Strymon Iridium w/ Midi Is Incredible!!

[@itengineer9535]

More videos like this! We electric guitar players need crayon diagrams to understand midi. Thank you for making this very informative video.

[@GoodwoodAudio]

this is really helpful feedback, thanks! Love the crayon diagrams... I'll go to walmart and pick some up.

[@MusicManney]

😂

[@xcomadrejax]

you just fixed a big issue i had with my iridium, THANKS A LOT!!! great video.

[@GoodwoodAudio]

awesome!

[@me-yg6yk]

this is the best video about strymon single jack midi device - pbc/midi control... been trying to get presets saved on pbc 10 a few hours and no luck , until I found this video , thanks . Also the bypass control is life saver , turns out my sunset wasn't on midi channel I assigned to, so I fixed that too!!

[@GoodwoodAudio]

glad it helped!

[@TeleCustom72]

Mind blown!!! I have the Iridium and was hoping that the MIDI control would be this powerful. I'll be looking forward to incorporating all of this with my other pedals.

[@GoodwoodAudio]

I honestly was pretty blown away making this video as well... So much more you can do / applications you can use it for than I originally thought.

[@ReyYbarra]

Thanks so much for this video guys!

[@GoodwoodAudio]

Thanks for checking it out!

[@bastilang1305]

Hey there. Nice Video. Which cable did you use to connect the iridium? Regular TRS cable or some midi adapter. Is there also a way to change amps via cc? I am thinking about buying an iridium to use with boss es5. Thank you 😊

[@GoodwoodAudio]

thanks for checking it out. I used a TRS cable with an isolated midi box (like the Morningstar Midi Box that converts 5 pin DIN to TRS but is isolated. Strymon also makes a cable that isolates the signal as well for about $30 or so! You can change amps and cabs via midi, yes!

[@adilsonobelard9690]

I am holding the 2 Stomps and blink very quick the red lights and them the lights turn off

[@carlodigilio2792]

hello, thanks for your valuable advice. I have a question, probably very trivial, but I'm a newbie in midi programming. I have an iridium that I control with a musicomlab efx le II switcher. the question is, does the iridium need to be plugged into the audio loops of the switcher as well? change anything between midi-only connection, midi + audio? thanks, I hope I have explained my doubt well.

[@GoodwoodAudio]

If I'm understanding you correctly, you do not have to put Iridium in a loop of your switcher, no. You can use midi to bypass it when you want to use amps or turn it back on / adjust settings etc. Lots of midi control with iridium!

[@jonischuster]

Hi!! Can I buy any midi controller and my Iridium will read it? Thanks for the video is very complete!

[@GoodwoodAudio]

so long as that Midi controller can send PC's and CC's on a specific midi channel, yes. Some midi controllers dont' give you much flexibility here, but a lot will. I'd recommend Morningstar or Pirate Midi for basic midi controllers with lot's of flexibility Or RJM Music for Midi controllers and loopers in one.

[@jamiefloate107]

Do you think it would be possible to control both the iridium and a separate midi compatible FX unit (like an MX Stomp) with the same midi controller? The iridium has no midi out so would you go to the FX unit first, then midi out to the iridium?

[@GoodwoodAudio]

you definitely can, but you'd either want a midi splitter (like a quadra thru) or just run HX first, then a strymon opto midi cable to the iridium midi in from the HX midi out.

[@jonathansilver4513]

When Iridium is bypassed, can you play through an amp as you normally would? Is the signal affected at all?

[@GoodwoodAudio]

you can! Not affected anymore than a standard bypassed pedal in your signal chain

[@joeguitar7164]

Hi, what cable do you use? midi-trs type a or b? Cannot find anywhere what I should use....

[@GoodwoodAudio]

Midi A - but you also want to make sure your midi chain is isolated for strymon 1/4" pedals!

[@joeguitar7164]

@@GoodwoodAudio thanks a lot, much appreciated! Still figuring out how to get i to work though, what do you mean exactly by 'isolating the midi chain"?

[@joeguitar7164]

after numerous attempts i bought the quite expensive midi-1/4 trs cable from strymon: everything works fine. there's some electronic moyo goin on inside: you cannot measure any direct connection from one side to the other. May be older versions of firmware did work with trs type A, but my iridium did not!

[@GoodwoodAudio]

@@joeguitar7164 the midi inputs on strymon small box pedals need to be optically isolated. That's why they made Conduit. It prevents ground loops / noise issues when running multiple pedals like that.

[@sammyfujimaki]

Is that free software from Strymon?

[@GoodwoodAudio]

yes! you can check it out on their site and the PBC editor on the RJMMusic website

[@garyclements6946]

Can I use the RJM Software with a Boss ES-5?

[@GoodwoodAudio]

Unfortunately they aren't compatible. Would be awesome if they were though! Never thought about that. Good question.

[@garyclements6946]

@@GoodwoodAudio do you know of any editing software for the Iridium?

[@garyclements6946]

@@GoodwoodAudio maybe I should ask....what kind of switcher is that in the video that has software that allows for the creation of Iridium Presets?

[@GoodwoodAudio]

@@garyclements6946 That's the RJM PBC (a midi controller / looper). Since it's midi you can access presets you've saved ON the Iridium and access other features on Iridium but you can't 'create' sounds on Iridium.. Sounds like semantics, but the midi controllers can only access what is already there rather than create.

[@garyclements6946]

@@GoodwoodAudio thanks! I would really be great if Strymon would get an editor for Iridium.

[@Tvaroh]

Thanks, very nice and useful tutor! Just the music and voice level are very unbalanced.

[@GoodwoodAudio]

Thanks for the feedback Alex. Ya - agreed. Im learning as I go and have adjusted this since this video.

[@lawrencebrooks7231]

TURN DOWN THE GODDAMN MUSIC JESUS

[@GoodwoodAudio]

You sound like me as soon as I turned 30.