This Cast Iron Pipe RUINED Our Work Day.. Rough Plumbing BEGINS! - THE SHOP Part 2

[@jkrzaczek]

Guys, I'm a software engineer from Poland (that country next to Ukraine). I have nothing to do with home remodeling and anyways we build houses very differently over here (brick and mortar). I watch your videos anyways, cause you guys are great and it's a pleasure to see a Team like you do an awesome job. Thank you!

[@drdarwinator]

“That Country next to Ukraine” lol 😂

[@desireeespinosa3954]

Thank you for supporting The Stud Pack and Ukraine Poland 🇵🇱🥰

[@mattcraztex9940]

@@drdarwinator Few Americans really know Europe so we specify so you know in case you didn't.

[@drdarwinator]

@@mattcraztex9940 As an American myself you’re pretty much correct. I’ve got family from Europe so that does help quite a bit.

[@Paul-hl5ls]

A chain bolted around the pipe with a jack under it will lift that right out.... I prefer a farm jack also called a trail jack and I pull concrete set post with it

[@HisboiLRoi]

I'm guessing the double sanitary tee (first shown at 15:40) was used because it allows a straight shot on the two vanity branches. However, most codes prohibit san tees for horizontal to horizontal direction changes. It certainly would fail inspection in Tucson where I am located. Stacking opposite facing combos (or wyes with 1/8 street bends) one after the other is universally acceptable. Many jurisdictions would also allow double combos (or double wyes with 1/8 street bends). Obviously, these solutions would cause both 90 degree branches to overshoot their targets, but a 1/16 or 1/12 bend would easily get each back on course. I don't know how that would affect the plans for the floor framing.

[@mcarroll598]

Should’ve just cut the floor where needed for the plumbing. I know your buddy was worried about dust, but the appropriate temp wall to catch dust and lots of water would be well worth it. Oh well!

[@lordginger636]

Yea I feel the same way. It seems so dumb to do all the for a nice bathroom shower and then have to step up 6in to get in it like maybe it won't be bad if they make a ramp going in but I'd much rather have everything lever with the rest of the shop floor

[@mcarroll598]

@@lordginger636 yeah definitely, I am a commercial/industrial electrician and have been in the trade over 24 years and have done a lot remodels. Have seen the floor cut a lot for plumbing and or electrical. I actually worked on a Dialysis center remodel and it was in 3 phases while the building was occupied. And they saw cut the floor many times for the remodel. Not much dust at all the way the contractor did it.

[@clintprice2123]

A large fan in a doorway or window to exhaust the dust particles helps too. It would draw it away from his cars and other things.

[@rogermccaslin5963]

Yeah, I thought the same thing. A wet saw and there's no dust. And you can clean up the slurry created before it dries to keep that from dusting up when it dries. They did okay with the circular saw and water. A proper concrete saw is basically just a bigger version.

[@outlet6989]

I recently bought a pair of extendable poles that reach the ceiling. They're made by a company called Third Hand. They sell an attachment made to hold a piece of plastic from floor to ceiling. The plastic has a zippered door. I've used these many times when doing DIY projects. No dust, no pissed-off wife.

[@straight_to_finish]

Gentlemen-I like raising up the floor as oppose to jackhammering out the slab. One issue that I noticed that others have mentioned is the use of a cross tee in a horizontal orientation. (This would not pass in my jurisdiction). In that position, it can not be used for drain or waste-only vent. What you should replace it with is a double wye + some 45’s. There’s not enough sweep to force the waste to turn 90°, plus if you were to ever snake it, it would shoot straight across. any change in direction in a horizontal position should have a long sweep to it. Otherwise, fantastic job as always!

[@dollyhadbraces9361]

upc maybe , internatioanl a 2" can be flat..

[@stephentucker5406]

Will not pass here in Ohio too Or NPC Just think of it as all waste turns have to be long sweeps ( no sharp 90*)

[@poopandfartjokes]

Should that double L he’s putting on top of the slab be a cross instead, to vent the stack?

[@greghight954]

I was thinking the same thing.

[@alexstoles1339]

Yes if that ever cloggs up they will be very lucky to get the snake to make that drop

[@daveyfrost7114]

A GFCI measures the difference in current between your hot and neutral prongs in the outlet. No grounding required. In fact, when replacing outlets in a house that does not have a grounding system, NEC requires those outlets to be replaced with GFCI and labeled "No equipment ground". Using a double insulated tool should not be an issue.

[@waliw3841]

My understanding is that double insulation means the cord and body are separated from continuity meaning there is no chance of residual current on the cord to the receptacle, so gfci would not work in the case of a traditional ground fault. This separates the user from being the dangerous path to ground/neutral while working in a wet situation.

[@jeromegarcia5396]

Does this apply to battery packs? A blonde question probably, but I'm not much a electric guy past the breaker box of a house, I respect electricity so much I don't do more than 220 because 220 can kill you, so can 110, but that is scary enough.. Pretty sure you'd burn through batteries trying to cut for that long of time in cement, probably burn any brushless motor up too... I don't know, I'm more cave man at 240 plus and would of hammered it without precuts, but I have seen the method used before as I was the water sprayer thinking huh, all be damned...

[@daveyfrost7114]

​@@waliw3841 I'm interested to know how it wouldn't work? If the current leaving the outlet, traveling through the load and returning are not within a certain tolerance - typically 4-6mA - then the device assumes a ground fault is taking place and trips, opening the path.

[@TwilightxKnight13]

Agreed. Most people do not realize that the grounding wires and neutral wires are connected in the vicinity of the panel/meter and are essentially both "grounds." Understanding the difference between "grounding" and "grounded" is generally what separates an electrician from most DIY'er. There are a lot of ways electric will work, but that's not the same as doing it "right" or to code to protect the equipment and the user.

[@daveyfrost7114]

@Robert Swaine That's definitely a much simpler way to explain it. Thanks! I'm used to talking to other electricians all day, hehe.

[@margaretbear]

Hey Jordan, just want to give you props for all you have done. Your Dad gets a lot of the accolades (rightly so!!), but you deserve major kudos for all you have done and do for your dad and for the channel. And Paul, damn, you are a powerhouse. I'm so impressed with your knowledge, enthusiasm and energy. I get tired just watching you work.

[@debo1211]

Can’t stop this Father-Son duo!

[@outlet6989]

What I really like to see. A father and son passing the trade and working together as a team.

[@kailashbtw9103]

They both do incredible work!

[@JackGiralico]

Dynamic Duo. Never cease to impress.

[@Ontimecontractors903]

Food for thought next time youre connecting pvc to cast with the inner rubber. Measure and mark a refrence line on the pvc indicating the depth you need to go. That way once its in you wont have to remove it again.

[@terrytrzecieski1750]

When demoing out concrete floor, I use a 1/2” masonry bit, make Swiss cheese out of the floor, then chip it out! Works great concrete comes out in chunks Same roto hammer drill Also bought a 60lb roto hammer from harbor freight, 300$… I use that when I’m doing curbless showers

[@greghight954]

That was my first thought on how to do it.

[@RehabLife]

I'm a purist! I would have removed the concrete even if it meant using a wetsaw and jackhammer to keep the dust down. I might have even brought in a low flow hose to keep the slab marginally flooded. I know ... expense, time and labor ... gotta make choices to fit the project into not only the monetary budget, but also the time frame budget. Can't wait until to see what is in store!

[@HighPeaksHome]

As a non plumber remodeler i enjoy your diversity in skill sets. One helpful hint i would give though is ditch the Milwaukee blades and go with the diablo full carbide for cutting steel, they last much longer and cut faster. Cheers!

[@natej6671]

Great progress guys. Paul, I wish you could have twisted the shop owners arm a bit more because I think demoing the slab would have been the right move. With copper lines that old, I'd replace them for fear of having thin walls and getting a pin hole leak in the near future. Also, creating a platform would make the restroom unfriendly for handicap access. BTW isn't a 2x6 lumber 5-1/2" tall?

[@Aepek]

16:13 Ya would think that right, but was demoing an old historic house that was previously remodeled and not only were hot/cold lines reversed everywhere, but whomever installed that cross you have, did indeed install it “backwards”….or “opposite flow”.

[@johnpeters9903]

As a retired plumber i got a few laughs from your job. a saw cut would have been the right way to build that bathroom. The 3x2 cross laying on its side would not pass inspection in PA. With soil pipe, the gasket always goes in first.

[@taliotero78]

Hi Guys, You guys do amazing work. My humble recommendation is the Doble TEE I would swap it for a Doble Y, I don't know the codes there but I think will be better.

[@DCDLaserCNC]

You and your son make such an awesome team! Love seeing the father son bond you two have. You guys are not afraid to tackle any project. Keep up the great work!

[@delawareindian]

Been frabricator 45 years,wood, steel, tin,decks ,bathrooms,additions. Seen alot of vids,but couldnt stop watching both of you. The kid helped and was upset for not beeing on video showing his effort,( very impresive). Very infomative and liked the banter,( just as in real life). Hope to see you again,when looking for info and guidance. Im replacing old cast iron toilet flange(50+plaster walls)need to smooth out inside rust so the expansion hub will seat in old rusted cast iron. Any suggestion would be greatly appreciated. Keep up the good work guys hope to see you soon thanks

[@Pepe-dq2ib]

go to home depot and rent a rigid soil pipe cutter for $12. It technically doesnt "cut", but snaps the pipe and pops the cast iron just off.

[@briansegall1084]

I opened my concrete slab to modify some plumbing last month, and I had a laugh at your bit getting stuck in the concrete and the struggle to get it out. Happened to me more than once! Good times.

[@stevenpike8895]

The twin tee (short turn fitting) was the wrong fitting for this application. They should only be used vertically in drains. In venting they can be laid on their side. When laying a fitting on its side in drainage you should always use a long turn fitting, in this case a double combo.

[@michaelmartin2989]

Would use a combo and a wye downstream with a 1/8th bend if u want the centers to line up

[@FaceFaceMan]

Just curious, would his set up pass inspection? (Does the remodel work require inspection in their county?) I'm genuinely curious based on what little I know about rough-in from being a flunky years ago.

[@dropletz.]

@@FaceFaceMan it depends on where you live but around where I live none of what he did in this video would pass inspection.

[@joshcowart2446]

@@FaceFaceMan it wouldn’t where I’m at in Austin tx. They’d make you get rid of the cross fitting and stack two combos instead. They won’t let you use double combos because the idea is if you slope one side it puts back fall on the other. I say just lay it flat and slope the pipe and you’ll be fine but that’s what they require.

[@plumbbuild6517]

@@joshcowart2446 that makes sense but here in Georgia I’ve passed inspection with double wye because you can slope the street 45s Slightly. But that double santee would never pass.

[@johnnybussart4721]

Exactly correct. GFCI measures an imbalance between neutral and hot...soooo many dont know this.

[@margaretbear]

Yeah, if you needed a ground prong for GFCI they wouldn't work on hair dryers.

[@MrJrston]

i found it handy to drill couple of holes into the concrete, so the rocks would have space to move when chiseling

[@chadwickhayes8260]

Drill a perimeter that’s how giant holes are made in concrete walls

[@KaraBaker-ux3wr]

Love it! Exciting new project series. I started with the oldest series and I am working forward. I’m so enjoying the evolution, the process and the projects.

[@lenhanson6719]

Deburr, bevel one side but not the others? Get a Reed Deb4 if your gonna run some pipe. Otherwise you're not doing it right since the edge is scraping and pooling the glue towards the inside of the fitting instead of spreading as it should.

[@wat3rdog25]

For things like that CI pipe, try a Hi-Lift farm jack. Wrap a chain and jacks right out. Great for cemented post. I also found it works great for huge stubborn concrete pads. Lift the section of pad up and toss something underneath for a void and pop away with a sledge. I came up with that one demoing my pool.

[@92sportster26]

Just curious if you have to have a plumbing inspection before you cover that plumbing

[@ArthriticThumb]

Have you heard of the Aldrich tape measure. It’s a 25ft tape but the inch is broken down into decimals like the metric system. I found it on Amazon it’s really cool

[@alexoden8920]

Let’s go!!! Can’t wait for the Texas house Reno!!!

[@StudPack]

We can't wait!

[@dapv144]

I had a similar demo around a pipe and what I found helpful was to use tapcon (concrete screws) into where I was removing. Every 3 or 4 inches screw in a tapcon and pull it out. It helps break down the concrete into sections and makes it easier to control how much you remove. P.s. I'm a rookie and you guys are awesome with these videos. It's greatly appreciated guys.

[@charliekman]

They make an adapter fitting to use in a cast iron bell gasket not sure if it's code where you live but it is where I am. Sure it wouldn't be a problem just might make it easier next time.

[@jeremycovelli]

Not sure if you guys had a torch or not but I would have torched that rubber.. just need to do one spot for about 30 seconds and the pipe will come right out. It's actually suction rather than friction that makes those stuck like that, torching the rubber and melting it a bit breaks the suction.

[@damonhughes325]

Paul, instead of using soap check out 3M 08946 Clear Silicone Paste. Great for all kinds of applications, just make sure you don’t apply it to anything that you want to glue/cement or don’t want to be slippery.

[@MRVinydf]

Hey Jordan and Paul! I think the problem with the mic is that it is being clipped inside the shirt? Not sure, but I got some shots there that it looked like it was inside and hot outside. Worth testing to see if that fix the mic issue. Cheers!

[@johnpiegzik298]

I love the channel guys I found you guys from the Perkins builder Brothers and I really enjoy your channel! Love the build keep up the good work!

[@ardendolas]

Stud Pack videos are always a highlight of my day. You two look to have a great working relationship, and I’m always learning tons watching you guys. Keep ‘em coming!

[@MAGAMAN]

As long as you only view them for entertainment. Don't expect anything these guys do to pass code inspection.

[@Dregg0]

What I love most is how joyful you look while doing grueling work. It's easy to forget that joy when you're in the thick of it, especially when things aren't behaving the way you'd like them to, hahaha. Thanks for making it look not only possible but a source of joy!

[@CircleCityPlumber]

That double fixture fitting wont be able to be cabled downward in the future as the cable will cross over to the other side. This can also cause damage to the opposite side bathroom because a future plumber won't know that the fitting is placed like that. It would be much better to use a double combination, this way the sweep would ensure that the cable only goes downstream. It also wouldn't be too hard to expose a little more pipe in the ground and install two Wye fittings.

[@digi3218]

You make a good point.

[@livinb450]

You guys are great! Love the Dad Son thing, and all things building. Congrats on whatever success you are getting. Thank you for your content. You guys make my life better!

[@whattheschmidt]

The one part of this build I would never want to do is breaking out the old drain low and putting in new connections. Redoing my bathroom and connecting to the PVC 'tree' in my basement with a couple connections was aggravating because if anything didn't fit just right and I messed up near the tree, there would be a ton of cut out and redoing! Great work and I'm glad this worked out with that rubber seal nicely. I thought it was going to be a difficult cut down low.

[@ShannonGraceM]

Nice work around the cast iron. I've been thinking about digging down my basement for a 10 foot ceiling for a proper addition and seeing the concrete fall away from the iron was good to see. Stay safe, stay happy, and stay sane while you can.

[@daviddinkha2811]

Looks great 👍, but yeah should have cut the concrete with a rental wet saw. No dust, and probably less costly compared to the price of lumber right now. Pressure treated lumber prices are ridiculous in California not sure about your state.

[@bread-gz3rl]

Oh god the old dewalt 18v, haven't seen a good one of those ever

[@mcgeorgerl]

Those rubber "donuts" that connect the PVC to the cast iron can be a pain. There is no "standard" bell ID and different pipe manufacturers set their own standards. It really didn't matter back when they were using lead/oakum for the seal. For a given cast iron pipe size, the local stores like Home Depot and Lowes only carry the one that's the most common pipe diameters. It just so happens that my house built in the mid 50's uses a different donut than either of the 3 home stores in my area (HD/Lowes/Menards). Before you go ripping the plumbing apart, you better have plans 'B' and 'C' ready to go. Know where your local plumbing supply house is that sells to the pros. When the one from Home Depot doesn't fit, you can get the accurate ID of the hub you're working with and there's a good chance the pro supplier has the one you need. Make sure they do over-the-counter sales before you make that drive. If you have to order on-line you can expect a couple of days delay in the project. Also, make CERTAIN that the cast iron pipe is fully supported before you wail on the PVC with a sledge to drive that into the bushing/donut.... If the pipe is not supported, you can crack the pipe or damage the next lead/oakum seal in the pipeline.

[@jacksplumbingvideos7147]

You used a tee on it's side, that needs to be replaced with a double wye.

[@jamesdk5417]

Hi, a bit of heat shrink over the strain reliefs of the mic cables may help with them cutting out.

[@stephentucker5406]

Those connections are meant to be locking joints. You need to cut the pipe and use a furnco band clamp ( stainless and 2 strap type)

[@ThaGreatestAlexander]

Have you guys checked the rated RPM for that diamond disc vs the skillsaw? the diamond disc has to have a higher number than the saw. Typically people get this wrong mixing and matching zip-cut discs or cold cut discs.

[@dankelley9361]

Another excellent YT video! I wish that the cast iron was leaded in instead of with that rubber bushing, only so I could see how you’d tackle that. Looking forward to seeing the transformation to a beautiful bathroom! Thanks

[@buck3006]

I work for a demo and tile removal company, that Bosch hammer is my favorite tool ever lol

[@lizzethtres7503]

Really enjoyed it. Love the comments and explanations. Thanks for sharing. May God continue to bless and protect you and your family.

[@agray8109]

City inspector have any problems with your plumbing and/or platform? Bathrooms ADA compliant? 😃

[@ThaGreatestAlexander]

I like to run a shop vac next to the jackhammer during chipping to catch some of the dust. you guys do great work we all just learn different tricks as we go, safety is big in my company

[@martinp1544]

I jackhammered a lot of tile for my house. The noise was LOUD! So I wore double hearing protection. Foamy ear plugs & ear muffs to save my hearing.

[@jimdavis4356]

Why you didn't cut and jackhammer the floor for the new pipe and drop it in so everything is level with existing floor? Having a step up into the new bathroom sucks, this one will be at least 6" or more? I've jackhammered alot of concrete in that climate, put in the sweat and do it right.

[@suzannepuckett2245]

I’m so grateful to see that. One people still take pride in their work ! And someone who knows what he is doing! Lookiniig forward to welcoming you to Texas! I live on the coast,but I’m willing to help y’all anytime!

[@Palpatine4Senate]

I'm really excited to see how this turns out. I'm so glad I found your channel. Edu-info-tainment at its best!

[@josephmirowski371]

Can you show in your next video how you get the correct slope on the pvc pipes. I guess the pipe connections allow for a little angle too.

[@Gnuuhh]

Hey Stud Pack guys! I've only done a moderate amount of work like what you do on your channel and I mostly have no clue what's going on. But! I'm really loving the energy and enthusiasm you have for your craft. Watching your videos over the last week or so has shown me what happens when professionals take pride in their work. You guys not only make it fun to watch, but when you finish your projects, you end with some incredible works of art! Some of your projects are beautiful to say the least. One that comes to mind immediately is the microwave you installed in a kitchen cabinet that ended up with a small drawer added underneath. Not only was it incredibly informational, but it also felt like you loved showing all of us how and why you do what you do. That can be said about pretty much all the videos I've seen! It's easy to tell you enjoy what you do and that passion radiates throughout your videos. Keep up the good work and I look forward to seeing more :)

[@johnds6621]

interesting you cemented in the floor already. No Plumbing inspections? You not going to wet vent a toilet or was your plumbing layout just for seeing how it fit on the floor?

[@billytyson1748]

I like how you explain what you are doing and why. It is very informative. Thanks.

[@AlexanderPage2022]

Just finished 2 hours of working on muddingw drywall in my basement and came up to this video. Sweet. Thanks for all the great content.

[@83delgado]

Hammer drill lots of shallow holes around the drain. Then chip away. It saves time and our backs.

[@geraldfrench8137]

Could not tell from video but if your copper was not sleeved I would have done so . Concrete and copper especially after fifty years can cause electrolysis to set up and leaking copper. Only possible if copper went under slab .

[@mrbig4532]

If you would of spun the four inch cast iron as you were prying up that would of came out a lot easier. But I’ve been a commercial/industrial plumber for 30 years so I know a lot of the tricks that get us thru the day. Also when putting the new pipe into a existing hub always put the tyseal into the hub first then lube the end of the pipe and inside the the tyseal , then if possible use a bar to push the new pipe into the fitting.

[@jerryminyard7460]

I had the same Schick. It was the best. It was my grandpa's from a long time ago. It was stolen from me in 2004.

[@williamevans6522]

The proximity of the iron pipe to the copper just complicates the concrete created corrosion with a galvanic corrosion component from the dissimilar metals.

[@mattwilliamson1714]

Another fantastic video! While it would be very simple to insure there'd be no dust from cutting the concrete, I also like the way you're doing it. Will definitely be a faster overall install for the customer, but will also enable the large super-awesome restroom to be easily removed &/or repaired in the future.

[@djkompressor]

Great work gang! Me and my dad had a project like that before! Framing the floor wasn't the most fun task but was definitely a learning experience. Especially maintaining your slope!

[@dennisbrown2571]

Hell of a bathroom for a shop. Vanities and a super shower! Where do I put in my job application? :)

[@hansangb]

Jordan and Paul...the poster children for "Dirty Hands. Clean Money" ethos. Love your channel and the chemistry. This and Perkins Builder Brothers are my favorites!

[@cjn2365]

Love stud pack they have helped me redo many things my my house. Thanks guys. Keepup the good work.

[@Matt-my7pz]

The linear drains are sweet. They aren't as easy as a typical on tho. One comment guys if it's Schluter, do not run your fingers along the inside of the stainless fittings. It's super sharp. Same with the cover. I had the solid stainless cover when I did it. I heard the waffle faced one collects hair on the surface. BTW that's funny but understandable what people say about the dbl insulated tool and GFCI. Glad you get the proper facts, I'm an electrician and you're right. Your guys filming and explaining is excellent.

[@rodpotts2666]

I pull steel post or chain link post with a pipe wrench and hi lift jack.

[@cooleyre]

Double vanities with the entryway to the shower located between them is a really cool design, looking forward to seeing how that turns out.

[@80Ragincajun]

Another Great Stud pack video!! Im working hard to get my Home repair and reno business up and running. I learn so many cool tips from you guys!

[@Aepek]

Man @Stud Pack you really sure do have the “cliffhanger” ending down 200%. Ya make it so not only do you draw ppl in w/ how both you Paul and Jordan interact, but how you guys work and the standards you have….which are high (very great imo👍🏻), and never miss the “details” which can break a project. Always a great job, fun time watching and “hanging” w/ you both….and leave us always JUST WANTING MORE MORE MORE! Well, till next time; have a great day/week. Here’s to you Both✌🏻

[@lewiskelly14]

Pretty low standards for audio quality

[@MegaDysart]

@@lewiskelly14 everyone's a critic. Where's your videos lewie?

[@felixamill5229]

The gasket it’s glue get your turbo torch and heat the hub, it will come out easy.

[@meganm3270]

Ascension parish here we have cast iron sewer lines under our concrete slab with the lead in the joints built around the same time as the one in the video. I hope I never have to replace them .well at least not anytime soon 😱

[@TheHcmedic]

I'm enjoying your videos a lot! Learning through them as well. Keep up the great work. By the way Welcome to Texas!

[@chetleonard169]

Sounds like you're sweating your mic out. ( muffled sound ). With a collar you can place the lav mic under the collar pointing forward and it should stay dryer. The cable runs around to the back and you'll have to poke alil hole for it to run through, so that the cable drops down the back under the shirt. Hope that helps guys.

[@envisionelectronics]

I love how you set the record straight about ground fault outlets without restoring to explaining anything. I wish I could be so concise.

[@arealmaintenanceandrepairl1103]

maybe drill a 4 inch square out so that way when you chip hammer it it will be able to have somewhere to break into then u can chip away from the edge.... pretty much drill with 1/2 to give you some release pressure when chipping and big chunks will fall out

[@robsmiley3188]

The porter cable and the water bottle It's the same concept as a wet saw I do the same with my grinder with a diamond blade and a wet sponge held on the blade to cut tile and concrete

[@jennywuornos5809]

Diablo blades and Milwaukee tools! Boys if you do business with Copper State Bolt and nut I can save you some money on all of that 🤓 especially with your new build coming up. Yes I’m a sales rep yes that was my pitch but I just enjoy y’all so much I would love to help your pocket books! Glad you helped Paul today Jordan. My husband and I were screaming at you on the TV to not throw your back out 😳😅

[@bernhardm9475]

You've got the most awesome bathroom planned. Even a urinal !! Just back from a visit to Europe, my spouse and I fully discovered the joy of clean with a bidet. Have you considered that as part of your utimate bathroom? You got room... Please consider it. As always you are all "must see KZbin" for me and many others. Thanks guys !!

[@tomjakobs328]

I'm a plumber by trade and I found a shick pipe wrench at a yard sale bought it right away ten bucks worth 1 mil amount of work it does cool?? 😎

[@utubehanna]

You guys absolutely earn a “like” every time. Thanks for another great and informative video!

[@aaronhill1229]

Double cross on the flat isn’t code. You would need to run a combo or a wye. And when you go to snake that you go up the other side.

[@Giggidygiggidy12]

Going 3in is there a lot more risk of clogs or things getting backed up? What does the fall need to be to use the 4in pipe for sewage?

[@wcvp]

According to my local plumbing inspector, 3" PVC fine for an entire house most of the time because of how slick the inside is.

[@xeress]

Would have been nice if you all could have wet saw the concrete in squares and then break them individually with the rotary hammer while the floor is still wet. Great Job

[@iwillburn]

You guys are awesome! Thanks for the posts! Looking forward to the future work and videos!!

[@jarrodwebster8166]

A combination tee or double y with 45s is a better joint than that cross. I would be very weary of back flow issues

[@arose1620]

This is a fantastic channel you guys! Now I just wish you two were closer so we could hire you to remodel our bathroom!

[@edreitmartinez9127]

Dont know wsne i saw one the first videos from your channel i saw but i love your work need more people like you who love what they do not just for money😍😍

[@robertjagger3513]

Have the exact same Shick aluminum pipe wrench.

[@tonyluna4445]

Enjoy your videos. Curious, how are you able to fill in that little area of concrete without it being inspected? In Florida, we can not cover anything especially under concrete without inspection and leak falloff testing.

[@brandonleonard9135]

Just got around to this video guys Paul your friend had a very interesting shop!

[@mattblah7737]

gasket firs, then the pipe. the gasket doesnt go on the pipe. It goes in the hub first. The gasket you used is a mult tite, which is always a pain in the ass

[@brioshoveit]

Do not forget to add protection for the frame and ventilation. Great vid as always, even if it was some problems with mic (as mentioned in the video). Stud on!

[@terenzo50]

Had my doubts at the very beginning, but you did it! My amazement seems to continue along with your work!

[@josephhinson7553]

Do you not use PVC cement,just primer? Or did I miss it?

[@Jeff-xy7fv]

Great video! On your next one, please show all the electrical work being done.