T-Motor F4 Flight Controller Overview

[@archer4922]

Sweet. Glad to see t-motor adding new products. I love their f45a 4n1 esc.

[@carlgill5946]

Love how you sing the whole time!!......

[@admargodoy]

Gal, the pin + in belt connector 4IN1 ESC is to 5v or Battery+?

[@KremerFPV]

Battery.

[@wilfredocampo4215]

Hi, just wondering if the SBUS receivers such as FRSKY and tbs crossfire will work on this FC?

[@KremerFPV]

Yes, of course.

[@wilfredocampo4215]

Gal Kremer, thank you very much

[@SuperRepoman77]

Where do you run the sbus wire?

[@calixtedecouttere8431]

Hi ! Thx for ur videos How to reboot this fc ?

[@KremerFPV]

My pleasure. Are you referring to DFU mode?

[@lord_scrubington]

quick question, is this board powerful enough to run ArduPilot?

[@KremerFPV]

I’m not sure if it’s supported.

[@randysem1194]

Hi do you have a video of installing cross fire to this f4 fc? I've been having trouble especially using all the right wiring diagram t motor tells you too! Have it on uart5 r5 t5 just no stick movement in my rx tab in betaflight! It was a ft5 bnf 4s should I upgrade the firmware? Was purchased on Christmas 2020! I did hear you say it comes with beta 3.5 installed

[@KremerFPV]

Hi, I don't have a specific video about this flight controller and CRSF. If you don't have any previous experience setting up a CRSF RX, check out this guide: kzbin.info/www/bejne/iWqTiKuAjdmFkM0

[@MCsCreations]

Great review, Gal! 😊 I'd prefer a F7 board, but it's a great start! 😊

[@GalaxystarNo1]

Can I use this with a Flysky Nirvana? Can I connect the Flysky Receiver to that stack?

[@KremerFPV]

Sure you can.

[@befpv729]

Hi . I connected s.sport of rx like wire shiw for this fc. But the TE port on fc what is the cobfigurztion betaflight ?

[@KremerFPV]

Hi, did you get it sorted?

[@befpv729]

@@KremerFPV no still looking information

[@IBHobbies]

Hallo nice review sir. Can I use this FC for VTX walksnail Avatar Micro with power input 6 V - 25.2 V?

[@KremerFPV]

Thanks. Sure - you can power it directly from the battery pads.

[@IBHobbies]

@@KremerFPVya thanks. its mean, need a bec or step up for powering vtx right?

[@KremerFPV]

@@IBHobbies not necessarily.

[@befpv729]

Have you any curent sensor calibration setting value ?

[@KremerFPV]

No, I don't have it, sorry.

[@mikediggsv2]

Hi GAL i have a problem i just updated to 4.2.8 and the te pad not working for s-port FC came with 4.1.1 and worked so is there something i have to type in the CLI ???

[@KremerFPV]

Hi, there might be an issue with 4.2.8. Try using an earlier version.

[@srqcrna]

Thanks for video!!! If I use 6s lipo will the DJI air unit be ok getting power from this FC?

[@KremerFPV]

My pleasure. No - as it only has a 5v BEC...

[@snakefich]

Thanks for the review, how much amp is the 5v Bec? and do all the 5v pads have 1or 2 amps? Thanks

[@KremerFPV]

You're welcome. 2A which is shared between all the 5v pads.

[@snakefich]

@@KremerFPV Thanks, Happy Flying

[@PropsOff]

Great Review! Cant wait to see it in action.. I may be buying it aswell.. From your link of course...

[@KremerFPV]

Thanks, I appreciate it!