Suspension Work | Hendrickson Z-Spring

[@johnmcgreevy742]

Don't really know much about working on this heavy duty machinery, but I love to watch you work on it, you make it look simple though I know better Thanks!!

[@SemiWorkin]

Thanks for watching and commenting!! It takes a lot of editing to make it look that easy.

[@johnmcgreevy742]

@@SemiWorkin Thank you for replying, love to watch

[@isaaccharles1189]

Great video semi working I am learning a lot from your videos keep them coming

[@SemiWorkin]

Thanks for watching my videos I really appreciate it!!!

[@johnz8210]

That looked pretty easy compared to the walking beams. Also this set-up appears to weigh substantially less than some other designs. Thanks for the video.

[@SemiWorkin]

Thanks for watching!! This suspension has more moving parts so it takes more maintenance.

[@nickpersenaire4443]

Keep up the great content. You sure make it look easy.

[@kendall2205]

@SemiWorkin thinking I need to change my z spring. Noticing ride height difference between the right side and the left side, with the left side being about an inch higher where I measured in the rear. I noticed that whoever had the truck before me changed the z spring on the front left drive axle but didn't change the opposite side. Do you think that would cause the suspension to ride higher on the side the new one was put on vs the old z spring side? Also, I see you have jack stands under the axle that u put in once u jacked up wheels high enough to get off ground. What are you doing to take the weight off that z spring? Jacking frame up as well? Air in bags vs empty? Etc. Just curious how to go about doing it. Thanks for the vid!

[@jasonteichroeb5069]

For light weight Z springs work but on a grain truck loading 18 19 tons they break easily

[@stevenlinford4312]

As somone who hauls boulders every day, can confirm.

[@sandmennivicevic99]

What's the total time for replacing one of those z leaf springs like here ?

[@lechido9288]

Good job, as always.

[@SemiWorkin]

Thanks for watching!!

[@remigiohernandeztorres5093]

En la z que tiene un mack cuantos son sus accesorios

[@lazaro1969]

Muy buen videos good

[@oluwasodejayi7316]

What capacity impact wrench did you use for the u bolts in ft lb

[@kevinhornbuckle]

I learned a few things here.

[@SemiWorkin]

Thanks for watching!!

[@hunterbiden001]

why take tires off. we never do even replacing z bar spring or wear pads . just to make a few more dollars on shop time

[@farwest571]

Iv never seen a truck with that type of z bar suspension....is there any advantage to it?

[@davidrfowler6432]

yes !! independent rear suspension some what anyway, the rear axle is too close to the bottom of the frame , so the "Z" bar was invented to allow longer length air bags for more weight carrying capacity and suspension smoothness

[@farwest571]

@@davidrfowler6432 ah ok thanks... ya makes sense

[@SemiWorkin]

Thanks for watching!! Advantages are air ride makes smoother ride and heavier loads. Disadvantages are more moving parts equals more maintenance.

[@raymonwilson9221]

Let’s pretend I’m stupid 1. Why did you do it 2. What really changed

[@SemiWorkin]

Thanks for watching!! The U-bolts were riding loose, the wear pad was gone, and the roller bolts were gone.

[@rogerdominguez15]

This always happens on my mack dump truck.Airing up and down the suspension while dumping wear out the components very quick.

[@ethanrobichaud154]

I recently bought a older western star with same suspension, my first air ride truck as an owner operator, very informative and helpful I know I'll pay a little more attention and plan to upgrade in the near future. Keep up the good work👍

[@oscarsanmartin268]

Realmente un trabajo al pedo, cambiar grampa por grampa es tirar plata, pero bue las grandes empresas son asi

[@ДенисСеверинов-э6м]

Стремянки можно снять, зачем резать..