Suzuki Burgman 400 - Engine Oil / Oil Filter Change - 2017 - Current | Mitch's Scooter Stuff

[@MitchsScooterStuff]

Engine Oil - amzn.to/3VkMPdw Oil filter - amzn.to/3Vm2mtE Ratchet 3/8 drive - amzn.to/2hhmnUs 3" / 6” extension set 3/8 drive - amzn.to/2h7ypMl 8mm socket 3/8 drive - amzn.to/2xLNVXU 14mm socket 3/8 drive - amzn.to/2xGn4Ms 17mm socket 3/8 socket - amzn.to/2EMT6LO Rags - amzn.to/2Yh8jvg Torque wrench 0-150 lb/ft 3/8 drive - amzn.to/2Crqq4R Nose pliers - amzn.to/2yetDDj Funnel (long) - amzn.to/2v5mYLn Oil pan / jug

[@noorfaesl5608]

Hello, hello, my brother has a problem with my bike, the first generation PC X, and he has a problem with the rear wheel, it makes a loud sound

[@yip9126]

Even owner's manual does not show such detail demostration as you did. Thank you Mitch👍

[@MitchsScooterStuff]

Happy to help!

[@robchambers5686]

Thanks for all of your effort/time/knowledge/clarity. Scooter owners everywhere know how valuable your channel is!

[@MitchsScooterStuff]

Hi Rob! You're welcome! Thank you so much for the support!!

[@sevketdan4444]

Oh sooo 🎉

[@douglaslee742]

Just bought a 2018 Burgman 400. After watching this oil change video for 2017 to current 400’s I clicked on your Amazon link to buy an oil filter and it showed filters fitting 2007 to 2016 only.

[@M4rkle]

Great video as always Mitch - well shot and well explained. Just to say that the Burgman's oil level should be measured upright and off the centre stand. I made this mistake (despite it saying so very clearly in the manual - d'oh!) when I first purchased my Burgman. The oil level while on the centre stand shows a higher reading than that off the centre stand, meaning you could potentially be running with too little oil. Probably not enough to do any damage I realise, but worth being aware of :)

[@icejd7]

Great videos. But I have same question. Is it necessary to remove oil gallery drain plug and what does it do? Tnx

[@jimbowats]

Great video, just to be safe however, the oil Drain bolt tightening torque is 23nm, not the 12nm stated.

[@Samuel10463]

Mitch, the oil you recommend is MA type, for wet clutch motorcycles. It has additives to prevent clutch from slipping. Oil for scooters is MB type, without those extra additives, scooters don't have wet clutch. MB oil is more "slippery" than MA oil, which is beneficial for scooters, because they run on very high RPM most of the time, and MA oil isn't the best in this case.

[@Samuel10463]

"While JASO MA lubricants are in fact suitable for all applications, MB lubricants may induce clutch slippage in motorcycles and must only be used in scooters."

[@mervineng2705]

I like how you tighten the bolts to the specific torque ratings. Not all bikeshops do that. =)

[@sonyyoung1036]

Have you always used the R5000 10w40 mineral engine oil vs synthetic engine oil?

[@robchambers5686]

Hi Mitch, can you please list the part numbers and a source for the oil plug crush washer, and the small o-ring that goes with the oil filter...?? (2020 Burg 400) I can't seem to find accurate details for those parts. Thank you

[@a761111abc]

Hi，oil filter cover screws is 3.2nm or 10nm?

[@LadyDC45]

Thank you Mitch this is very helpful I have a 2007 400 also.

[@johnwhite4470]

Excellent stuff yet again Mitch 👍🏻

[@inkyvampire4095]

Three Q’s. 1) Is it really needed to remove the “gallery plug”? The manual doesn’t say to touch it. 2) Where do you find a torque wrench that goes as low as 2.3ft-lb? I can’t find one anywhere. Lowest is 5ft-lb that I have found. - my manual doesn’t give torque value on these at all. 3) manual for 2019 says drain bolt torque is 16.5ft-lb torque, not 17. So is this video “to current” good for 2019? Could your filter cover bolts really be different from my model too? Thanks so much.

[@icejd7]

Great videos. But I have same question. Is it necessary to remove oil gallery drain plug and what does it do? Tnx

[@eddieg5466]

Hello there Mitch, have you ever done a replacement of the oil sight glass because of leaking..? Mine started to resuming oil a little bit, and there is not much videos out there about the topic , thank you on advance, big fan of the channel by the way !! Best regards Eddie..✌

[@giuseppe39439]

Grazie video 🎞️ utilissimi. 👍🏻

[@mamadretro]

Hi,the engine oil needs how many bottles?

[@MitchsScooterStuff]

hi, 1 and little less than half

[@dIsAstErTR]

The user manual recommends 1300ml.

[@bally632]

Are you going to film a hub oil change on this latest burgman? 😀

[@MitchsScooterStuff]

Funny you asked, will get it done this week! 😄🤙🏼

[@manojbalasubramanian4233]

Super explaination bro 👏👏👏

[@altaycani]

After i did exact things , when i turn on the ignition my engine and f1 light started to come on , ? How can i delete this f1 code ? I cant reset the oil meter because of f1

[@MitchsScooterStuff]

When you turn key on, if fi come on, turn key on again quick, it might disappear

[@MitchsScooterStuff]

Did you see my fi fix video?

[@altaycani]

@ no , could you please post the link?

[@smaad7]

I wish I live in your country so I could give you my 2006 Piaggio fly lmao the low oil pressure light won't come on ignition and I don't know how to change it so I drive my scooter without low oil indicator is it dangerous?

[@andrewpark7242]

My oil drain out of my vespa and killed the engine so be careful

[@michaelpennington8475]

Did you get a new 400 ? If you did are there any reviews of it ?

[@MitchsScooterStuff]

Hey, no it's my friend Mario's ... not yet but when it will be sitting next to my 07 model, and will do comparison and review

[@michaelpennington8475]

@@MitchsScooterStuff Fantastic 👍

[@thenov1944]

Wash Parts ( All ) in solvent ! ! Dont wipe with rag & get Lint & Dirt on parts & Threads ! Spray solvent can help !

[@김성재-b9y]

Thank you very much indeed!

[@MitchsScooterStuff]

You're welcome!

[@darioallievi7160]

Questo è la dimostrazione dell'olio motore, è quella della trasmissione 🤔❓

[@alexandrudamian6582]

Respect 👍

[@MitchsScooterStuff]

❤️🙏🏼

[@RogierYou]

This could have been a manufacturer video!

[@MitchsScooterStuff]

Thank you!

[@yongyuthsornphlaeng6088]

Good​

[@MitchsScooterStuff]

Thanks

[@Charlieperez714]

Suzuki Brea CA wants to charge $400+ for this little job, because apparently they have specialized tools .

[@권용희-k1z]

유용한 정보 감사합니다

[@jameswilkes7824]

Make sure to run it outside 😴

[@MitchsScooterStuff]

Haha yeah, garage door is open :)

[@thenov1944]

D a h ! !