STIHL CHAINSAW NOT OILING? THEN YOU NEED TO GO CHECK THIS RIGHT NOW!

  Рет қаралды 12,054

THEMOWERMEDIC1

THEMOWERMEDIC1

Күн бұрын

Пікірлер: 43
@helicopterjohns
@helicopterjohns 3 жыл бұрын
Thanks for sharing. Liked your oil pump puller!!!!!!!
@adnacraigo6590
@adnacraigo6590 3 жыл бұрын
Oh, l like your haircut. I like to keep mine on the short side too.
@cclow9494
@cclow9494 Жыл бұрын
A thoroughly enjoyable watch. The best of attention and care from the medic and no health insurance required!
@braddempsey6930
@braddempsey6930 3 жыл бұрын
Great video mate, the guy I work for has that same issue with his pole pruner, I'm sending him a like to your video immediately 👍
@joeortiz3455
@joeortiz3455 3 жыл бұрын
Awesome lesson teach! Very well explained
@RafaelHernandez-ks2bs
@RafaelHernandez-ks2bs 6 ай бұрын
Nice jobe buddy you are a good mechanic
@cliffcowdell9760
@cliffcowdell9760 Жыл бұрын
Going to attempt this. Thanks for the part about spinning the cutter head with the tool. That will help. You are the man.
@moorflash200
@moorflash200 11 ай бұрын
Great video. That's helped me out and saved me £210!
@adnacraigo6590
@adnacraigo6590 3 жыл бұрын
Very informative. Thanks.
@jimmydickson8854
@jimmydickson8854 2 жыл бұрын
Thanks for the practical tutorial very help full ,point taken clean your gear first ,thank you ,jimmy Australia
@MikeJones-jr5hb
@MikeJones-jr5hb 3 жыл бұрын
That’s good to know! Thanks!
@Terry_Baker
@Terry_Baker 3 жыл бұрын
Great video as usual Jeremy. Got a similar little puller set up for pulling those pumps. I usually find they’re clogged with saw dust.
@mferrarorace
@mferrarorace 3 жыл бұрын
Great video Thank you!
@motoman5023
@motoman5023 3 жыл бұрын
Great video!!
@SERGUMUM
@SERGUMUM 10 ай бұрын
Great video!.
@johnsomerset1510
@johnsomerset1510 2 жыл бұрын
Great video and you are spot on with everything except (everything is filthy) you don't say how to check the action of the pump itself! As the gear (and plunger) is rotated on the end of the pump unit, it must go in and out slightly at the same time (8:36). This is what makes it pump the oil (sucks on one side, rotates 180 degrees and squirts out on opposite side orifice). I took my Stihl chainsaw apart today because it won't pump oil and found the plunger just spins, instead of oscillate in and out as well. This indicates the side pin that engages the cam groove on the plunger, has sheered off. So, I'll be ordering another on ebay in a minute. The part is too cheap to bother repairing.
@rogermcdonald1607
@rogermcdonald1607 3 жыл бұрын
Nice video Jeremy! Ive never seen one of them apart! I have now.🎬🇺🇸Roger
@heavysnow8616
@heavysnow8616 3 жыл бұрын
I have found a few, all on Stihl saws, exact issue as posted. Check em or get em checked!
@garyhockensmith2471
@garyhockensmith2471 Жыл бұрын
I use simple green at a 1-1 ratio and spray the head and redivide with it and rinse it off, takes less then a minute and won’t damage the rubber gasket and will clean it right up! I was surprised when someone told me about it! Better then brake clean and cleaner
@nashguy207
@nashguy207 3 жыл бұрын
Good Job Doesn't look to difficult to do. Is the pole saw attachment in the kombi the same?
@markhoward142
@markhoward142 Жыл бұрын
What size screw?
@shannonwhitaker9630
@shannonwhitaker9630 Жыл бұрын
Use an old small paint brush to clean around your caps (pole saw, chainsaw, ect) before you take them off. If you want to do this job more comprehensively remove the top half of the gear case with gearhead chucked in vice by the limb hook. Tap the pump out the housing with a small flat punch. Install cleaned pump from the bottom and watch alignment of pump discharge port side. Clean, re-grease and re-seal gear box housing. Pretty easy job.
@trevorhunter374
@trevorhunter374 3 жыл бұрын
The STIHL pump gear goes in and out as it spins. Maybe that’s how it pumps. Very clever. Good video
@philliphall5198
@philliphall5198 8 ай бұрын
Guess I missed what size bolt was used to pull pump ???
@jerrysoutherland662
@jerrysoutherland662 3 жыл бұрын
Jeremy another great video.I am working on a HT 101 polesaw at this time,rebuilt the carb. Pressure tested and vacuum tested it no leaks,will throttle up won't idle change the fuel lines and filter,spark plug.Can you pressure and vacuum test a 4 mix for a air leak, Thank you.
@luisramirez4905
@luisramirez4905 5 ай бұрын
Muy buen video amigo lo felizito grasias
@44place85
@44place85 6 ай бұрын
Just wondering, how do you change the spur gear?
@chet3louisiana558
@chet3louisiana558 Жыл бұрын
Great video. My oil valve/breather is leaking. Any advice on getting it out or cleaning it out? I'd rather replace it. Thanks.
@majstealth
@majstealth 11 ай бұрын
clean it from the ourside, push a small opject in it, to move the ball and hopefully reseat without debris between the ball and the funel
@chet3louisiana558
@chet3louisiana558 11 ай бұрын
thank you@@majstealth
@johnkosheluk1041
@johnkosheluk1041 3 жыл бұрын
All.you have to do is clean the dirt in the oil pump and put it back on
@THEMOWERMEDIC1
@THEMOWERMEDIC1 3 жыл бұрын
That’s correct
@johndemus
@johndemus 3 жыл бұрын
Thank you mowermedic1
@mikemccabe1324
@mikemccabe1324 3 жыл бұрын
If they made the oilers do what they’re supposed to do...they wouldn’t sell as many chains. Why would they want to possibly supply the best designed fully adjustable oiling system with sufficient flow in any condition? Husqvarna Rancher is notorious for oiling system issues.
@johnkosheluk1041
@johnkosheluk1041 3 жыл бұрын
No if you look on the inside of the case there is a diagram
@majstealth
@majstealth 11 ай бұрын
you dont have compressed air in your shop, do you?
@johnkosheluk1041
@johnkosheluk1041 3 жыл бұрын
You pull the pump out and clean the dirt out and put it back on it will oil trust me I do a lot of them
@stvpls
@stvpls 3 жыл бұрын
a guy i know has got a barely used hvsquarna chainsaw thats not pumping oil could it be the same issue?
@johnclarke6647
@johnclarke6647 3 жыл бұрын
How about 5 mm x 1.25. A regular Stihl muffler bolt. It is the same removal method you use for a Stihl ms 1180, 250, etc. this is why I hit the oil and gas caps on my saws with compressed air or a paint brush before I remove them. Can’t keep everything out but I can get rid of most of it. You have to make sure the output hole on the pump is properly aligned with the hole leading to the discharge port. It is the small hole in the side of the pump. The imput side is the slot in the end of the pump. I clean out the oil and gas tanks with break cleaner on my saws at least once a year with break cleaner and compressed air.
@ismaelvalle9868
@ismaelvalle9868 Жыл бұрын
👏👏👏👏👏👏👏👏
@microfarmers
@microfarmers 3 ай бұрын
Brake kleen eats plastic and rubber, use WD-40 or soap and water and compressed air.
@AndyGenova-jr9ol
@AndyGenova-jr9ol Жыл бұрын
Could have just bought new kit half-assed repair o well u work with slingblade wheres my cousin vinny
@THEMOWERMEDIC1
@THEMOWERMEDIC1 Жыл бұрын
😂
Stihl MS250 Not Oiling?   How To Fix A Chainsaw If It Won't Oil The Bar And Chain!
31:28
Married with Small Engines
Рет қаралды 17 М.
1% vs 100% #beatbox #tiktok
01:10
BeatboxJCOP
Рет қаралды 67 МЛН
小丑女COCO的审判。#天使 #小丑 #超人不会飞
00:53
超人不会飞
Рет қаралды 16 МЛН
Try this prank with your friends 😂 @karina-kola
00:18
Andrey Grechka
Рет қаралды 9 МЛН
Get The Most Out Of Your Chainsaw In 2 Minutes With This Simple Task
5:52
Steve's Small Engine Saloon
Рет қаралды 140 М.
TOP 5 MOST COMMON ISSUES I SEE WITH THE STIHL 4MIX ENGINE
12:50
THEMOWERMEDIC1
Рет қаралды 61 М.
STIHL HT-KM Pole Pruner Cleaning Maintenance
12:31
RJL Gardens
Рет қаралды 22 М.
How To Fix A ChainSaw If It Won't Oil The Bar And Chain
6:46
Steve's Small Engine Saloon
Рет қаралды 568 М.
Сэнсэй и СИНЯК! inst: psawkin
1:00
Petr Savkin
Рет қаралды 105 М.
Её автомобиль никто не хотел ремонтировать!
20:12
Гараж Автоэлектрика
Рет қаралды 1,5 МЛН
Разогрев водителя
0:16
yanapozitive37
Рет қаралды 227 М.