For me the FPV Cycle (Kabab FPV) BabyTooth concept is the ultimate compromise between light weight and flight performance. Have an original 3" one with Zeez 1S board and 1204 mm motors (based on RCinpower, if I am not mistaken). With a light camera it can be squeezed under 60 grams AUW. Have suffered from RX loss due to FrSky system losing its lock above a football field at perhaps 50 meters altitude, the quad basically "glided down". No damage, since almost no inertia. It flies like a laser pointer, you just point and it goes. No noise, just a slight humming noise. Love it.....
@DutchRC2 жыл бұрын
correct.. the Kebab motors are all made by RCinpower.. and haha yes.. there is just not enough gravity to have these kinds of quads damage themselves ;)
@MCsCreations2 жыл бұрын
Awesome flying and review, dude! 😃 What about the flight time? I may have lost when you said it and someone talked to me here. 😬 Anyway, stay safe there with your family! 🖖😊
@DutchRC2 жыл бұрын
Thanks as always brother! :) flight-time is from 5 to max. 10 minutes.. pretty ok? Cheers and be safe!
@ShadowOppsRC2 жыл бұрын
Those Emax Avans are good props! Super durable I have found out from experience. Thanks for sharing!
@DutchRC2 жыл бұрын
Welllll yes so I had those props on the iFlight RS136.. that combo was good but these little 1102 motors can't handle the props :$
@ShadowOppsRC2 жыл бұрын
@@DutchRC makes since. Have really aggressive pitch.
@jamiemonkey13622 жыл бұрын
Would of been great if they made a 2s version with a bit more power. At £131 I'm thinking no
@DutchRC2 жыл бұрын
pstttt: the ESC's are 2S capable and the motors relatively low Kv :) What do you think? :)
@jamiemonkey13622 жыл бұрын
@@DutchRC Well in that case. I'd have to upgrade it just to see. 😉😂
@DutchRC2 жыл бұрын
@@jamiemonkey1362 It might need lower pitch prop on 2S.. ohwww wait! I already have lower-pitch props on it :P Regretably I don't have 2S lipo's :$
@jamiemonkey13622 жыл бұрын
@@DutchRC Well you could try wiring it like a 2s whoop and use two 1s batteries 😉
@DutchRC2 жыл бұрын
@@jamiemonkey1362 yeahhhhh so I have zero PH2 parts / connectors and would love to keep it like that :D.. also: to heavy (?) I know 350mah cells are kinda junk but will have a look if there are small 2S packs available with PH2 connector
@maddercat10 ай бұрын
I'm having trouble with the vtx, I can't get it to change channel or power. It wasn't set up when I got it, and it says smartaudio undefined.
@DutchRC10 ай бұрын
check if the Betaflight Configurator says the VTX is "connected" in the VTX tab. (says so on the right.. and you need the flight-battery to be connected).. I'm guessing BF will say it does not see the VTX... right? That then means the setup in your Ports tab is incorrect for the VTX... is it maybe on a different port? Or is the protocol wrong?
@maddercat10 ай бұрын
@@DutchRC nope, the vtx was showing as ready, but still smartaudio undefined and yes with the battery plugged in and it's going and outputting video, but I can't change the channel or power in betaflight or in the osd. In the osd I can set it to a different channel, but it doesn't save. I even swapped the uart to tx2 and the reciever to tx1, same problem. I'm thinking it must be the vtx table they have on their site doesn't match. The vtx is their brand but they have no manual on it or any support, and they don't sell it separately. I swapped it out for a goku625 I had in another drone of mine and its working properly with tramp protocol.
@okkie_26562 жыл бұрын
I bought this one knowing it would be really hard for me to setup. I've never soldered and I'm new to FPV flying : ) So yeah, I knew I was getting into trouble. But if you don't try then you're sure never to succeed. Found a youtube video showing me exactly how to wire a Radiomaster EP2 and it looks like it worked. After quite some fiddling I got a solid green light on that receiver telling me (I think) that it's bound to the Radiomaster Zorro ELRS only radio. Next step, fire it up and fly. Nope, betaflight doesn't show any axes moving but I do have this nice view of a rotating drone whenever I move it by hand. This will take alot more studying and trying but well.... I knew what I was getting into : ) I have another drone incoming too, this one with the ELRS receiver built in. That's a good test case to see if I even set up the radiomaster radio correctly.
@DutchRC2 жыл бұрын
Checking the rest of the setup that way will work! :D Other then that I assume the port-setup for the receiver and/or the receiver-type isn't set correctly in betaflight? :$ Quite a challenge regardless this one for a first solder job :D
@okkie_26562 жыл бұрын
@@DutchRC Quite the challenge it was indeed. Betaflight just didn't accept the input from the Radiomaster. Spent about 8 hours looking at instruction videos, trying out things, flashing this and that to the same version, the Feather just didn't arm, etc. And then suddenly it all worked and it flies exactly like I hoped it would (smooth, slow and very quiet). Quite the experience but it feels like if this can be handled then I'm ready to face whatever more FPV will throw at me. It sure helps to love flying, been flying gliders and have millions of hours in different flight sims. So that gives the motivation to just keep going when things are not going as wanted.
@DutchRC2 жыл бұрын
@@okkie_2656 Ohwww good on ya on fixing that :D No idea what changed?? :P And true! work of most any other FPV drone will be Easier indeed :D Not bad at all man.. I just assisted a friend in building a quad (also with an AIO board of that size).. it's NOT easy :)
@chrisbee54812 жыл бұрын
You should do a comparison to the emax 1S 3" TP nanohawk X. I think that one is a better BNF. Or maybe the 1S happymodel crux3. I built my own TP3. The flywoo 1203 11500kv motors are the best 👌 on the emax 3" Biblade props. For 1102 I like the happymodel 13500kv motors on 1S and gemfan 2036 props.
@DutchRC2 жыл бұрын
yeahhh so the Crux3 will probably be easier to fly (?) on the other hand: 1 toothpick is about enough for me :D most times they are unflyably over here due to the wind :D
@erlandfpv2 жыл бұрын
Suggest : flyng around park like this, better using legacy mode for rapidfire, more better images and colours ^^
@DutchRC2 жыл бұрын
:O not sure what you ment :O why fly around the park?
@erlandfpv2 жыл бұрын
@@DutchRC you'rs analog module it's rapidfire right? I mean you will get the more better colours and fpv feed when using legacy mode setting in the rapid fire module.
@DutchRC2 жыл бұрын
@@erlandfpv thanks for the tip brother :) I'll check it out :)
@shortclipsvictoria7892 жыл бұрын
Might as well go with Crux. Nicer camera and lower price tag. This is like Mobula 7 turned into a toothpick.
@DutchRC2 жыл бұрын
yes but not everyone want a whoop :) (me for instance :P)