tune, upgraded pistons, and rings,balanced rods, new cylinder head with LS valves, and mopar performance spings, Harland sharp roller rockers, re-sized ford 300 injectors new fuel pump, aluminum fuel rail, bbk throttle body, mishimoto radiator, with an upgraded fan, Afe power header with magnaflow cats. I get about 19mpg highway on 31 inch tires and a 6 inch lift.
@mercedescherokee68534 ай бұрын
Same, I built a 4.2l mini-stroker, factory head, factory cam, and electric fan conversion, I can get about 20 highway if I drive slow
@TheGrimFoot4 ай бұрын
@mercedescherokee6853 that's pretty schweet. I'm guessing 55-60 mph Is the sweet spot.
@mercedescherokee68534 ай бұрын
@@TheGrimFootyea about 65, my tires are a little bigger than factory so a little more speed puts it in a good rev range
@BrettMods2.04 ай бұрын
@mercedescherokee6853 what's the mileage like?
@TheGrimFoot4 ай бұрын
@@BrettMods2.0 he done guarandamn told you 20 highway
@andrewstowe574 Жыл бұрын
Those leafs being broken would definitely affect your ride! With that much rust, replacing those with the lift is highly recommended. I get 15mpg highway in my '98 on 35s. Just gotta keep the throttle bottle clean, air filter clean, and plugs/wires good. That 4.0 will run forever!
@aidanmakinster922 Жыл бұрын
What tires are you running?
@elijahk5398 ай бұрын
I have a collapsed lifter in 2 of my cylinders on my xj 4.0 and I get barely 10 mpg on 31’s with a 3inch lift. I’m just gonna run it till it blows cuz I got my dad’s 4.0 with 70,000 on it for my Jeep with gears and custom lift waiting for all the pieces for 35’s. hopefully when I get the other motor in there is gets better mpg
@austinc817611 ай бұрын
*This is why your jeep gets BAD gas mileage* “I have no idea if that even did anything”
@Enigma-Sapiens Жыл бұрын
When you start losing oil pressure it could be worn out rod, main, and cam bearings. As a temporary patch, you can run a thicker oil.
@christopherpilcher63472 ай бұрын
Just a tip. If you put the jeep in 4wd with the tires on the ground you wont have to use a pry bar to hold the front drive shaft from spinning.
@tomandhistruck10 ай бұрын
Those shims should go in the rear. If you are vibrating in the rear, pinion angle is usually the culprit. Those shims will alter your pinion angle.
@officialWWM Жыл бұрын
Have another look at that rear spring. It’s not just the shim that’s broken, 2 of the springs are broken too!
@stevennewellproductions Жыл бұрын
Good call! I totally didn’t see that
@officialWWM Жыл бұрын
@@stevennewellproductions that could be a dangerous situation!
@nadrojfan Жыл бұрын
Yep! I saw that, too. Time for new springs.
@mikewilson7132 Жыл бұрын
1 it is a brick 2 its lifted 3 heavy large tires that is why they will get between 12 and 14 in town maybe 18 to 20 on hwy you dont buy these for gas milage
@Neilman10007 ай бұрын
Steven, I believe that "Just Dex It" was able to prove that the low oil pressure at idle is primarily caused by worn camshaft bearings. Check out his resent KZbin videos. Be safe.
@gregj.gotham4402 Жыл бұрын
Shaking up front called death wobble need new bushings or replace the whole control arm lower and upper, do alinement. Those angel pcs under the rear springs you need them, you must point rear drive shaft to the pinion of the SYE minus 3-4 degrees less in angle as you hit the gas the entire differential rotates up wards so -3 -4 is perfect. Chech on line at Woods drive shafts will have videos as to the angle of drive shaft explained very well.
@tonyking3138 ай бұрын
Use "mass airflow sensor cleaner" to clean the IAC. It's designed for non metallic parts. Carb cleaner is designed for metals.
@Deadbuck73 Жыл бұрын
0-60 in my XJ? It’s been 17k since I started daily driving my Jeep jeep. Not once has it occurred to me to do such a thing! 🤣
@wtforce5512 Жыл бұрын
yes cleaning MAP IAC and throttle body does in fact improve air flow thus improving gas mileage/engine performance. Getting it over 3k RPM is not lol. I feel like I get 3+ mpg better when I’m not heavy on the skinny pedal. I can get anywhere between 15 and 17 mpg in my 99 on 32s with 4.10 gears and 302k on the dial.
@Deadbuck73 Жыл бұрын
Absolutely. Going easy on it is key. I have a 99 stock height. I find just about 40mph and a lil above gives me the best mileage. Seems to be the sweet spot.
@mercedescherokee68534 ай бұрын
Ive replaced multiple oil pressure sensors with oem 2 wire sensors, they dont read accurately at all, you need to run an aftermarket gauge to know what it reads, with hot oil on a new build it will drop down to 13psi coming off the highway to idle fyi
@smiles_per_gallon11 ай бұрын
Just to make sure, did you disconnect the negative battery terminal before performing work on the sensors? And then once you complete any work involving sensors, you disconnect both positive & negative, then make contact with both terminals for a minute to have the computer relearn the sensors? I just want to make sure I’ve got those steps down. I’ve also got an O2 sensor I need to replace.
@averagejoe82135 ай бұрын
You've REALLY got 350,000 miles on that thing!? That's awesome! Mine's (same color) a 2000 with 147k and I'm hoping to get it past 300k! Great video!
@NomadMonster5 ай бұрын
Your comment about your bolt heads 'rounding'... I see a lot of Jeep KZbin videos where the person is not using metric tools. For many decades, all the bolts on Jeeps are METRIC, so if you are using Imperial sockets, you may be close, but they will not fit correctly and rounded bolt heads is the result.
@Brian_C_Ай бұрын
Late to the game. The claim of "I'm not a mechanic" is kinda weak. If you're going to own older vehicles, like an XJ, and experiment on it, you need to swim on your own or be ok with paying money that could be invested elsewhere. There are very few regular shops you can take these to who will have any idea of what to do with some of that stuff (Look at Rainman Ray's Repair where he had an XJ come to his shop - good dude, but obviously not a Jeep guy). Also, if you don't know what your driveline angle should be with a stock vs. SYE/driveshaft combo, there are oodles of resources out there. In a nutshell: parallel angles for transfer case/Diff output/input (same angles at both u-joints) vs. point the pinion at the T-case for an SYE (minimal rear u-joint deflection). JFC, bust some rust on that thing before there's nothing left...
@elev8j10 Жыл бұрын
You brought this to a shop and they didnt let you know your missing leafs and a shim on one side? How thats broken off will definitely cause issues possibly dangerous ones. Those shims are there for pinion angle and you do need those depending on what your drivetrain angle looks like.
@Cowboy66SEVEN Жыл бұрын
Timed the 0-60 for you. About 16 seconds.💨💨💨💨💨💨
@stevennewellproductions Жыл бұрын
😂
@biglion750311 ай бұрын
btw you can just easy swap a set of 01-04 wj front brakes and knuckle setup with the tie rod and drag link setup for stronger front brakes, and steering, but also the lower control arms from the wj also were beefier and gave some room for bigger tires. its a somewhat simple swap that 'D&E in the garage' did a video about here. -> kzbin.info/www/bejne/baWnnZh-d7CNZtUsi=OQSn6IyZ0kk6snwF
@carldietz9767Ай бұрын
You also have 2 broken bottom spring leaves on the driver's side!!!
@Alx26727 ай бұрын
I cringed hard when you cranked down those throttle body bolts into the aluminum manifold
@TRUMP20Z427 күн бұрын
Green on red looks awesome actually.
@jeeper4269 ай бұрын
Chrysler service manual for resetting ECM Disconnect Neg Battery Terminal, isolate from battery turn ignition switch to ON position, wait for 3 seconds turn headlights to ON position, wait 3 seconds Turn headlights to OFF position and return ignition key to OFF/Lock position touch neg battery terminal to pos terminal for 3-10 seconds turn headlights to ON position turn headlights to OFF position re-attach Neg battery terminal to battery neg post turn key to ON position, but do not start turn key to OFF position cycle key back to ON position cycle key back to OFF position Cycle Key back to ON position for 3rd iteration, watch CEL for any error codes, if no codes present check manual for flash sequence for end of code list cycle key off and back on start engine not sure why they make it such a dance to do this and this is from the Chrysler/Jeep Factory Service Manual for Daimler Chrysler vehicles 1990-2001 Jeep Cherokee XJ also I've seen dirtier throttle bodies, but that one certainly needed cleaned, cool project rig, a 2JZ in an XJ seems like a wild swap but i'll bet she runs good
@elijahk5398 ай бұрын
I have a collapsed lifter in 2 of my cylinders on my xj 4.0 and I get barely 10 mpg on 31’s with a 3inch lift. I’m just gonna run it till it blows cuz I got my dad’s 4.0 with 70,000 on it for my Jeep with gears and custom lift waiting for all the pieces for 35’s. hopefully when I get the other motor in there is gets better mpg
@getbusylivenordien5394 Жыл бұрын
Lol typical internet and jeep forums Those bolts are not sae they are metric So why not buy if you don’t have a good set of metric tools and stop stripping your bolt heads with the wrong size tools when using sae Oh and stop using jeep sites that give bullshit information Oh wait you would have to not use any of them Lol
@j.finesseflights14035 ай бұрын
That red jeep must be the older version, Renix? My 95 didn't come with a green valve cover and the newer jeeps have the exhaust on the Dr side! 😂
@pekwalker Жыл бұрын
I am in the process of buying one of these vehicles and you mentioned a forum for them. Could you please share the link to the related forum? Thanks.
@stevennewellproductions Жыл бұрын
Xj Jeeps on Facebook
@kaseykrippner31935 ай бұрын
You sure the oil pressure is not just a poor connection. Mine reads 0 to 10 at idle, if I go flick the sending unit with my finger it will start reading around 38-40 and then fail after a few seconds dropping down to very low reading
@2tranceform Жыл бұрын
o2 sensor? Definitely affects mpg's.
@equals-kl9hm9 ай бұрын
Green/ red are contrasting colors . . . sort of. The reason you don't care for the colors is you have the wrong shade of green. Try a cheap color wheel and dial in that color.
@wesg3084 Жыл бұрын
A fellow Masshole and fellow XJ owner. 🙂
@stevennewellproductions Жыл бұрын
🤝
@irish12095 ай бұрын
Same 💪. South Coast. And my XJ also gets dismal mpg. 💀☘️🍻
@deathbeforedishonorflossdo65013 ай бұрын
You have to jeeps in you video I also own two one white on 94 grand Cherokee and a black sport I love both trucks hey let's bring back the jeeps
@jesseguagliardo8644 Жыл бұрын
What’s the whole wheel size set up? Rim size, tire etc
@stevennewellproductions Жыл бұрын
15x-10 Mickey Thompson wheels. 33x12.50 iron man all country
@mr.2cents.8465 ай бұрын
Actually looks hot with those tires. 😎
@texture6 Жыл бұрын
I’ve been looking at UltraGauge OBD2/OBDII. What do you think?
@benitotollett92884 ай бұрын
Where can I find parts for a 1995 jeep cherokee
@theangrycamper2 ай бұрын
lol, no, its because I have Dana 44s, 37s an RTT and a shit ton of armor ha ha ha ha ha
@cratz519 Жыл бұрын
hey! where did you get those jeep cheorkee sport seat covers? those are sweet!
@stevennewellproductions Жыл бұрын
They came with the 2JZ XJ when I bought it
@squelchtone2 ай бұрын
413 XJ's unite!
@firesorcererfs6029 Жыл бұрын
What can I do my cherokee xj is 2wd but I added 4.5 inch lift and 33’s what could I do
@StayAtHomeMomOf3 Жыл бұрын
Thank you for teaching me. I had no clue definitely learned a lot in just watching this video. You do incredible Job keep it up
@Nigriff8 ай бұрын
Thanks mom. What did you learn???
@mr.russerzplace...144822 күн бұрын
My zj has 300239 miles and it gets piss poor mileage. It's got a v8 ..eerrr
@officialWWM Жыл бұрын
Those bolts are 10mm!
@stevennewellproductions Жыл бұрын
5/16 six point worked better
@NTfoolhardy Жыл бұрын
Don't look up what tool you need. Look up how to use the tools you have.
@derekcrooks76698 ай бұрын
Because 11/16 is wrong… they are 5/16s
@Nigriff8 ай бұрын
Clickbait. All I learned is you wasted my time.
@michaelangelos511710 ай бұрын
It's metric
@davidlittlefield2483 Жыл бұрын
Unnecessary click bait title.
@stevennewellproductions Жыл бұрын
Not clickbait at all…. 😂🤷♂️
@stevennewellproductions Жыл бұрын
A dirty throttle body would be the reason you get poor gas milage…
@davidlittlefield2483 Жыл бұрын
@@stevennewellproductions You made an unproven assumption without before and after measurements of gas mileage.
@johannjohann65232 ай бұрын
Jeep is crap. As a professional mechanic I refuse to even work on them./ Poor design. Poor handling. Poor 4 wheel drive capapbility but they are supposed to be known for their 4 wheel drive capability . Ha! Chrysler/Jeep sucks.