T-Maxx Conversion Mounting your Motor and setting the Gear lash

[@RCRoads]

The motor mount you are showing is nice. It seems like you could mount quite a large pinion gear on the motor and have plenty of room. Nice setup and explanation on how to. 👍👍

[@jessev4615]

Great video, dang simple if u know rc. I bought one of you Titan 775 motor mount plates a few weeks back. Love it tmaxx works great with spare summit electronics in it. A godsend for a 2003 tmaxx 2.5 truck that before I watched your videos was the forgoten spider trap in the corner for the last 4 years. Know it's rejoined the 8 other electric r/c in my collection. Awesome plates & engneering behind it.

[@TheRoadTaken]

I have a TMaxx with the .15 engine, 20 years old that is also sitting collecting dust. This might just breath new life into that truck!

[@jessev4615]

Daryl lackey: I haven’t seen a peep from the guy who runs this channel in a long time. If u can get one of his Brackets tho it will work well. There great Quality and do exactly what he describes. Good luck

[@georgeorge5327]

I purchased a set of these: Bondhus 16599 Set of 9 Balldriver Stubby L-wrenches, sizes 1.5-10mm they reached the bottom screw.

[@nickz1122]

what is the recommended/your favorite brushless combo for the T-Maxx?

[@strider9583]

Love your video sir currently in process of making aluminium plate for it here in southwales uk

[@johndickie8085]

You could just buy one from me at www.How2RC.com it would be easier. We ship world wide

[@Phil-justphil]

@@johndickie8085 i did and they are awesome south essex UK

[@TheVandorian]

Hello do you still have the conversion for the tmax doing a conversion to electric and how do I lock the gears so I have reverse and brake thank u Anthony P Sharp.

[@tobydyes]

Why aren't you using Loctite

[@georgeorge5327]

I have a 2.5, where did you get your drive shafts, are they custom?

[@juanervin5889]

Where did you get your center steel driveshaft at. I have 2.5 t-maxx

[@How2RC]

I have had them for years , I don't remember.

[@juanervin5889]

@@How2RC thx u sir I been trying to find them for the longest

[@BrentTheGent1]

How2RC,, can you spare time to look at the last vid i posted about my 1/8 nitro to brushless conversion,, i think i could run a motor straight onto the centre gearbox, as it has clutch, 2 speed which may need locked?? unsure,, but look forward to ordering what i need from you, Thankyou very much!! from bonnie Scotland!! 😊

[@How2RC]

It looks like one of our Motor mounts might work for you car. look at them on www.How2RC.com under T-Maxx motor mounts.

[@BrentTheGent1]

How2RC ,,Thanks a bunch fella!! will have a look after hours! i love your ways with rc cars man,,

[@BrentTheGent1]

How2RC ,,, that looks like it could be the one,, i am trying to source the diff,, and have started a project for my daughter, so i can take my time and get this build right,, thanks!!

[@redneckliamlarabel5751]

Can some one tell me where I can get a pinion gear whit 3mm shaft hole and will work good on a 54t spur

[@mikegregory9915]

Does it matter what pinion gear and spur gear you use like pinion 22 tooth spur 72 tooth

[@johndickie8085]

The larger the pinion is the faster you go, untill you fry the motor. A smaller pinion gives you more pulling power.

[@juanervin5889]

Where did u get the steel drive shaft at

[@johndickie8085]

Merry Christmas, I get Steel Driveshafts from Traxxas #5451R..

[@redblue40rc33]

Your website don't exist anymore for the Tmaxx motor mounts.....ugh

[@andyh5931]

Also looking for a mount in UK, no luck.

[@chrisheard7849]

Do you sell the motor mount? our where I can get one .?

[@thomdoers3222]

I just got mine this week from him. www.how2rc.com I wasn't sure because he's been inactive, but you can still get them from him there

[@semjr.3081]

is that the stock pinion gear?

[@How2RC]

It is a Robinson Racing machined steel pinion and spur.

[@dyllonclark3747]

How2RC how many teeth is the pinion and is still have a 72tspur?

[@408martian]

What kind of motor mount was that?

[@johndickie8085]

The motor mount in this video is the Tall Mount with ESC tray, available at How2RC.com

[@johndickie8085]

It is a 550 size Brushless motor 6.5t,3400Kv

[@bondebos3478]

great vid! keep it up!

[@How2RC]

Anthony Watch our video on Transmission here on out You Tube channel. How2RC

[@tobydyes]

You're going to let the battery sit on them screw heads I can see a fire in your future

[@pmatrisotto]

Gear lash? its called gear mesh

[@johndickie8085]

The amount of movement between the 2 gears is called gear lash!