Bạn hiển là người rất sáng tạo sẽ đạt đỉnh triệu like
@mihailmokin81474 жыл бұрын
варить корпус подшипника! это "революция " в технике
@F15rocker4 жыл бұрын
Hand held precision drilling. What a guy. My hero :)
@Evangeline-Katherine4 жыл бұрын
Built me a small cart with these where only one person could ride in,,,, see how fast it would run,,, 😊😊🙋
@huywrquoc10274 жыл бұрын
Mối hàn ở chổ bi bị hàn sợ chụi lực ko đủ! Có lẽ bạn nên cho 2 ổ bi đó vào cái ống sẽ tốt hơn.
@lmp22084 жыл бұрын
NFI, ha ha. Welding a bearing outer casing with the earth clamp on the shaft. Should last a couple of hours of usage. 😀😀
@tranmanhcam60604 жыл бұрын
Cưa mỏi tay luôn
@grandmaster-grouch4 жыл бұрын
hey bud try coming down at a 30deg angle on your stick welder. i discovered better puddles. cheers
@ianbox134 жыл бұрын
be better using a vice and far safer. Drilling a hole with your hand behind the workpiece is just asking for trouble.
@ksthacks4 жыл бұрын
hi :)
@THEPAINOFITALL4 жыл бұрын
That’s good ADVICE...lol😝😛😜
@CChironCentaur4 жыл бұрын
I don't know about other viewers. When I watch this I just see how lucky he was not getting hurt using all those tools the wrong way or with no protection. Drilling in to your hand, welding with out gloves. placing the ground on the shaft of the bearing your welding(could have welded your bearing). holding a part your welding with a bare hand.
@jeremytravis3604 жыл бұрын
I was thinking, push hard and drill a hole in your hand. Breath in the zinc fumes. A bit of arc eye anyone. Never mind I will have good swig of bleach for breakfast.
@pauldogon48314 жыл бұрын
Randy while I can see where you are coming from, in the less developed parts of the of the planet it is a case of just get on with the job. I am 58 and still have all the bits and pieces I started with, minus several teeth and some brain cells
@pablomtynl3 жыл бұрын
Hello, excellent idea, where did you get the engines with their starters that you remove first to put the two 775 engines?
@sonnyburnett55144 жыл бұрын
An interesting project. Those 775 motors alone have some pretty decent specs. for their size so with that additional attached gear reduction (WHY DO YOU REFER TO IT AS A ''STARTER''???), the additional torque is handy. Would you mind informing a fellow ''HACKER'' (I consider myself as a ''TINKERER'') where you found these 775 gearmotor assemblies? By the way, you really should invest in a few more tools like a vice, a grinder with a cutoff disc & an inexpensive drill press with a vice . Again, an interesting project.
@paulpercie28174 жыл бұрын
Tried building this myself but I couldn’t find a pair of crocks
@JodBronson3 жыл бұрын
LOL 😂❤️😂❤️😂❤️
@johnharvey4life2 жыл бұрын
Those ain’t crocks they’re state issue jail house shower shoes
@nikk31794 жыл бұрын
Nice..u can build it more..like you can do a tiny war tanker🤗
@tathan4273 жыл бұрын
Như vậy là qua 2 giảm tóc củ đề rồi qua thêm giảm tóc xích nữa
@ManollPetualang2304 жыл бұрын
Wow nice
@ksthacks4 жыл бұрын
So nice
@KamranKhan-by5mc3 жыл бұрын
Excellent
@ksthacks3 жыл бұрын
Thank you so much 😀
@ritaisabel86654 жыл бұрын
Good
@ryanb18744 жыл бұрын
Ueah, powerful for short periods of time, otherwise they 'll get trashed.
@miguelafrican6484 жыл бұрын
Cuida tus manos
@ОрвасДрен4 жыл бұрын
В любой непонятной ситуации приваривай подшипник
@BHARWAD_boys_81824 жыл бұрын
Make a gear motor with simple pieces
@TheKrausdog4 жыл бұрын
Hands, feet, crocks... Mightier than the vice!
@yatra73124 жыл бұрын
How much rpm of this gear box
@JodBronson3 жыл бұрын
Just buy a bigger motor! 😂❤️😂❤️😂❤️
@ksthacks3 жыл бұрын
I do not have enough money :))))
@MdShahin-pz8kc2 жыл бұрын
এটা কি বিক্রি করেন ভাই
@nin1ten1do4 жыл бұрын
welding bearing.. my bals.. it hurt..
@kimnielsenthewordyvikingett1592 жыл бұрын
Is it that easy to change direction just change polarity????by the way love your little machine pretty darned smart 😉!!! Now put it on top of the front wheel of my bicycle 🚲. With a variable thumb trigger throttle and I'll give you a gigantic smile 😃😊🙂😀. Chain ⛓drive of course.
@naum9002 жыл бұрын
Do you get a gear ratio because the middle gear is bigger or is it the same speed as the two motors?
@goodidea10134 жыл бұрын
Wow! Really well thought, bro! Great work!!! 😃
@ercancit41963 жыл бұрын
bu motor 775 den daha mı güçsüz?
@luuthichuyenluuthichuyen84003 жыл бұрын
Loại như này bao nhiêu shop
@luuthichuyenluuthichuyen84003 жыл бұрын
Có bán bộ như trên vi đeo ko .
@elenaivanova4523 жыл бұрын
[power electric motor]]
@Fpvfreaky4 жыл бұрын
I think you need to invest in some steel toe cap flip flopps🤭😁 I got worried that blade jumping on your big toe 😰
@АлександрАйлбибэков4 жыл бұрын
Искры прям в глаза летят
@stuartodell17094 жыл бұрын
Interesting project. Don't you ever try to clean up anything (dirty internal gear housing, sloppy welds, sloppy joints.) and could you please cut the music?
@DSB.TecnologiaMaker2 жыл бұрын
Rodou liso, más porque não fez o reforço do outro lado ?
@anushaananth26003 жыл бұрын
Why did you change armor of the moters
@josenildomachado15243 жыл бұрын
which drill is used?
@vsnrchaitanya34944 жыл бұрын
Sir finally I'm asking one question that is what is purpose using this gare dc motor
@joecruz48463 жыл бұрын
What song is this ??
@asifbuttt4 жыл бұрын
Your hands working nicely but hand drilling can give you lesson. Note my point. Be safe
@absubandi70293 жыл бұрын
Om beli dinamo unti.ukspeda d mn ya om.
@davidf.84974 жыл бұрын
1.40, It's not hand-made but foot-made ;)
@ksthacks4 жыл бұрын
why not? :)))
@davidf.84974 жыл бұрын
@@ksthacks Just a joke because you're much holding with your foot ;)
@bharat43704 жыл бұрын
How much for this
@viethungle4064 жыл бұрын
cấn phải học hàn thêm, hàn không chắc, cường độ dòng điện đặt quá thấp, dính que hàn
@eurisespinosacandelario95453 жыл бұрын
Hung Le. Animate y haz videos enseñando a soldar básico .
@ausielad14 жыл бұрын
Good job mate, dont worry about all the other dick heads on here commenting, you used what you had and turned out fine, it works that's the main thing,Just be careful.
@MuhammadDaudkhanTV1004 жыл бұрын
Nice 👌🤘👍👍
@ksthacks4 жыл бұрын
thank :)
@jameswitte51674 жыл бұрын
What were the original starters for ?
@johnbravo75424 жыл бұрын
car window wiper motors
@jameswitte51674 жыл бұрын
@@johnbravo7542 so not really original starters ...
@sonnyburnett55144 жыл бұрын
@@johnbravo7542Hey, thanks for IDing these ''starters''(???). I've seen other videos from this guy & I was wondering what or where these ''gearmotor assemblies'' were scrounged from. Why he refers to them as ''starters'' is odd, but whatever. Are these used or can be found in most vehicles today or are they only used in certain makes of vehicles? At 58, I've been a ''born & proud scrounger'' my entire life so by now, I've accumulated a large inventory of STUFF in my basement I tinker with, but I would like to ''scrounge'' some of these. Thanks again for the info.
@CuongPham-il8ee3 жыл бұрын
có cần ic để dùng tay ga k b
@ksthacks3 жыл бұрын
cần nhé Cường
@CuongPham-il8ee3 жыл бұрын
@@ksthacks dùng 3 motor thì cần mấy ic ạ
@pratikpatil18734 жыл бұрын
Can I buy this
@manuelverdugo99554 жыл бұрын
No entiendo el porque ahora estan usando esos viejos motores que son muy ineficientes. la tecnología brushles es mucho mas eficiente y el costo es muy parecido. Mas el ahorro logrado en peso. Porque el esfuerzo para adaptarlos me parece mucho.
@eurisespinosacandelario95453 жыл бұрын
Se consiguen con estas potencias. Donde? y supongo que se usarían targetas controladoras o no?
@manuelverdugo99553 жыл бұрын
@@eurisespinosacandelario9545 claro que si. los consigues en cualquier tienda de aeromodelismo. para una bicicleta te sirve bien un motor 5065 con 6celdas y un controlador de 80A. esto te limitaria a 1760 watts. con una eficiencia de 70% un buen proovedor sera Hoby King( es en China)
@venkateswarlutatikondala16704 жыл бұрын
Why and what purpose you have made this item.
@klausbrinck21374 жыл бұрын
4: 31 Background-music: "do it right, just do it right" ;-)
@ynsdnk3 жыл бұрын
14:20 background music?
@klausbrinck21373 жыл бұрын
@@ynsdnk video-background-music or score.
@ynsdnk3 жыл бұрын
Music name Pisco sour - gunnar olsen 👌🐬
@soyddagirishbhai24983 жыл бұрын
Banake.....krcha....kitnahe
@badboycell6874 жыл бұрын
Faz com 3 motores
@alidoost44303 жыл бұрын
Lack of safety
@PhiTran-cb7pp4 жыл бұрын
Co dieu minh khong hieu can mua thi mua motor manh. Nhung roi lai gang vao banh xe giam toc cho no cham lai de chi. Hoi tuc cuoi. Neu vay mua dai motor khong manh xai khoi can giam toc. Neu mua motor manh xai do giam toc muon manh thi manh muon cham thi cham co ve hop ly hon con gang do giam toc ve lam cham lai roi 2 motor xai het suc toc do cham ri That kho hieu
@bharat43704 жыл бұрын
Bhai de sakta hai kya
@ShahidShaikh-bf5tr4 жыл бұрын
What will the torque
@cezarfr45064 жыл бұрын
At least, say what kind of motors to use it Thanks.
@MsDEEPU9994 жыл бұрын
775dc moters
@vijaydevkate62054 жыл бұрын
Motar bout badeya banini natasse
@threehorsesxxx57593 жыл бұрын
When I was 12 that was about my level of complexity but I never welded bearings.
@creativemind1803 жыл бұрын
Ah??
@chriscraighan44324 жыл бұрын
What kinda clamp force do you get out of a flipflop like that ?? 😂
@ChunnuMunnuTv-4 жыл бұрын
4:35🙄😲😲
@adammesic4 жыл бұрын
But what's it for?
@josephharry87004 жыл бұрын
Looks like a super dangerous way to cut your toenails.
@oturanboga62253 жыл бұрын
pörfek
@Stary_Yeti3 жыл бұрын
It was much easier and faster to replace the windings on the rotors. Less mechanical losses than on a carelessly modified gearbox. Besides, welding completely destroyed the bearings. It was much easier and safer to weld a piece of pipe as a bearing seat. If the idea is good, it is clumsy and thoughtless execution.
@sciencefusion53523 жыл бұрын
I agree
@stevenpneh4 жыл бұрын
dont waste time on this mod, it last only short under 2days.
@adachiluis4 жыл бұрын
4:31 🤦🏻♂️ no way
@klausbrinck21374 жыл бұрын
Background-music: "do it right, just do it right" ;-)
@jitendranihal36792 жыл бұрын
Jitu
@gkhardworkers8174 жыл бұрын
How much price & were available
@ksthacks4 жыл бұрын
Not available
@kingtut59233 жыл бұрын
MUSIS OFF PLEASE
@bharat43704 жыл бұрын
Reply plss
@joshwhitworth46462 жыл бұрын
the music for some of these videos is terrible
@windturbineusa36414 жыл бұрын
learn how to weld
@SuperJosab3 жыл бұрын
The welding is atrocious!
@JodBronson3 жыл бұрын
Job done = Happy. Unless you have OCDB !!! 😂❤️😂❤️😂❤️
@СтефанКоев-к6ь4 жыл бұрын
Man, you are welding a bearings?! You're a technical horror. Please never touch machines again.
@adachiluis4 жыл бұрын
kkkkkkkkkkkkkkk 😂
@klausbrinck21374 жыл бұрын
Still this was my only take-away from this video... not welding bearing, but it gave me an idea... for perfect aligning and welding of a seat of a bearing!
@ksthacks4 жыл бұрын
:(((
@ИгорьБелозер-ъ4я3 жыл бұрын
Какая грубая работа
@law21814 жыл бұрын
The non safety way
@AdS-rsa-gea-getra-product4 жыл бұрын
🤣 gk ada fungsinya
@tanvirulislam9574 жыл бұрын
You are a mechanic. Full wrong.
@ksthacks4 жыл бұрын
I am not a mechanic
@johnbravo75424 жыл бұрын
Man,that is really dumb!
@ksthacks4 жыл бұрын
why??
@GopalKumar-jl7yj4 жыл бұрын
Mujhe pura set chahie6201792533
@hughsgarbagetrucks3 жыл бұрын
Fake bull crap
@dpkcreativity3 жыл бұрын
*♥️जय हिंद ♥️भारत माता की जय ♥️वंदे मातरम* ♥️JAY HIND ♥️ BHARAT MATA KI JAY ♥️ VANDE MATARAM ♥️🇮🇳
@gangleweed4 жыл бұрын
Typical hack and bash engineering .com.............when I see this type of metal hacking I get a strong desire to get outta here........
@ksthacks4 жыл бұрын
:)))
@Titanis20004 жыл бұрын
I love this high tech east Indian machining
@Anhad13137 ай бұрын
please make more videos
@juancarlostaveraoviedo6767 Жыл бұрын
Song name 2:56 please
@elecktronvitass19094 жыл бұрын
варить корпус подшипника.. несогласен, это какое-то крайне-временное решение, извините но от меня дизлайк.
@ksthacks4 жыл бұрын
oh! thank you :)
@JackKingston-jj3ft8 ай бұрын
Power usage
@АлександрСтепанов-у7л4 жыл бұрын
Варить подшибник это мощьно!
@tacoboi-rp1mq Жыл бұрын
bruh
@михаилчистяков-з9з3 жыл бұрын
hello.what kind of melody is playing 13:10?please write the name of the track?
@viethungle4064 жыл бұрын
Bi mà hàn trực tiếp vào là sai, phải có Balie, bạn không hiểu gì về cơ khí
@ВладимирОмнамах3 жыл бұрын
Ну и как долго он у тебя проработает на сухую?..2 недели?..а парился дня 2.. В редукторах дырки насверлил..смазки нет..с цепи на таких оборотах тоже всё слетит..какой смысл?..руки занять только что
@dusolexamanswers98363 жыл бұрын
1:23 pai aap kya cut kar rahai ho
@ПавелЕвлаш-р2ъ4 жыл бұрын
за труды конечно лайк......но всё равно не ясно чем не угодили родные двигателя?775 двиг работает от 12 до 36 вольт.подключал все равно 12в.короче непонятка